I need to get a Proliant machine with 2 P3 processors running FreeBSD 6.
I don't know much about the machine, I think it's ML 380 G2 or close to
that, but I have physical access. So far, everything is fine (once the
inability to boot from CD-ROM is circumvented), except one "detail":
horrible write performance on its CISS 5 RAID5 array. I get ~75MB/s
burst (large blocks) reads, and only 5MB/s burst writes. I know how
RAID5 works, but still, this is bad. The machine has been running Linux
before this and performance was Ok - I didn't benchmark it but the
"feeling" when working on it was normal, while on FreeBSD it's
noticably
slow in mixed read/write load.
Is there anything I can try to improve this? In the verbose boot log
there's a line that says the controller supports "simple, performant
and
MEMQ" modes, and the one that's used is "simple" - does this
have any
influence? If so, how to change it?
Thanks!
-------------- next part --------------
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE-p4 #1: Sat Feb 4 15:05:46 UTC 2006
root@duality.cc.fer.hr:/usr/obj/usr/src/sys/DUALITY
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a22000.
Calibrating clock(s) ... i8254 clock: 1193134 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1130453244 Hz
CPU: Intel(R) Pentium(R) III CPU family 1133MHz (1130.45-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 1073725440 (1023 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c28000 - 0x000000003edc3fff, 1041874944 bytes (254364 pages)
avail memory = 1041698816 (993 MB)
MP Configuration Table version 1.4 found at 0xc00fbd2a
APIC: Using the MPTable enumerator.
SMP: Added CPU 3 (BSP)
SMP: Added CPU 0 (AP)
MPTable: <COMPAQ PROLIANT >
APIC ID: physical 0, logical 0:0
APIC ID: physical 3, logical 0:1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 3
cpu1 (AP): APIC ID: 0
bios32: Found BIOS32 Service Directory header at 0xc00ffee0
bios32: Entry = 0xf0000 (c00f0000) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x94
pnpbios: Bad PnP BIOS data checksum
Other BIOS signatures found:
ioapic0: Changing APIC ID to 8
ioapic0: Assuming intbase of 0
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: intpin 0 -> ExtINT (edge, high)
ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
ioapic1: Changing APIC ID to 2
ioapic1: Assuming intbase of 16
ioapic1: intpin 0 -> PCI IRQ 16 (level, low)
ioapic1: intpin 1 -> PCI IRQ 17 (level, low)
ioapic1: intpin 2 -> PCI IRQ 18 (level, low)
ioapic1: intpin 3 -> PCI IRQ 19 (level, low)
ioapic1: intpin 4 -> PCI IRQ 20 (level, low)
ioapic1: intpin 5 -> PCI IRQ 21 (level, low)
ioapic1: intpin 6 -> PCI IRQ 22 (level, low)
ioapic1: intpin 7 -> PCI IRQ 23 (level, low)
ioapic1: intpin 8 -> PCI IRQ 24 (level, low)
ioapic1: intpin 9 -> PCI IRQ 25 (level, low)
ioapic1: intpin 10 -> PCI IRQ 26 (level, low)
ioapic1: intpin 11 -> PCI IRQ 27 (level, low)
ioapic1: intpin 12 -> PCI IRQ 28 (level, low)
ioapic1: intpin 13 -> PCI IRQ 29 (level, low)
ioapic1: intpin 14 -> PCI IRQ 30 (level, low)
ioapic1: intpin 15 -> PCI IRQ 31 (level, low)
ioapic1: intpin 0 bus PCI
ioapic1: intpin 0 trigger: level
ioapic1: intpin 0 polarity: low
ioapic1: intpin 1 bus PCI
ioapic1: intpin 1 trigger: level
ioapic1: intpin 1 polarity: low
ioapic1: intpin 0 bus PCI
ioapic1: intpin 0 trigger: level
ioapic1: intpin 0 polarity: low
ioapic1: intpin 1 bus PCI
ioapic1: intpin 1 trigger: level
ioapic1: intpin 1 polarity: low
ioapic1: intpin 2 bus PCI
ioapic1: intpin 2 trigger: level
ioapic1: intpin 2 polarity: low
ioapic1: intpin 3 bus PCI
ioapic1: intpin 3 trigger: level
ioapic1: intpin 3 polarity: low
ioapic1: intpin 2 bus PCI
