Continuing my problems with the IBM blade: Booting with ACPI module enabled (btw. live boot CD with sysinstall doesn't load ACPI, but the installed system does?) hangs the system somewhere after first USB bus is found (booting verbose doesn't show any new lines before or after this step). It appears to be a real hang instead of a timeout because I left it 30 minutes and it didn't continue. Booting without ACPI on the other hand doesn't find all the CPU's :( Here's sysctl output:> sysctl -a | grep smpkern.timecounter.smp_tsc: 0 kern.smp.forward_roundrobin_enabled: 1 kern.smp.forward_signal_enabled: 1 kern.smp.cpus: 1 kern.smp.disabled: 0 kern.smp.active: 0 kern.smp.maxcpus: 16 Here's the mptable -dmesg output: ============================================================================== MPTable ------------------------------------------------------------------------------- MP Floating Pointer Structure: location: EBDA physical address: 0x0009d140 signature: '_MP_' length: 16 bytes version: 1.4 checksum: 0xfe mode: Virtual Wire ------------------------------------------------------------------------------- MP Config Table Header: physical address: 0x0009e9b0 signature: 'PCMP' base table length: 388 version: 1.4 checksum: 0x77 OEM ID: 'IBM ENSW' Product ID: 'LEWIS SMP ' OEM table pointer: 0x00000000 OEM table size: 0 entry count: 37 local APIC address: 0xfee00000 extended table length: 408 extended table checksum: 159 ------------------------------------------------------------------------------- MP Config Base Table Entries: -- Processors: APIC ID Version State Family Model Step Flags 0 0x10 BSP, usable 15 1 2 0x0301 2 0x10 AP, usable 15 1 2 0x0301 1 0x10 AP, usable 15 1 2 0x0301 3 0x10 AP, usable 15 1 2 0x0301 -- Bus: Bus ID Type 0 PCI 1 PCI 2 PCI 3 PCI 4 PCI 5 PCI 6 PCI 7 PCI 8 PCI 9 ISA -- I/O APICs: APIC ID Version State Address 14 0x11 usable 0xfec00000 13 0x11 usable 0xfec02000 -- I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# INT conforms conforms 9 1 14 1 INT conforms conforms 9 0 14 2 INT conforms conforms 9 4 14 4 INT conforms conforms 9 6 14 6 INT active-hi edge 9 8 14 8 INT conforms conforms 9 11 14 11 INT conforms conforms 9 12 14 12 INT conforms conforms 9 13 14 13 INT conforms conforms 9 14 14 14 INT conforms conforms 9 15 14 15 INT conforms conforms 0 3:A 14 3 INT conforms conforms 0 3:A 14 3 INT conforms conforms 0 3:A 14 3 INT conforms conforms 0 5:A 13 0 INT conforms conforms 2 4:A 13 1 INT conforms conforms 2 5:A 13 2 INT conforms conforms 3 4:A 13 3 INT conforms conforms 3 5:A 13 4 INT conforms conforms 3 5:B 13 5 -- Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# NMI conforms conforms 9 0 255 1 ExtINT conforms conforms 9 0 255 0 ------------------------------------------------------------------------------- MP Config Extended Table Entries: -- System Address Space bus ID: 0 address type: memory address address base: 0xa0000 address range: 0x20000 -- System Address Space bus ID: 0 address type: memory address address base: 0xf8000000 address range: 0x2000000 -- System Address Space bus ID: 0 address type: prefetch address address base: 0xf0000000 address range: 0x8000000 -- System Address Space bus ID: 0 address type: memory address address base: 0xea000000 address range: 0x6000000 -- System Address Space bus ID: 0 address type: memory address address base: 0xe7000000 address range: 0x1100000 -- System Address Space bus ID: 0 address type: memory address address base: 0xe5000000 address range: 0x1000000 -- System Address Space bus ID: 0 address type: memory address address base: 0xe4000000 address range: 0x1000000 -- System Address Space bus ID: 0 address type: memory address address base: 0xe3000000 address range: 0x1000000 -- System Address Space bus ID: 0 address type: memory address address base: 0xe2000000 address range: 0x1000000 -- System Address Space bus ID: 0 address type: memory address address base: 0xe1000000 address range: 0x1000000 -- System Address Space bus ID: 0 address type: I/O address address base: 0x0 address range: 0x3b0 -- System Address Space bus ID: 0 address type: I/O address address base: 0x3b0 address range: 0xc -- System Address Space bus ID: 0 address type: I/O address address base: 0x3bc address range: 0x4 -- System Address Space bus ID: 0 address type: I/O address address base: 0x3c0 address range: 0x20 -- System Address Space bus ID: 0 address type: I/O address address base: 0x3e0 