Joshua Coombs wrote:> Just got a dual Opteron system to play with amd64 builds of FreeBSD.
> Poking around to see how it behaived, I initially tossed FreeBSD 4.11
> on it, and was surprised to see a dump of the scsi controller state at
> the end of the dmesg. Tried 6.0-Rel, both x86 and amd64, same
> behavior. Bumped up to 6-stable from yesterday, same behavior. After
> the dump, the system appears solid, no other errors, so I'm guessing
> it's just a problem with how the card is initialized, FreeBSD corrects
> it and moves on.
>
> Should I be more concerned, or consider it a quirk of the machine?
Oh, you have your Adaptec controller hooked up to one of those Cheetah
10K.7 drives like the ones that are driving us a bit batty at work
(except I'm using ST373207LC [73GB] drives). IIRC, we've been seeing
this SCSI state dump at startup on some of our 5.4-based kernels but not
always. Until recently, I thought the drives were working OK but now
I'm not so sure.
We're trying to track down an infrequent lockup of the SCSI system with
Adaptec AIC7902 Ultra320 controller built-into the motherboard and a
single Seagate ST373207LC drive while running FreeBSD 5.4 on a dual-Xeon
system. We've been running bonnie++ to stress the drive, and we're
having a hard time pinning the failure down to a particular component
(controller or disk) because it's taken bonnie++ running continuously as
many as 6 days straight for the failure to occur. We've tried updating
the firmware on the Seagate drive to ST373207LC from version 3 to 4 and
turning off Packetized transfers in the Adaptec BIOS but we still seem
to be able to make it fail after a while. The next thing I'm tempted to
try changing is the SCSI cable if we still don't have a stable system.
So I'd suggest that you run something like bonnie++ that can stress the
disk & controller for a while, and see whether or not you encounter any
problems...
Good luck!
Guy Helmer>
> Joshua Coombs
>
> Copyright (c) 1992-2005 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD 6.0-RELEASE-p4 #0: Thu Jan 26 15:55:58 EST 2006
> root@testbed.gwi.net:/usr/obj/usr/src/sys/SMP
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: AMD Opteron(tm) Processor 246 (1994.67-MHz K8-class CPU)
> Origin = "AuthenticAMD" Id = 0xf5a Stepping = 10
>
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
>
> AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
> real memory = 1073676288 (1023 MB)
> avail memory = 1024929792 (977 MB)
> ACPI APIC Table: <A M I OEMAPIC >
> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 1
> MADT: Forcing active-low polarity and level trigger for SCI
> ioapic0 <Version 1.1> irqs 0-23 on motherboard
> ioapic1 <Version 1.1> irqs 24-27 on motherboard
> ioapic2 <Version 1.1> irqs 28-31 on motherboard
> acpi0: <A M I OEMXSDT> on motherboard
> acpi0: Power Button (fixed)
> pci_link0: <ACPI PCI Link LNKA> irq 9 on acpi0
> pci_link1: <ACPI PCI Link LNKB> irq 10 on acpi0
> pci_link2: <ACPI PCI Link LNKC> irq 11 on acpi0
> pci_link3: <ACPI PCI Link LNKD> irq 15 on acpi0
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on
acpi0
> cpu0: <ACPI CPU> on acpi0
> acpi_throttle0: <ACPI CPU Throttling> on cpu0
> cpu1: <ACPI CPU> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
> pci3: <ACPI PCI bus> on pcib1
> pci3: <display, VGA> at device 6.0 (no driver attached)
> fxp0: <Intel 82551 Pro/100 Ethernet> port 0xbc00-0xbc3f mem
> 0xfeafb000-0xfeafbfff,0xfeaa0000-0xfeabffff irq 18 at device 8.0 on pci3
> miibus0: <MII bus> on fxp0
> inphy0: <i82555 10/100 media interface> on miibus0
> inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> fxp0: Ethernet address: 00:e0:81:34:64:da
> isab0: <PCI-ISA bridge> at device 7.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <AMD 8111 UDMA133 controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 7.1 on pci0
> ata0: <ATA channel 0> on atapci0
> ata1: <ATA channel 1> on atapci0
> pci0: <serial bus, SMBus> at device 7.2 (no driver attached)
> pci0: <bridge> at device 7.3 (no driver attached)
> pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
> pci2: <ACPI PCI bus> on pcib2
> ahd0: <Adaptec AIC7902 Ultra320 SCSI adapter> port
> 0x8000-0x80ff,0x7800-0x78ff mem 0xfc8fc000-0xfc8fdfff irq 24 at device
> 6.0 on pci2
> ahd0: [GIANT-LOCKED]
> aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
> ahd1: <Adaptec AIC7902 Ultra320 SCSI adapter> port
> 0x8800-0x88ff,0x8400-0x84ff mem 0xfc8fe000-0xfc8fffff irq 25 at device
> 6.1 on pci2
> ahd1: [GIANT-LOCKED]
> aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
> bge0: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem
> 0xfc8b0000-0xfc8bffff,0xfc8a0000-0xfc8affff irq 24 at device 9.0 on pci2
> miibus1: <MII bus> on bge0
> brgphy0: <BCM5704 10/100/1000baseTX PHY> on miibus1
> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
> 1000baseTX-FDX, auto
> bge0: Ethernet address: 00:e0:81:34:65:28
> bge1: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem
> 0xfc8e0000-0xfc8effff,0xfc8d0000-0xfc8dffff irq 25 at device 9.1 on pci2
> miibus2: <MII bus> on bge1
> brgphy1: <BCM5704 10/100/1000baseTX PHY> on miibus2
> brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
> 1000baseTX-FDX, auto
> bge1: Ethernet address: 00:e0:81:34:65:29
> pci0: <base peripheral, interrupt controller> at device 10.1 (no
> driver attached)
> pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
> pci1: <ACPI PCI bus> on pcib3
> pci0: <base peripheral, interrupt controller> at device 11.1 (no
> driver attached)
> acpi_button0: <Power Button> on acpi0
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10
> on acpi0
> sio0: type 16550A
> fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6
drq
> 2 on acpi0
> fdc0: [FAST]
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff on isa0
> ppc0: cannot reserve I/O port range
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
> Timecounters tick every 1.000 msec
> Waiting 5 seconds for SCSI devices to settle
> acd0: CDROM <GCR-8525B/1.02> at ata0-slave PIO4
> ahd0: Invalid Sequencer interrupt occurred.
