On Thu, Apr 13, 2006 at 11:01:51PM +0900, SungGON Yi.
wrote:> I am using 6.x on Tyan S2885ANRF board and add one more NIC.
> Device names are bge0 (board lan) and bge1 (additional NIC).
>
> These worked well on FreeBSD 6.0-amd64 stable.
> But when I updated to 6.1-PRERELEASE version, I had below messages and bge0
did not work.
> bge1 worked well as before.
>
> --------------------------------
> bge0: watchdog timeout -- resetting
> --------------------------------
>
> I am using 6.0-RELEASE now.
>
> --------------------------------
> bge0: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem
0xfc6f0000-0xfc6fffff irq 27 at device 8.0 on pci2
> miibus0: <MII bus> on bge0
> brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0
> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
> bge0: Ethernet address: 00:04:76:f3:e8:c9
> bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem
0xfc6e0000-0xfc6effff irq 24 at device 9.0 on pci2
> miibus1: <MII bus> on bge1
> brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1
> brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
> bge1: Ethernet address: 00:e0:81:27:a0:f6
> -----------------------------------
>
>
--------------------------------------------------------------------------------------------------------------------------------
> $ ifconfig
> bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
> inet6 fe80::204:76ff:fef3:e8c9%bge0 prefixlen 64 scopeid 0x1
> inet xxx.xxx.xxx.xxx netmask 0xffffff00 broadcast xxx.xxx.xxx.xxx
> ether 00:04:76:f3:e8:c9
> media: Ethernet autoselect (100baseTX <full-duplex>)
> status: active
> bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
> inet6 fe80::2e0:81ff:fe27:a0f6%bge1 prefixlen 64 scopeid 0x2
> inet 192.168.24.106 netmask 0xffffff00 broadcast 192.168.24.255
> ether 00:e0:81:27:a0:f6
> media: Ethernet autoselect (1000baseTX <full-duplex>)
> status: active
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
> inet6 ::1 prefixlen 128
> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
> inet 127.0.0.1 netmask 0xff000000
> pfsync0: flags=0<> mtu 2020
> pflog0: flags=0<> mtu 33160
> ------------------------------------
>
> SungGON Yi.
> skon@kr.FreeBSD.org
>
> _______________________________________________
> freebsd-stable@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to
"freebsd-stable-unsubscribe@freebsd.org"
I've seen one report about broken onboard bcm5701 asic rev 0x105.
Unfortunatly
i dont have such motherboard to play with. I have PCI nic with same
chip/revision which works fine.
Do you mind of doing binary search on if_bge.c (rev. 1.95 - 1.118) ?
--
Oleg.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 187 bytes
Desc: not available
Url :
http://lists.freebsd.org/pipermail/freebsd-stable/attachments/20060417/e24e368d/attachment.pgp