address range: 0x3c20 -- System Address Space bus ID: 0 address type: I/O address address base: 0x4000 address range: 0x1000 -- -- Bus Heirarchy bus ID: 1 bus info: 0x00 parent bus ID: 0 -- Bus Heirarchy bus ID: 2 bus info: 0x00 parent bus ID: 1 -- Bus Heirarchy bus ID: 3 bus info: 0x00 parent bus ID: 0 -- Bus Heirarchy bus ID: 4 bus info: 0x00 parent bus ID: 0 -- Bus Heirarchy bus ID: 5 bus info: 0x00 parent bus ID: 0 -- Bus Heirarchy bus ID: 6 bus info: 0x00 parent bus ID: 0 -- Bus Heirarchy bus ID: 7 bus info: 0x00 parent bus ID: 0 -- Bus Heirarchy bus ID: 8 bus info: 0x00 parent bus ID: 0 -- Bus Heirarchy bus ID: 9 bus info: 0x01 parent bus ID: 0 -- Compatibility Bus Address bus ID: 0 address modifier: add predefined range: 0x00000000 -- Compatibility Bus Address bus ID: 0 address modifier: add predefined range: 0x00000001 ------------------------------------------------------------------------------- dmesg output: Copyright (c) 1992-2007 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 6.2-STABLE #0: Wed Mar 7 15:08:28 CET 2007 root@:/usr/obj/usr/src/sys/SMP Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Dual-Core AMD Opteron(tm) Processor 2216 HE (2400.10-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x40f12 Stepping = 2 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x2001<SSE3,CX16> AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!> AMD Features2=0x1f<LAHF,CMP,SVM,ExtAPIC,CR8> Cores per package: 2 real memory = 4815060992 (4592 MB) avail memory = 4130750464 (3939 MB) kbd1 at kbdmux0 ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) cpu0 on motherboard pcib0: <Host to PCI bridge> pcibus 0 on motherboard pci0: <PCI bus> on pcib0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pcib2: <PCI-PCI bridge> at device 13.0 on pci1 pci2: <PCI bus> on pcib2 bce0: <Broadcom NetXtreme II BCM5706 1000Base-SX (A2), v0.9.6> mem 0xea000000-0xebffffff irq 5 at device 4.0 on pci2 bce0: ASIC ID 0x57060021; Revision (A2); PCI-X 64-bit 133MHz miibus0: <MII bus> on bce0 gentbi0: <Generic ten-bit interface> on miibus0 gentbi0: 1000baseSX, 1000baseSX-FDX, auto bce0: Ethernet address: 00:14:5e:6d:2d:74 bce1: <Broadcom NetXtreme II BCM5706 1000Base-SX (A2), v0.9.6> mem 0xec000000-0xedffffff irq 10 at device 5.0 on pci2 bce1: ASIC ID 0x57060021; Revision (A2); PCI-X 64-bit 133MHz miibus1: <MII bus> on bce1 gentbi1: <Generic ten-bit interface> on miibus1 gentbi1: 1000baseSX, 1000baseSX-FDX, auto bce1: Ethernet address: 00:14:5e:b3:2a:38 isab0: <PCI-ISA bridge> at device 2.2 on pci0 isa0: <ISA bus> on isab0 ohci0: <OHCI (generic) USB controller> port 0x3000-0x30ff mem 0xf9fff000-0xf9ffffff irq 3 at device 3.0 on pci0 ohci0: [GIANT-LOCKED] usb0: OHCI version 1.0, legacy support usb0: SMM does not respond, resetting usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered ohci1: <OHCI (generic) USB controller> port 0x3100-0x31ff mem 0xf9ffe000-0xf9ffefff irq 3 at device 3.1 on pci0 ohci1: [GIANT-LOCKED] usb1: OHCI version 1.0, legacy support usb1: <OHCI (generic) USB controller> on ohci1 usb1: USB revision 1.0 uhub1: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered ehci0: <EHCI (generic) USB 2.0 controller> port 0x3200-0x32ff mem 0xf9ffd000-0xf9ffdfff irq 3 at device 3.2 on pci0 ehci0: [GIANT-LOCKED] usb2: EHCI version 1.0 usb2: companion controllers, 2 ports each: usb0 usb1 usb2: <EHCI (generic) USB 2.0 controller> on ehci0 usb2: USB revision 2.0 uhub2: (0x1166) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub2: 4 ports with 4 removable, self powered uhub3: vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.07, addr 2 uhub3: multiple transaction translators uhub3: 2 ports with 2 removable, self powered uhub4: Cypress Semiconductor 4 Port Hub, class 9/0, rev 1.10/0.01, addr 3 uhub4: 4 ports with 4 removable, self powered umass0: TEAC TEAC FD-05PUB, rev 2.00/0.00, addr 4 umass1: Cypress Semiconductor USB2.0 Storage Device, rev 2.00/0.01, addr 5 umass1: Get Max Lun not supported (STALLED) pci0: <display, VGA> at device 5.0 (no driver attached) pcib3: <PCI-PCI bridge> at device 6.0 on pci0 pci3: <PCI bus> on pcib3 mpt0: <LSILogic SAS/SATA Adapter> port 0x4000-0x40ff mem 0xe8010000-0xe8013fff,0xe8000000-0xe800ffff irq 9 at device 4.0 on pci3 mpt0: [GIANT-LOCKED] mpt0: MPI Version=1.5.12.0 mpt0: mpt_cam_event: 0x16 mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). mpt0: mpt_cam_event: 0x12 mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required). mpt0: mpt_cam_event: 0x16 mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). pci3: <serial bus, Fibre Channel> at device 5.0 (no driver attached) pci3: <serial bus, Fibre Channel> at device 5.1 (no driver attached) pcib4: <PCI-PCI bridge> at device 7.0 on pci0 pci4: <PCI bus> on pcib4 pcib5: <PCI-PCI bridge> at device 8.0 on pci0 pci5: <PCI bus> on pcib5 pcib6: <PCI-PCI bridge> at device 9.0 on pci0 pci6: <PCI bus> on pcib6 pcib7: <PCI-PCI bridge> at device 10.0 on pci0 pci7: <PCI bus> on pcib7 pcib8: <PCI-PCI bridge> at device 11.0 on pci0 pci8: <PCI bus> on pcib8 orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] ppc0: cannot reserve I/O port range sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 ukbd0: IBM IBM MM2, rev 1.10/0.01, addr 2, iclass 3/1 kbd2 at ukbd0 ums0: IBM IBM MM2, rev 1.10/0.01, addr 2, iclass 3/1 ums0: 3 buttons and Z dir. Timecounter "TSC" frequency 2400100239 Hz quality 800 Timecounters tick every 1.000 msec da1 at mpt0 bus 0 target 0 lun 0 da1: <IBM-ESXS MAY2073RC T107> Fixed Direct Access SCSI-5 device da1: 300.000MB/s transfers, Tagged Queueing Enabled da1: 70006MB (143374000 512 byte sectors: 255H 63S/T 8924C) cd0 at umass-sim1 bus 1 target 0 lun 0 cd0: <HL-DT-ST RW/DVD GCC-4244N 1.02> Removable CD-ROM SCSI-0 device cd0: 1.000MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not present (da0:umass-sim0:0:0:0): got CAM status 0x4 (da0:umass-sim0:0:0:0): fatal error, failed to attach to device (da0:umass-sim0:0:0:0): lost device (da0:umass-sim0:0:0:0): removing device entry Trying to mount root from ufs:/dev/da1s1a stray irq7 bce0: link state changed to DOWN vlan0: link state changed to DOWN bce0: link state changed to UP vlan0: link state changed to UP stray irq7 too many stray irq 7's: not logging anymore mpt0: QUEUE FULL EVENT: Bus 0x00 Target 0x00 Depth 129 -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 262 bytes Desc: OpenPGP digital signature Url : http://lists.freebsd.org/pipermail/freebsd-stable/attachments/20070307/a494786f/signature.pgp
Adding a datapoint: Dell 1950s exhibit similar behaviour but have 2 cores in a single physical CPU. Hope this helps the discussion along. Sam Baskinger Software Engineer Lumeta - Securing the Network in the Face of Change Ivan Voras wrote:> Continuing my problems with the IBM blade: Booting with ACPI module > enabled (btw. live boot CD with sysinstall doesn't load ACPI, but the > installed system does?) hangs the system somewhere after first USB bus > is found (booting verbose doesn't show any new lines before or after > this step). It appears to be a real hang instead of a timeout because I > left it 30 minutes and it didn't continue. > > Booting without ACPI on the other hand doesn't find all the CPU's :( > > Here's sysctl output: > >> sysctl -a | grep smp > kern.timecounter.smp_tsc: 0 > kern.smp.forward_roundrobin_enabled: 1 > kern.smp.forward_signal_enabled: 1 > kern.smp.cpus: 1 > kern.smp.disabled: 0 > kern.smp.active: 0 > kern.smp.maxcpus: 16 > > > Here's the mptable -dmesg output: > > > > ==============================================================================> > MPTable > > ------------------------------------------------------------------------------- > > MP Floating Pointer Structure: > > location: EBDA > physical address: 0x0009d140 > signature: '_MP_' > length: 16 bytes > version: 1.4 > checksum: 0xfe > mode: Virtual Wire > > ------------------------------------------------------------------------------- > > MP Config Table Header: > > physical address: 0x0009e9b0 > signature: 'PCMP' > base table length: 388 > version: 1.4 > checksum: 0x77 > OEM ID: 'IBM ENSW' > Product ID: 'LEWIS SMP ' > OEM table pointer: 0x00000000 > OEM table size: 0 > entry count: 37 > local APIC address: 0xfee00000 > extended table length: 408 > extended table checksum: 159 > > ------------------------------------------------------------------------------- > > MP Config Base Table Entries: > > -- > Processors: APIC ID Version State Family Model Step > Flags > 0 0x10 BSP, usable 15 1 2 > 0x0301 > 2 0x10 AP, usable 15 1 2 > 0x0301 > 1 0x10 AP, usable 15 1 2 > 0x0301 > 3 0x10 AP, usable 15 1 2 > 0x0301 > -- > Bus: Bus ID Type > 0 PCI > 1 PCI > 2 PCI > 3 PCI > 4 PCI > 5 PCI > 6 PCI > 7 PCI > 8 PCI > 9 ISA > -- > I/O APICs: APIC ID Version State Address > 14 0x11 usable 0xfec00000 > 13 0x11 usable 0xfec02000 > -- > I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# > INT conforms conforms 9 1 14 1 > INT conforms conforms 9 0 14 2 > INT conforms conforms 9 4 14 4 > INT conforms conforms 9 6 14 6 > INT active-hi edge 9 8 14 8 > INT conforms conforms 9 11 14 11 > INT conforms conforms 9 12 14 12 > INT conforms conforms 9 13 14 13 > INT conforms conforms 9 14 14 14 > INT conforms conforms 9 15 14 15 > INT conforms conforms 0 3:A 14 3 > INT conforms conforms 0 3:A 14 3 > INT conforms conforms 0 3:A 14 3 > INT conforms conforms 0 5:A 13 0 > INT conforms conforms 2 4:A 13 1 > INT conforms conforms 2 5:A 13 2 > INT conforms conforms 3 4:A 13 3 > INT conforms conforms 3 5:A 13 4 > INT conforms conforms 3 5:B 13 5 > -- > Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# > NMI conforms conforms 9 0 255 1 > ExtINT conforms conforms 9 0 255 0 > > ------------------------------------------------------------------------------- > > MP Config Extended Table Entries: > > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xa0000 > address range: 0x20000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xf8000000 > address range: 0x2000000 > -- > System Address Space > bus ID: 0 address type: prefetch address > address base: 0xf0000000 > address range: 0x8000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xea000000 > address range: 0x6000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe7000000 > address range: 0x1100000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe5000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe4000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe3000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe2000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe1000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x0 > address range: 0x3b0 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3b0 > address range: 0xc > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3bc > address range: 0x4 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3c0 > address range: 0x20 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3e0 > address range: 0x3c20 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x4000 > address range: 0x1000 > -- > -- > Bus Heirarchy > bus ID: 1 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 2 bus info: 0x00 parent bus ID: 1 > -- > Bus Heirarchy > bus ID: 3 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 4 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 5 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 6 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 7 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 8 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 9 bus info: 0x01 parent bus ID: 0 > -- > Compatibility Bus Address > bus ID: 0 address modifier: add > predefined range: 0x00000000 > -- > Compatibility Bus Address > bus ID: 0 address modifier: add > predefined range: 0x00000001 > > ------------------------------------------------------------------------------- > > dmesg output: > > Copyright (c) 1992-2007 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 6.2-STABLE #0: Wed Mar 7 15:08:28 CET 2007 > root@:/usr/obj/usr/src/sys/SMP > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Dual-Core AMD Opteron(tm) Processor 2216 HE (2400.10-MHz K8-class CPU) > Origin = "AuthenticAMD" Id = 0x40f12 Stepping = 2 > > Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> > Features2=0x2001<SSE3,CX16> > AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!> > AMD Features2=0x1f<LAHF,CMP,SVM,ExtAPIC,CR8> > Cores per package: 2 > real memory = 4815060992 (4592 MB) > avail memory = 4130750464 (3939 MB) > kbd1 at kbdmux0 > ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) > cpu0 on motherboard > pcib0: <Host to PCI bridge> pcibus 0 on motherboard > pci0: <PCI bus> on pcib0 > pcib1: <PCI-PCI bridge> at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > pcib2: <PCI-PCI bridge> at device 13.0 on pci1 > pci2: <PCI bus> on pcib2 > bce0: <Broadcom NetXtreme II BCM5706 1000Base-SX (A2), v0.9.6> mem > 0xea000000-0xebffffff irq 5 at device 4.0 on pci2 > bce0: ASIC ID 0x57060021; Revision (A2); PCI-X 64-bit 133MHz > miibus0: <MII bus> on bce0 > gentbi0: <Generic ten-bit interface> on miibus0 > gentbi0: 1000baseSX, 1000baseSX-FDX, auto > bce0: Ethernet address: 00:14:5e:6d:2d:74 > bce1: <Broadcom NetXtreme II BCM5706 1000Base-SX (A2), v0.9.6> mem > 0xec000000-0xedffffff irq 10 at device 