>>>>>>>>>>>>>>>>>>>
Dump Card State Begins
<<<<<<<<<<<<<<<<<
> ahd0: Dumping Card State at program address 0x23c Mode 0x0
> Card was paused
> INTSTAT[0x0] SELOID[0x1] SELID[0x0] HS_MAILBOX[0x0]
> INTCTL[0x80]:(SWTMINTMASK) SEQINTSTAT[0x0] SAVED_MODE[0x11]
> DFFSTAT[0x33]:(CURRFIFO_NONE|FIFO0FREE|FIFO1FREE)
> SCSISIGI[0x0]:(P_DATAOUT) SCSIPHASE[0x0] SCSIBUS[0x0]
> LASTPHASE[0x1]:(P_DATAOUT|P_BUSFREE) SCSISEQ0[0x0]
> SCSISEQ1[0x12]:(ENAUTOATNP|ENRSELI) SEQCTL0[0x0]
> SEQINTCTL[0x6]:(INTMASK1|INTMASK2)
> SEQ_FLAGS[0x0] SEQ_FLAGS2[0x0] QFREEZE_COUNT[0x2]
> KERNEL_QFREEZE_COUNT[0x2] MK_MESSAGE_SCB[0xff00] MK_MESSAGE_SCSIID[0xff]
> SSTAT0[0x0] SSTAT1[0x0] SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
> SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO) LQISTAT0[0x0]
> LQISTAT1[0x0] LQISTAT2[0x0] LQOSTAT0[0x0] LQOSTAT1[0x0]
> LQOSTAT2[0x0]
>
> SCB Count = 16 CMDS_PENDING = 0 LASTSCB 0xffff CURRSCB 0xe NEXTSCB 0xff40
> qinstart = 28 qinfifonext = 28
> QINFIFO:
> WAITING_TID_QUEUES:
> Pending list:
> Total 0
> Kernel Free SCB list: 15 14 1 2 3 4 5 6 7 8 9 10 11 12 13 0
> Sequencer Complete DMA-inprog list:
> Sequencer Complete list:
> Sequencer DMA-Up and Complete list:
> Sequencer On QFreeze and Complete list:
>
>
> ahd0: FIFO0 Free, LONGJMP == 0x8000, SCB 0xf
>
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS)
>
> SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
> SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
> SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
> HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
>
> ahd0: FIFO1 Free, LONGJMP == 0x8063, SCB 0xe
>
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS)
>
> SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
> SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
> SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
> HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
> LQIN: 0x8 0x0 0x0 0xf 0x0 0x1 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
> 0x0 0x0 0x0 0x0
> ahd0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x42
> ahd0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1
> ahd0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
>
> SIMODE0[0xc]:(ENOVERRUN|ENIOERR)
> CCSCBCTL[0x4]:(CCSCBDIR)
> ahd0: REG0 == 0x8f60, SINDEX = 0x10e, DINDEX = 0x104
> ahd0: SCBPTR == 0xf, SCB_NEXT == 0xff40, SCB_NEXT2 == 0xe
> CDB 12 20 0 80 88 e6
> STACK: 0x237 0x2 0x0 0x0 0x0 0x0 0x0 0x0
> <<<<<<<<<<<<<<<<< Dump
Card State Ends
>>>>>>>>>>>>>>>>>>
> Copied 18 bytes of sense data offset 12: 0x70 0x0 0x6 0x0 0x0 0x0 0x0
> 0xa 0x0 0x0 0x0 0x0 0x29 0x2 0x2 0x0 0x0 0x0
> Copied 18 bytes of sense data offset 12: 0x70 0x0 0x6 0x0 0x0 0x0 0x0
> 0xa 0x0 0x0 0x0 0x0 0x29 0x2 0x2 0x0 0x0 0x0
> SMP: AP CPU #1 Launched!
> da0 at ahd0 bus 0 target 0 lun 0
> da0: <SEAGATE ST336807LC 0C01> Fixed Direct Access SCSI-3 device
> da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged
> Queueing Enabled
> da0: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C)
> da1 at ahd0 bus 0 target 1 lun 0
> da1: <SEAGATE ST336807LC 0C01> Fixed Direct Access SCSI-3 device
> da1: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged
> Queueing Enabled
> da1: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C)
> Trying to mount root from ufs:/dev/da0s1a
>
>
> _______________________________________________
> freebsd-stable@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to
"freebsd-stable-unsubscribe@freebsd.org"
--
Guy Helmer, Ph.D.
Principal System Architect
Palisade Systems, Inc.