I am experiencing fairly consistent system freezes which seem to
coincide with using the ndis driver and nvidia driver at the same time.
I had worst problems using the nvidia binary driver, but I did also
experience a freeze one time with the xorg nv driver, which I am now
using. Sometimes the wireless card works extremely slowly when I am
using the nvidia driver.
I have a Dell Latitude D800. I enclose dmesg. Any advice on how to
either further diagnose, or fix the problem will be welcome.
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-BETA2 #0: Sat Nov 10 12:48:18 CST 2007
stephen@hub2.gateway.2wire.net:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) M processor 1.70GHz (1698.56-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6d6 Stepping = 6
Features=0xafe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
Features2=0x180<EST,TM2>
real memory = 536535040 (511 MB)
avail memory = 511066112 (487 MB)
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <DELL CPi R > on motherboard
acpi0: [ITHREAD]
acpi0: reservation of 0, 9fc00 (3) failed
acpi0: reservation of 100000, 1fef0000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci_link1: BIOS IRQ 11 for 0.31.INTB is invalid
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> mem
0xfc000000-0xfcffffff,0xd0000000-0xdfffffff irq 11 at device 0.0 on pci1
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f
irq 11 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f
irq 11 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f
irq 11 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ehci0: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> mem
0xf4fffc00-0xf4ffffff irq 11 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
uhub3: 6 ports with 6 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci_link1: BIOS IRQ 11 for 2.3.INTA is invalid
pci2: <ACPI PCI bus> on pcib2
pci0:2:0:0: bad VPD cksum, remain 14
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x3001>
mem 0xfaff0000-0xfaffffff irq 11 at device 0.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5705 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bge0: Ethernet address: 00:0f:1f:21:d5:92
bge0: [ITHREAD]
cbb0: <TI7510 PCI-CardBus Bridge> at device 1.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [ITHREAD]
cbb1: <TI7610 PCI-CardBus Bridge> irq 11 at device 1.1 on pci2
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
cbb1: [ITHREAD]
fwohci0: <1394 Open Host Controller Interface> mem
0xfafef800-0xfafeffff,0xfafe8000-0xfafebfff irq 11 at device 1.2 on pci2
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 48:4f:c0:00:36:a9:44:a1
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 4a:4f:c0:a9:44:a1
fwe0: Ethernet address: 4a:4f:c0:a9:44:a1
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 48:4f:c0:00:36:a9:44:a1 @ 0xfffe00000000, S400,
maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x13b0000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
pci2: <base peripheral> at device 1.3 (no driver attached)
ndis0: <Dell TrueMobile 1300 WLAN Mini-PCI Card> mem
0xfafec000-0xfafedfff irq 9 at device 3.0 on pci2
ndis0: [ITHREAD]
ndis0: NDIS API version: 5.1
ndis0: using obsoleted if_watchdog interface
ndis0: Ethernet address: 00:90:96:f6:2d:0e
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xbfa0-0xbfaf at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pcm0: <Intel ICH4 (82801DB)> port 0xb800-0xb8ff,0xbc40-0xbc7f mem
0xf4fff800-0xf4fff9ff,0xf4fff400-0xf4fff4ff irq 9 at device 31.5 on pci0
pcm0: [ITHREAD]
pcm0: <SigmaTel STAC9750/51 AC97 Codec>
pci0: <simple comms, generic modem> at device 31.6 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model GlidePoint, device ID 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
sio0: [FILTER]
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcf7ff,0xcf800-0xcffff pnpid
ORM0000 on isa0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1698564643 Hz quality 800
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ad0: 28615MB <IC25N030ATMR04 0 MOAOAD0A> at ata0-master UDMA100
acd0: CDRW <QSI CD-RW/DVD-ROM SBW242U/UD25> at ata1-master UDMA33
cbb1: power timeout, doom?
cbb1: Power not on?
pccard1: <unknown card> (manufacturer=0x0097, product=0x1620,
function_type=-1) at function 0
pccard1: CIS info: TEXAS Instruments, UltraMedia Smart Card Adapter, 1.0
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00
cd0 at ata1 bus 0 target 0 lun 0
cd0: <QSI CDRW/DVD SBW242U UD25> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
Trying to mount root from ufs:/dev/ad0s2a
Setting ESSID to ""
Setting ESSID to ""
Setting ESSID to "stephen"
Setting ESSID to "stephen"
Setting ESSID to "stephen"
Setting ESSID to "stephen"