5.0 on pci2 > bce1: ASIC ID 0x57060021; Revision (A2); PCI-X 64-bit 133MHz > miibus1: <MII bus> on bce1 > gentbi1: <Generic ten-bit interface> on miibus1 > gentbi1: 1000baseSX, 1000baseSX-FDX, auto > bce1: Ethernet address: 00:14:5e:b3:2a:38 > isab0: <PCI-ISA bridge> at device 2.2 on pci0 > isa0: <ISA bus> on isab0 > ohci0: <OHCI (generic) USB controller> port 0x3000-0x30ff mem > 0xf9fff000-0xf9ffffff irq 3 at device 3.0 on pci0 > ohci0: [GIANT-LOCKED] > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > ohci1: <OHCI (generic) USB controller> port 0x3100-0x31ff mem > 0xf9ffe000-0xf9ffefff irq 3 at device 3.1 on pci0 > ohci1: [GIANT-LOCKED] > usb1: OHCI version 1.0, legacy support > usb1: <OHCI (generic) USB controller> on ohci1 > usb1: USB revision 1.0 > uhub1: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > ehci0: <EHCI (generic) USB 2.0 controller> port 0x3200-0x32ff mem > 0xf9ffd000-0xf9ffdfff irq 3 at device 3.2 on pci0 > ehci0: [GIANT-LOCKED] > usb2: EHCI version 1.0 > usb2: companion controllers, 2 ports each: usb0 usb1 > usb2: <EHCI (generic) USB 2.0 controller> on ehci0 > usb2: USB revision 2.0 > uhub2: (0x1166) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub2: 4 ports with 4 removable, self powered > uhub3: vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.07, addr 2 > uhub3: multiple transaction translators > uhub3: 2 ports with 2 removable, self powered > uhub4: Cypress Semiconductor 4 Port Hub, class 9/0, rev 1.10/0.01, addr 3 > uhub4: 4 ports with 4 removable, self powered > umass0: TEAC TEAC FD-05PUB, rev 2.00/0.00, addr 4 > umass1: Cypress Semiconductor USB2.0 Storage Device, rev 2.00/0.01, addr 5 > umass1: Get Max Lun not supported (STALLED) > pci0: <display, VGA> at device 5.0 (no driver attached) > pcib3: <PCI-PCI bridge> at device 6.0 on pci0 > pci3: <PCI bus> on pcib3 > mpt0: <LSILogic SAS/SATA Adapter> port 0x4000-0x40ff mem > 0xe8010000-0xe8013fff,0xe8000000-0xe800ffff irq 9 at device 4.0 on pci3 > mpt0: [GIANT-LOCKED] > mpt0: MPI Version=1.5.12.0 > mpt0: mpt_cam_event: 0x16 > mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). > mpt0: mpt_cam_event: 0x12 > mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required). > mpt0: mpt_cam_event: 0x16 > mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). > pci3: <serial bus, Fibre Channel> at device 5.0 (no driver attached) > pci3: <serial bus, Fibre Channel> at device 5.1 (no driver attached) > pcib4: <PCI-PCI bridge> at device 7.0 on pci0 > pci4: <PCI bus> on pcib4 > pcib5: <PCI-PCI bridge> at device 8.0 on pci0 > pci5: <PCI bus> on pcib5 > pcib6: <PCI-PCI bridge> at device 9.0 on pci0 > pci6: <PCI bus> on pcib6 > pcib7: <PCI-PCI bridge> at device 10.0 on pci0 > pci7: <PCI bus> on pcib7 > pcib8: <PCI-PCI bridge> at device 11.0 on pci0 > pci8: <PCI bus> on pcib8 > orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > ppc0: cannot reserve I/O port range > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > ukbd0: IBM IBM MM2, rev 1.10/0.01, addr 2, iclass 3/1 > kbd2 at ukbd0 > ums0: IBM IBM MM2, rev 1.10/0.01, addr 2, iclass 3/1 > ums0: 3 buttons and Z dir. > Timecounter "TSC" frequency 2400100239 Hz quality 800 > Timecounters tick every 1.000 msec > da1 at mpt0 bus 0 target 0 lun 0 > da1: <IBM-ESXS MAY2073RC T107> Fixed Direct Access SCSI-5 device > da1: 300.000MB/s transfers, Tagged Queueing Enabled > da1: 70006MB (143374000 512 byte sectors: 255H 63S/T 8924C) > cd0 at umass-sim1 bus 1 target 0 lun 0 > cd0: <HL-DT-ST RW/DVD GCC-4244N 1.02> Removable CD-ROM SCSI-0 device > cd0: 1.000MB/s transfers > cd0: Attempt to query device size failed: NOT READY, Medium not present > (da0:umass-sim0:0:0:0): got CAM status 0x4 > (da0:umass-sim0:0:0:0): fatal error, failed to attach to device > (da0:umass-sim0:0:0:0): lost device > (da0:umass-sim0:0:0:0): removing device entry > Trying to mount root from ufs:/dev/da1s1a > stray irq7 > bce0: link state changed to DOWN > vlan0: link state changed to DOWN > bce0: link state changed to UP > vlan0: link state changed to UP > stray irq7 > too many stray irq 7's: not logging anymore > mpt0: QUEUE FULL EVENT: Bus 0x00 Target 0x00 Depth 129 > >