ioapic1: intpin 2 trigger: level
ioapic1: intpin 2 polarity: low
ioapic1: intpin 3 bus PCI
ioapic1: intpin 3 trigger: level
ioapic1: intpin 3 polarity: low
ioapic1: intpin 4 bus PCI
ioapic1: intpin 4 trigger: level
ioapic1: intpin 4 polarity: low
ioapic1: intpin 5 bus PCI
ioapic1: intpin 5 trigger: level
ioapic1: intpin 5 polarity: low
ioapic1: intpin 4 bus PCI
ioapic1: intpin 4 trigger: level
ioapic1: intpin 4 polarity: low
ioapic1: intpin 5 bus PCI
ioapic1: intpin 5 trigger: level
ioapic1: intpin 5 polarity: low
ioapic1: intpin 6 bus PCI
ioapic1: intpin 6 trigger: level
ioapic1: intpin 6 polarity: low
ioapic1: intpin 7 bus PCI
ioapic1: intpin 7 trigger: level
ioapic1: intpin 7 polarity: low
ioapic1: intpin 6 bus PCI
ioapic1: intpin 6 trigger: level
ioapic1: intpin 6 polarity: low
ioapic1: intpin 7 bus PCI
ioapic1: intpin 7 trigger: level
ioapic1: intpin 7 polarity: low
ioapic1: intpin 8 bus PCI
ioapic1: intpin 8 trigger: level
ioapic1: intpin 8 polarity: low
ioapic1: intpin 9 bus PCI
ioapic1: intpin 9 trigger: level
ioapic1: intpin 9 polarity: low
ioapic1: intpin 8 bus PCI
ioapic1: intpin 8 trigger: level
ioapic1: intpin 8 polarity: low
ioapic1: intpin 9 bus PCI
ioapic1: intpin 9 trigger: level
ioapic1: intpin 9 polarity: low
ioapic1: intpin 10 bus PCI
ioapic1: intpin 10 trigger: level
ioapic1: intpin 10 polarity: low
ioapic1: intpin 14 bus PCI
ioapic1: intpin 14 trigger: level
ioapic1: intpin 14 polarity: low
ioapic1: intpin 10 bus PCI
ioapic1: intpin 10 trigger: level
ioapic1: intpin 10 polarity: low
ioapic1: intpin 14 bus PCI
ioapic1: intpin 14 trigger: level
ioapic1: intpin 14 polarity: low
ioapic1: intpin 11 bus PCI
ioapic1: intpin 11 trigger: level
ioapic1: intpin 11 polarity: low
ioapic1: intpin 11 bus PCI
ioapic1: intpin 11 trigger: level
ioapic1: intpin 11 polarity: low
ioapic1: intpin 12 bus PCI
ioapic1: intpin 12 trigger: level
ioapic1: intpin 12 polarity: low
ioapic1: intpin 13 bus PCI
ioapic1: intpin 13 trigger: level
ioapic1: intpin 13 polarity: low
ioapic1: intpin 14 bus PCI
ioapic1: intpin 14 trigger: level
ioapic1: intpin 14 polarity: low
ioapic1: intpin 15 bus PCI
ioapic1: intpin 15 trigger: level
ioapic1: intpin 15 polarity: low
ioapic0: intpin 5 bus PCI
ioapic0: intpin 5 trigger: level
ioapic0: intpin 5 polarity: low
ioapic0: intpin 1 bus ISA
ioapic0: intpin 1 trigger: edge
ioapic0: intpin 1 polarity: high
ioapic0: intpin 2 bus ISA
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: high
ioapic0: intpin 3 bus ISA
ioapic0: intpin 3 trigger: edge
ioapic0: intpin 3 polarity: high
ioapic0: intpin 4 bus ISA
ioapic0: intpin 4 trigger: edge
ioapic0: intpin 4 polarity: high
ioapic0: intpin 6 bus ISA
ioapic0: intpin 6 trigger: edge
ioapic0: intpin 6 polarity: high
ioapic0: intpin 7 bus ISA
ioapic0: intpin 7 trigger: edge
ioapic0: intpin 7 polarity: high
ioapic0: intpin 8 bus ISA
ioapic0: intpin 8 trigger: edge
ioapic0: intpin 8 polarity: high
ioapic0: intpin 9 bus ISA
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: low
ioapic0: intpin 12 bus ISA
ioapic0: intpin 12 trigger: edge
ioapic0: intpin 12 polarity: high
ioapic0: intpin 13 bus ISA
ioapic0: intpin 13 trigger: level
ioapic0: intpin 13 polarity: low
ioapic0: intpin 14 bus ISA
ioapic0: intpin 14 trigger: edge
ioapic0: intpin 14 polarity: high
ioapic0: intpin 15 bus ISA
ioapic0: intpin 15 trigger: edge
ioapic0: intpin 15 polarity: high
lapic: Routing ExtINT -> LINT0
lapic: Routing NMI -> LINT1
ioapic1 <Version 1.1> irqs 16-31 on motherboard
ioapic0 <Version 1.1> irqs 0-15 on motherboard
cpu0 BSP:
ID: 0x03000000 VER: 0x00040011 LDR: 0x02000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00000000 err: 0x000100f0 pcm: 0x00010000
