Hi,
I'm using the RELEASE-5.4 without any problem, but the RELEASE-6.0 CD
boot stops just before the ad4: message.
This is the output of dmesg on 5.4:
---- begin ----
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.4-RELEASE-p8 #0: Fri Dec 2 16:30:38 BRST 2005
root@me:/usr/obj/usr/src/sys/ME
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2800.81-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf34 Stepping = 4
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs
real memory = 1073414144 (1023 MB)
avail memory = 1045049344 (996 MB)
ACPI APIC Table: <A M I OEMAPIC >
ioapic0: Changing APIC ID to 2
ioapic0 <Version 1.1> irqs 0-23 on motherboard
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <A M I OEMXSDT> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <SiS 655 host to AGP bridge> mem 0xf8000000-0xfbffffff at device
0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <SiS 964 UDMA133 controller> port
0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 2.5 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
pcm0: <SiS 7012> port 0xec00-0xec7f,0xe800-0xe8ff irq 18 at device 2.7
on pci0
pcm0: <Analog Devices AD1888 AC97 Codec>
ohci0: <SiS 5571 USB controller> mem 0xfebfc000-0xfebfcfff irq 20 at
device 3.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <SiS 5571 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <SiS 5571 USB controller> mem 0xfebfd000-0xfebfdfff irq 21 at
device 3.1 on pci0
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <SiS 5571 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
ohci2: <SiS 5571 USB controller> mem 0xfebfe000-0xfebfefff irq 22 at
device 3.2 on pci0
usb2: OHCI version 1.0, legacy support
usb2: SMM does not respond, resetting
usb2: <SiS 5571 USB controller> on ohci2
usb2: USB revision 1.0
uhub2: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 3.3 (no driver attached)
sis0: <SiS 900 10/100BaseTX> port 0xe400-0xe4ff mem
0xfebfb000-0xfebfbfff irq 19 at device 4.0 on pci0
miibus0: <MII bus> on sis0
rlphy0: <RTL8201L 10/100 media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:11:d8:d5:86:54
atapci1: <SiS 964 SATA150 controller> port
0xef90-0xef9f,0xefe0-0xefe3,0xefa8-0xefaf,0xefe4-0xefe7,0xeff0-0xeff7
irq 17 at device 5.0 on pci0
ata2: channel #0 on atapci1
ata3: channel #1 on atapci1
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
fdc0: <floppy drive controller (FDE)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2
on acpi0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
orm0: <ISA Option ROM> at iomem 0xcf000-0xd6fff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ums0: Microsoft Basic Optical Mouse, rev 1.10/0.00, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
Timecounter "TSC" frequency 2800810684 Hz quality 800
Timecounters tick every 10.000 msec
acd0: CDRW <HL-DT-ST GCE-8520B/1.02> at ata1-master PIO4
ad4: 190782MB <ST3200822AS/3.01> [387621/16/63] at ata2-master SATA150
Mounting root from ufs:/dev/ad4s2a
---- end ----
When it boots with 6.0 CD in verbose mode the following messages appears
just before lock-up:
---- begin ----
ata2: reiniting channel ..
ata2: reset tp1 mask=03 ostat0=58 ostat1=58
---- end ----
The only thing I can see after that is the floppy and ide activity leds
lit. Only reset button works after this.
Thanks for any help.
PS.: The same machine boots with RELEASE-5.4 and RELEASE-5.3 CD's
without any problem.