> isab0: <PCI-ISA bridge> at device 2.2 on pci0 > isa0: <ISA bus> on isab0 > ohci0: <OHCI (generic) USB controller> port 0x3000-0x30ff mem > 0xf9fff000-0xf9ffffff irq 3 at device 3.0 on pci0 > ohci0: [GIANT-LOCKED] > usb0: OHCI version 1.0, legacy supportTo add more info: SMP+ACPI kernel hangs here ^^^^^^^^> usb0: SMM does not respond, resetting > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > ohci1: <OHCI (generic) USB controller> port 0x3100-0x31ff mem > 0xf9ffe000-0xf9ffefff irq 3 at device 3.1 on pci0 > ohci1: [GIANT-LOCKED]But I must use USB for this:> ukbd0: IBM IBM MM2, rev 1.10/0.01, addr 2, iclass 3/1 > kbd2 at ukbd0 > ums0: IBM IBM MM2, rev 1.10/0.01, addr 2, iclass 3/1 > ums0: 3 buttons and Z dir.(Blade center's management console)> Timecounter "TSC" frequency 2400100239 Hz quality 800 > Timecounters tick every 1.000 msecAnd the big timeout (which I think relates to an umass device, referred to in a previous post) happens here ^^^^, with or without SMP and ACPI.> da1 at mpt0 bus 0 target 0 lun 0 > da1: <IBM-ESXS MAY2073RC T107> Fixed Direct Access SCSI-5 device > da1: 300.000MB/s transfers, Tagged Queueing Enabled > da1: 70006MB (143374000 512 byte sectors: 255H 63S/T 8924C) > cd0 at umass-sim1 bus 1 target 0 lun 0 > cd0: <HL-DT-ST RW/DVD GCC-4244N 1.02> Removable CD-ROM SCSI-0 device > cd0: 1.000MB/s transfers > cd0: Attempt to query device size failed: NOT READY, Medium not present > (da0:umass-sim0:0:0:0): got CAM status 0x4 > (da0:umass-sim0:0:0:0): fatal error, failed to attach to device > (da0:umass-sim0:0:0:0): lost device > (da0:umass-sim0:0:0:0): removing device entry > Trying to mount root from ufs:/dev/da1s1a-------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 262 bytes Desc: OpenPGP digital signature Url : http://lists.freebsd.org/pipermail/freebsd-stable/attachments/20070307/e7d57e38/signature.pgp
Do you not have 'device apic' in your config? Scott Ivan Voras wrote:> Continuing my problems with the IBM blade: Booting with ACPI module > enabled (btw. live boot CD with sysinstall doesn't load ACPI, but the > installed system does?) hangs the system somewhere after first USB bus > is found (booting verbose doesn't show any new lines before or after > this step). It appears to be a real hang instead of a timeout because I > left it 30 minutes and it didn't continue. > > Booting without ACPI on the other hand doesn't find all the CPU's :( > > Here's sysctl output: > >> sysctl -a | grep smp > kern.timecounter.smp_tsc: 0 > kern.smp.forward_roundrobin_enabled: 1 > kern.smp.forward_signal_enabled: 1 > kern.smp.cpus: 1 > kern.smp.disabled: 0 > kern.smp.active: 0 > kern.smp.maxcpus: 16 > > > Here's the mptable -dmesg output: > > > > ==============================================================================> > MPTable > > ------------------------------------------------------------------------------- > > MP Floating Pointer Structure: > > location: EBDA > physical address: 0x0009d140 > signature: '_MP_' > length: 16 bytes > version: 1.4 > checksum: 0xfe > mode: Virtual Wire > > ------------------------------------------------------------------------------- > > MP Config Table Header: > > physical address: 0x0009e9b0 > signature: 'PCMP' > base table length: 388 > version: 1.4 > checksum: 0x77 > OEM ID: 'IBM ENSW' > Product ID: 'LEWIS SMP ' > OEM table pointer: 0x00000000 > OEM table size: 0 > entry count: 37 > local APIC address: 0xfee00000 > extended table length: 408 > extended table checksum: 159 > > ------------------------------------------------------------------------------- > > MP Config Base Table Entries: > > -- > Processors: APIC ID Version State Family Model Step > Flags > 0 0x10 BSP, usable 15 1 2 > 0x0301 > 2 0x10 AP, usable 15 1 2 > 0x0301 > 1 0x10 AP, usable 15 1 2 > 0x0301 > 3 0x10 AP, usable 15 1 2 > 0x0301 > -- > Bus: Bus ID Type > 0 PCI > 1 PCI > 2 PCI > 3 PCI > 4 PCI > 5 PCI > 6 PCI > 7 PCI > 8 PCI > 9 ISA > -- > I/O APICs: APIC ID Version State Address > 14 0x11 usable 0xfec00000 > 13 0x11 usable 0xfec02000 > -- > I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# > INT conforms conforms 9 1 14 1 > INT conforms conforms 9 0 14 2 > INT conforms conforms 9 4 14 4 > INT conforms conforms 9 6 14 6 > INT active-hi edge 9 8 14 8 > INT conforms conforms 9 11 14 11 > INT conforms conforms 9 12 14 12 > INT conforms conforms 9 13 14 13 > INT conforms conforms 9 14 14 14 > INT conforms conforms 9 15 14 15 > INT conforms conforms 0 3:A 14 3 > INT conforms conforms 0 3:A 14 3 > INT conforms conforms 0 3:A 14 3 > INT conforms conforms 0 5:A 13 0 > INT conforms conforms 2 4:A 13 1 > INT conforms conforms 2 5:A 13 2 > INT conforms conforms 3 4:A 13 3 > INT conforms conforms 3 5:A 13 