mem: <memory>
Pentium Pro MTRR support enabled
nfslock: pseudo-device
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
io: <I/O>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
cpu0 on motherboard
cpu1 on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00091166)
pcibios: BIOS version 2.10
pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1166, dev=0x0009, revid=0x06
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0107, statreg=0x2200, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0009, revid=0x06
bus=0, slot=0, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0107, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x1229, revid=0x08
bus=0, slot=4, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0157, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base c6dff000, size 12, enabled
map[14]: type 4, range 32, base 00002040, size 6, enabled
map[18]: type 1, range 32, base c6c00000, size 20, enabled
pcib0: slot 4 INTA routed to irq 29
found-> vendor=0x1002, dev=0x4752, revid=0x27
bus=0, slot=5, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base c5000000, size 24, enabled
map[14]: type 4, range 32, base 00002400, size 8, enabled
map[18]: type 1, range 32, base c4fff000, size 12, enabled
pcib0: slot 5 INTA routed to irq 30
found-> vendor=0x0e11, dev=0xa0f0, revid=0x00
bus=0, slot=6, func=0
class=08-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0143, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
map[10]: type 4, range 32, base 00001800, size 8, enabled
map[14]: type 1, range 32, base c4ffef00, size 8, enabled
pcib0: slot 6 INTA routed to irq 31
found-> vendor=0x1166, dev=0x0201, revid=0x92
bus=0, slot=15, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0212, revid=0x92
bus=0, slot=15, func=1
class=01-01-8a, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 00002000, size 4, enabled
map[24]: type 4, range 32, base 00000a00, size 2, enabled
found-> vendor=0x1166, dev=0x0220, revid=0x05
bus=0, slot=15, func=2
class=0c-03-10, hdrtype=0x00, mfdev=0
cmdreg=0x0157, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=a, irq=5
map[10]: type 1, range 32, base c4ffd000, size 12, enabled
pcib0: slot 15 INTA routed to irq 5
found-> vendor=0x1166, dev=0x0230, revid=0x00
bus=0, slot=15, func=3
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0004, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
fxp0: <Intel 82559 Pro/100 Ethernet> port 0x2040-0x207f mem
0xc6dff000-0xc6dfffff,0xc6c00000-0xc6cfffff irq 29 at device 4.0 on pci0
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xc6dff000
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 1229 0000 0000 0008
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
fxp0: Ethernet address: 00:50:8b:eb:0e:8c
fxp0: [MPSAFE]
pci0: <display, VGA> at device 5.0 (no driver attached)
pci0: <base peripheral> at device 6.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks CSB5 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x2000-0x200f,0xa00-0xa03 at device 15.1 on
pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x2000
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=02 ostat0=ff ostat1=00
ata0: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0: reset tp2 stat0=00 stat1=00 devices=0x8<ATAPI_SLAVE>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ata1: [MPSAFE]
ohci0: <OHCI (generic) USB controller> mem 0xc4ffd000-0xc4ffdfff irq 5 at
device 15.2 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xc4ffd000
ohci0: (New OHCI DeviceId=0x02201166)
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
pcib2: <MPTable Host-PCI bridge> pcibus 2 on motherboard