--
Einstein Oliveira einstein@yawl.com.br
___________________________________________________
Yawl Internet Ltda. http://www.yawl.com.br/
Einstein Oliveira <einstein@yawl.com.br> writes:> Hi, > > I'm using the RELEASE-5.4 without any problem, but the RELEASE-6.0 CD > boot stops just before the ad4: message. > > > This is the output of dmesg on 5.4: > > ---- begin ---- > Copyright (c) 1992-2005 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.4-RELEASE-p8 #0: Fri Dec 2 16:30:38 BRST 2005 > root@me:/usr/obj/usr/src/sys/ME > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2800.81-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf34 Stepping = 4 > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > Hyperthreading: 2 logical CPUs > real memory = 1073414144 (1023 MB) > avail memory = 1045049344 (996 MB) > ACPI APIC Table: <A M I OEMAPIC > > ioapic0: Changing APIC ID to 2 > ioapic0 <Version 1.1> irqs 0-23 on motherboard > npx0: <math processor> on motherboard > npx0: INT 16 interface > acpi0: <A M I OEMXSDT> on motherboard > acpi0: Power Button (fixed) > Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 > cpu0: <ACPI CPU> on acpi0 > acpi_throttle0: <ACPI CPU Throttling> on cpu0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > agp0: <SiS 655 host to AGP bridge> mem 0xf8000000-0xfbffffff at device > 0.0 on pci0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > pci1: <display, VGA> at device 0.0 (no driver attached) > isab0: <PCI-ISA bridge> at device 2.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <SiS 964 UDMA133 controller> port > 0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 2.5 on pci0 > ata0: channel #0 on atapci0 > ata1: channel #1 on atapci0 > pcm0: <SiS 7012> port 0xec00-0xec7f,0xe800-0xe8ff irq 18 at device 2.7 > on pci0 > pcm0: <Analog Devices AD1888 AC97 Codec> > ohci0: <SiS 5571 USB controller> mem 0xfebfc000-0xfebfcfff irq 20 at > device 3.0 on pci0 > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <SiS 5571 USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 3 ports with 3 removable, self powered > ohci1: <SiS 5571 USB controller> mem 0xfebfd000-0xfebfdfff irq 21 at > device 3.1 on pci0 > usb1: OHCI version 1.0, legacy support > usb1: SMM does not respond, resetting > usb1: <SiS 5571 USB controller> on ohci1 > usb1: USB revision 1.0 > uhub1: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 3 ports with 3 removable, self powered > ohci2: <SiS 5571 USB controller> mem 0xfebfe000-0xfebfefff irq 22 at > device 3.2 on pci0 > usb2: OHCI version 1.0, legacy support > usb2: SMM does not respond, resetting > usb2: <SiS 5571 USB controller> on ohci2 > usb2: USB revision 1.0 > uhub2: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub2: 2 ports with 2 removable, self powered > pci0: <serial bus, USB> at device 3.3 (no driver attached) > sis0: <SiS 900 10/100BaseTX> port 0xe400-0xe4ff mem > 0xfebfb000-0xfebfbfff irq 19 at device 4.0 on pci0 > miibus0: <MII bus> on sis0 > rlphy0: <RTL8201L 10/100 media interface> on miibus0 > rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > sis0: Ethernet address: 00:11:d8:d5:86:54 > atapci1: <SiS 964 SATA150 controller> port > 0xef90-0xef9f,0xefe0-0xefe3,0xefa8-0xefaf,0xefe4-0xefe7,0xeff0-0xeff7 > irq 17 at device 5.0 on pci0 > ata2: channel #0 on atapci1 > ata3: channel #1 on atapci1 > acpi_button0: <Power Button> on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > fdc0: <floppy drive controller (FDE)> port 0x3f7,0x3f0-0x3f5 irq 6 drq > 2 on acpi0 > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0 > ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode > ppbus0: <Parallel port bus> on ppc0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 > on acpi0 > sio0: type 16550A > orm0: <ISA Option ROM> at iomem 0xcf000-0xd6fff on isa0 > pmtimer0 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > ums0: Microsoft Basic Optical Mouse, rev 1.10/0.00, addr 2, iclass 3/1 > ums0: 3 buttons and Z dir. > Timecounter "TSC" frequency 2800810684 Hz quality 800 > Timecounters tick every 10.000 msec > acd0: CDRW <HL-DT-ST GCE-8520B/1.02> at ata1-master PIO4 > ad4: 190782MB <ST3200822AS/3.01> [387621/16/63] at ata2-master SATA150 > Mounting root from ufs:/dev/ad4s2a > ---- end ---- > > > When it boots with 6.0 CD in verbose mode the following messages > appears just before lock-up: > > ---- begin ---- > ata2: reiniting channel .. > ata2: reset tp1 mask=03 ostat0=58 ostat1=58 > ---- end ---- > > The only thing I can see after that is the floppy and ide activity > leds lit. Only reset button works after this.Does it boot in "safe mode"?