4 > INT conforms conforms 3 5:B 13 5 > -- > Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# > NMI conforms conforms 9 0 255 1 > ExtINT conforms conforms 9 0 255 0 > > ------------------------------------------------------------------------------- > > MP Config Extended Table Entries: > > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xa0000 > address range: 0x20000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xf8000000 > address range: 0x2000000 > -- > System Address Space > bus ID: 0 address type: prefetch address > address base: 0xf0000000 > address range: 0x8000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xea000000 > address range: 0x6000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe7000000 > address range: 0x1100000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe5000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe4000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe3000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe2000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe1000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x0 > address range: 0x3b0 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3b0 > address range: 0xc > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3bc > address range: 0x4 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3c0 > address range: 0x20 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3e0 > address range: 0x3c20 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x4000 > address range: 0x1000 > -- > -- > Bus Heirarchy > bus ID: 1 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 2 bus info: 0x00 parent bus ID: 1 > -- > Bus Heirarchy > bus ID: 3 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 4 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 5 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 6 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 7 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 8 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 9 bus info: 0x01 parent bus ID: 0 > -- > Compatibility Bus Address > bus ID: 0 address modifier: add > predefined range: 0x00000000 > -- > Compatibility Bus Address > bus ID: 0 address modifier: add > predefined range: 0x00000001 > > ------------------------------------------------------------------------------- > > dmesg output: > > Copyright (c) 1992-2007 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 6.2-STABLE #0: Wed Mar 7 15:08:28 CET 2007 > root@:/usr/obj/usr/src/sys/SMP > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Dual-Core AMD Opteron(tm) Processor 2216 HE (2400.10-MHz K8-class CPU) > Origin = "AuthenticAMD" Id = 0x40f12 Stepping = 2 > > Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> > Features2=0x2001<SSE3,CX16> > AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!> > AMD Features2=0x1f<LAHF,CMP,SVM,ExtAPIC,CR8> > Cores per package: 2 > real memory = 4815060992 (4592 MB) > avail memory = 4130750464 (3939 MB) > kbd1 at kbdmux0 > ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) > cpu0 on motherboard > pcib0: <Host to PCI bridge> pcibus 0 on motherboard > pci0: <PCI bus> on pcib0 > pcib1: <PCI-PCI bridge> at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > pcib2: <PCI-PCI bridge> at device 13.0 on pci1 > pci2: <PCI bus> on pcib2 > bce0: <Broadcom NetXtreme II BCM5706 1000Base-SX (A2), v0.9.6> mem > 0xea000000-0xebffffff irq 5 at device 4.0 on pci2 > bce0: ASIC ID 0x57060021; Revision (A2); PCI-X 64-bit 133MHz > miibus0: <MII bus> on bce0 > gentbi0: <Generic ten-bit interface> on miibus0 > gentbi0: 1000baseSX, 1000baseSX-FDX, auto > bce0: Ethernet address: 00:14:5e:6d:2d:74 > bce1: <Broadcom NetXtreme II BCM5706 1000Base-SX (A2), v0.9.6> mem > 0xec000000-0xedffffff irq 10 at device 5.0 on pci2 > bce1: ASIC ID 0x57060021; Revision (A2); PCI-X 64-bit 133MHz > miibus1: <MII bus> on bce1 > gentbi1: <Generic ten-bit interface> on miibus1 > gentbi1: 1000baseSX, 1000baseSX-FDX, auto > bce1: Ethernet address: 00:14:5e:b3:2a:38 > isab0: <PCI-ISA bridge> at device 2.2 on pci0 > isa0: <ISA bus> on isab0 > ohci0: <OHCI (generic) USB controller> port 0x3000-0x30ff mem > 0xf9fff000-0xf9ffffff irq 3 at device 3.0 on pci0 > ohci0: [GIANT-LOCKED] > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > ohci1: <OHCI (generic) USB controller> port 0x3100-0x31ff mem > 0xf9ffe000-0xf9ffefff irq 3 at device 3.1 on pci0 > ohci1: [GIANT-LOCKED] > usb1: OHCI version 1.0, legacy support > usb1: <OHCI (generic) USB controller> on ohci1 > usb1: USB revision 1.0 > uhub1: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > ehci0: <EHCI (generic) USB 2.0 controller> port 0x3200-0x32ff mem > 0xf9ffd000-0xf9ffdfff irq 3 at device 3.2 on pci0 > ehci0: [GIANT-LOCKED] > usb2: EHCI version 1.0 > usb2: companion controllers, 2 ports each: usb0 usb1 > usb2: <EHCI (generic) USB 2.0 controller> on ehci0 > usb2: USB revision 2.0 > uhub2: (0x1166) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub2: 4 ports with 4 removable, self powered > uhub3: vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.07, addr 2 > uhub3: multiple transaction translators > uhub3: 2 ports with 2 removable, self powered > uhub4: Cypress Semiconductor 4 Port Hub, class 9/0, rev 1.10/0.01, addr 3 > uhub4: 4 ports with 4 removable, self powered > umass0: TEAC TEAC FD-05PUB, rev 2.00/0.00, addr 4 > umass1: Cypress Semiconductor USB2.0 Storage Device, rev 2.00/0.01, addr 5 > umass1: Get Max Lun not supported (STALLED) > pci0: <display, VGA> at device 5.0 (no driver attached) > pcib3: <PCI-PCI bridge> at device 6.0 on pci0 > pci3: <PCI bus> on pcib3 > mpt0: <LSILogic SAS/SATA Adapter> port 0x4000-0x40ff mem > 0xe8010000-0xe8013fff,0xe8000000-0xe800ffff irq 9 at device 4.0 on pci3 > mpt0: [GIANT-LOCKED] > mpt0: MPI Version=1.5.12.0 > mpt0: mpt_cam_event: 0x16 > mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). > mpt0: mpt_cam_event: 0x12 > mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required). > mpt0: mpt_cam_event: 0x16 > mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). > pci3: <serial bus, Fibre Channel> at device 5.0 (no driver attached) > pci3: <serial bus, Fibre Channel> at device 5.1 (no driver attached) > pcib4: <PCI-PCI bridge> at device 7.0 on pci0 > pci4: <PCI bus> on pcib4 > pcib5: <PCI-PCI bridge> at device 8.0 on pci0 > pci5: <PCI bus> on pcib5 > pcib6: <PCI-PCI bridge> at device 9.0 on pci0 > pci6: <PCI bus> on pcib6 > pcib7: <PCI-PCI bridge> at device 10.0 on pci0 > pci7: <PCI bus> on pcib7 > pcib8: <PCI-PCI bridge> at device 11.0 on pci0 > pci8: <PCI bus> on pcib8 > orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > ppc0: cannot reserve I/O port range > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > ukbd0: IBM IBM MM2, rev 1.10/0.01, addr 2, iclass 3/1 > kbd2 at ukbd0 > ums0: IBM IBM MM2, rev 1.10/0.01, addr 2, iclass 3/1 > ums0: 3 buttons and Z dir. > Timecounter "TSC" frequency 2400100239 Hz quality 800 > Timecounters tick every 1.000 msec > da1 at mpt0 bus 0 target 0 lun 0 > da1: <IBM-ESXS MAY2073RC T107> Fixed Direct Access SCSI-5 device > da1: 300.000MB/s transfers, Tagged Queueing Enabled > da1: 70006MB (143374000 512 byte sectors: 255H 63S/T 8924C) > cd0 at umass-sim1 bus 1 target 0 lun 0 > cd0: <HL-DT-ST RW/DVD GCC-4244N 1.02> Removable CD-ROM SCSI-0 device > cd0: 1.000MB/s transfers > cd0: Attempt to query device size failed: NOT READY, Medium not present > (da0:umass-sim0:0:0:0): got CAM status 0x4 > (da0:umass-sim0:0:0:0): fatal error, failed to attach to device > (da0:umass-sim0:0:0:0): lost device > (da0:umass-sim0:0:0:0): removing device entry > Trying to mount root from ufs:/dev/da1s1a > stray irq7 > bce0: link state changed to DOWN > vlan0: link state changed to DOWN > bce0: link state changed to UP > vlan0: link state changed to UP > stray irq7 > too many stray irq 7's: not logging anymore > mpt0: QUEUE FULL EVENT: Bus 0x00 Target 0x00 Depth 129 > >
Ivan Voras wrote:> Continuing my problems with the IBM blade: Booting with ACPI module > enabled (btw. live boot CD with sysinstall doesn't load ACPI, but the > installed system does?) hangs the system somewhere after first USB bus > is found (booting verbose doesn't show any new lines before or after > this step). It appears to be a real hang instead of a timeout because I > left it 30 minutes and it didn't continue.I've managed to narrow it down. I went on to try 7-CURRENT but accidentally booted the i386 version, which booted without a glitch and recognized all processors, then switched to amd64 version which hanged with or without ACPI, at different places. Since I need it in production, I'll try i386 6.2-release+PAE... -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 262 bytes Desc: OpenPGP digital signature Url : http://lists.freebsd.org/pipermail/freebsd-stable/attachments/20070308/82ebf732/signature.pgp