pci2: <PCI bus> on pcib2
pci2: physical bus=2
found-> vendor=0x1095, dev=0x0649, revid=0x02
bus=2, slot=2, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0147, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 00003000, size 3, enabled
map[14]: type 4, range 32, base 00003008, size 2, enabled
map[18]: type 4, range 32, base 00003010, size 3, enabled
map[1c]: type 4, range 32, base 00003018, size 2, enabled
map[20]: type 4, range 32, base 00003020, size 4, enabled
pcib2: slot 2 INTA routed to irq 18
found-> vendor=0x14e4, dev=0x1645, revid=0x15
bus=2, slot=3, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0156, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 8 messages, 64 bit
map[10]: type 1, range 64, base c6ff0000, size 16, enabled
pcib2: slot 3 INTA routed to irq 20
found-> vendor=0x0e11, dev=0xb178, revid=0x01
bus=2, slot=5, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0157, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x47 (2130 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D3 current D0
MSI supports 2 messages, 64 bit
map[10]: type 1, range 64, base c6f80000, size 18, enabled
map[18]: type 4, range 32, base 00003400, size 8, enabled
map[1c]: type 3, range 64, base c6efc000, size 14, enabled
pcib2: slot 5 INTA routed to irq 24
atapci1: <CMD 649 UDMA100 controller> port
0x3000-0x3007,0x3008-0x300b,0x3010-0x3017,0x3018-0x301b,0x3020-0x302f irq 18 at
device 2.0 on pci2
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x3020
atapci1: [MPSAFE]
ata2: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x3000
atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0x3008
ata2: reset tp1 mask=03 ostat0=50 ostat1=00
ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2: [MPSAFE]
ata3: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x3010
atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0x3018
ata3: reset tp1 mask=03 ostat0=7f ostat1=7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: stat1=0x7f err=0x7f lsb=0x7f msb=0x7f
ata3: reset tp2 stat0=ff stat1=ff devices=0x0
ata3: [MPSAFE]
bge0: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem
0xc6ff0000-0xc6ffffff irq 20 at device 3.0 on pci2
bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xc6ff0000
miibus1: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus1
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge0: bpf attached
bge0: Ethernet address: 00:04:76:ea:d9:38
bge0: [MPSAFE]
ciss0: <Compaq Smart Array 532> port 0x3400-0x34ff mem
0xc6f80000-0xc6fbffff,0xc6efc000-0xc6efffff irq 24 at device 5.0 on pci2
ciss0: Reserved 0x40000 bytes for rid 0x10 type 3 at 0xc6f80000
ciss0: [GIANT-LOCKED]
ciss0: using 256 of 1024 available commands
ciss0: firmware 1.16
ciss0: 2 SCSI channels
ciss0: signature 'CISS'
ciss0: valence 1
ciss0: supported I/O methods 0xe<simple,performant,MEMQ>
ciss0: active I/O method 0x3<simple>
ciss0: 4G page base 0x00000000
ciss0: interrupt coalesce delay 1000us
ciss0: interrupt coalesce count 16
ciss0: max outstanding commands 1024
ciss0: bus types 0x2<ultra3>
ciss0: server name ''
ciss0: heartbeat 0x10000051
ciss0: 4 physical devices
ciss0: 1 logical drive
ciss0: logical drive (b0t0): RAID 5, 34304MB online
pcib1: <ServerWorks host to PCI bridge> pcibus 1 on motherboard
pci1: <PCI bus> on pcib1
pci1: physical bus=1
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed 0
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xee000-0xeffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
kbd0: atkbd0, generic (0), config:0x0, flags:0x3f0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0045
psm0: failed to reset the aux device.
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: ic_type 90 part_id 73
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
on isa0
fdc0: ic_type 90 part_id 73
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x2021 0x2031 0x2021 0x2021
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x2021 0x2029 0x2021 0x2021
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
ukbd0: vendor 0x0566 product 0x3002, rev 1.10/1.00, addr 2, iclass 3/1
kbd: new array size 4
kbd1 at ukbd0
kbd1: ukbd0, generic (0), config:0x0, flags:0x1d0000
uhid0: vendor 0x0566 product 0x3002, rev 1.10/1.00, addr 2, iclass 3/1
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 66497144 hz
Timecounter "TSC" frequency 1130453244 Hz quality -100
Timecounters tick every 1.000 msec
lo0: bpf attached
ata0-slave: pio=PIO4 wdma=WDMA2 udma=UNSUPPORTED cable=40 wire
acd0: setting PIO4 on ServerWorks CSB5 chip
acd0: <Compaq CRD-8402B/1.03> CDROM drive at ata0 as slave
acd0: read 6875KB/s (6875KB/s), 128KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked, lock protected
acd0: Medium: CD-ROM 120mm data disc
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=80 wire
ad4: setting PIO4 on CMD 649 chip
ad4: setting UDMA100 on CMD 649 chip
ad4: 156334MB <Maxtor 6Y160P0 YAR41BW0> at ata2-master UDMA100
ad4: 320173056 sectors [317632C/16H/63S] 16 sectors/interrupt 1 depth queue
ad4: Silicon Image check3 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
GEOM: new disk ad4
ciss0: command status 0x1 (target status) scsi status 0x2
(probe0:ciss0:0:0:0): error 22
(probe0:ciss0:0:0:0): Unretryable Error
ciss0: command status 0x1 (target status) scsi status 0x2
(probe0:ciss0:0:0:0): error 22
(probe0:ciss0:0:0:0): Unretryable Error
ciss0: command status 0x1 (target status) scsi status 0x2
(probe0:ciss0:0:0:0): error 22
(probe0:ciss0:0:0:0): Unretryable Error
ciss0: command status 0x1 (target status) scsi status 0x2
(probe0:ciss0:0:0:0): error 22
(probe0:ciss0:0:0:0): Unretryable Error
pass0 at ciss0 bus 0 target 0 lun 0
pass0: <COMPAQ RAID 5 VOLUME OK> Fixed Direct Access SCSI-0 device
pass0: 135.168MB/s transfers
da0 at ciss0 bus 0 target 0 lun 0
da0: <COMPAQ RAID 5 VOLUME OK> Fixed Direct Access SCSI-0 device
da0: 135.168MB/s transfers
da0: 34719MB (71106240 512 byte sectors: 255H 32S/T 8714C)
GEOM: new disk da0
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x00000000 VER: 0x00040011 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00000000 err: 0x00010000 pcm: 0x00010000
ioapic1: routing intpin 2 (PCI IRQ 18) to cluster 0
ioapic1: routing intpin 4 (PCI IRQ 20) to cluster 0
ioapic1: routing intpin 8 (PCI IRQ 24) to cluster 0
ioapic1: routing intpin 13 (PCI IRQ 29) to cluster 0
ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
ioapic0: routing intpin 3 (ISA IRQ 3) to cluster 0
ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
ioapic0: routing intpin 5 (PCI IRQ 5) to cluster 0
ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0
ioapic0: routing intpin 7 (ISA IRQ 7) to cluster 0
ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0
ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0
ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0
Trying to mount root from ufs:/dev/da0s1a
start_init: trying /sbin/init
ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding disabled,
default to deny, logging disabled