Richard Lee
2005-Nov-13 09:59 UTC
Second SATA drive not detected on 6.0-Release and 6.0-Stable.
I have two SATA drives (ad4 and ad6 with static id), but the second one is simply not detected in 6.0. ========================================================================= Before, I was running RELENG_5.4 and was getting: Nov 5 13:57:51 minawa kernel: atapci0: <SiS 964 UDMA133 controller> port 0xf000-0xf00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 2.5 on pci0 Nov 5 13:57:51 minawa kernel: ata0: channel #0 on atapci0 Nov 5 13:57:51 minawa kernel: ata1: channel #1 on atapci0 Nov 5 13:57:51 minawa kernel: atapci1: <SiS 964 SATA150 controller> port 0xb800-0xb80f,0xb400-0xb403,0xb000-0xb007,0xac00-0xac03,0xa800-0xa807 irq 17 at device 5.0 on pci0 Nov 5 13:57:51 minawa kernel: ata2: channel #0 on atapci1 Nov 5 13:57:51 minawa kernel: ata3: channel #1 on atapci1 Nov 5 13:57:51 minawa kernel: acd0: DVDR <NEC DVD RW ND-3540A/1.6W> at ata0-master UDMA33 Nov 5 13:57:51 minawa kernel: ad4: 76318MB <ST380817AS/3.42> [155058/16/63] at ata2-master SATA150 Nov 5 13:57:51 minawa kernel: ad6: 152627MB <ST3160827AS/3.42> [310101/16/63] at ata3-master SATA150 Nov 5 13:57:51 minawa kernel: cd0 at ata0 bus 0 target 0 lun 0 After the upgrade, I get: Nov 13 05:17:14 minawa kernel: atapci0: <SiS 964 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 2.5 on pci0 Nov 13 05:17:14 minawa kernel: ata0: <ATA channel 0> on atapci0 Nov 13 05:17:14 minawa kernel: ata1: <ATA channel 1> on atapci0 Nov 13 05:17:14 minawa kernel: atapci1: <SiS 180 SATA150 controller> port 0xa800-0xa807,0xac00-0xac03,0xb000-0xb007,0xb400-0xb403,0xb800-0xb80f,0xbc00-0xbc7f irq 17 at device 5.0 on pci0 Nov 13 05:17:14 minawa kernel: ata2: <ATA channel 0> on atapci1 Nov 13 05:17:14 minawa kernel: ata3: <ATA channel 1> on atapci1 Nov 13 05:17:14 minawa kernel: acd0: DVDR <NEC DVD RW ND-3540A/1.6W> at ata0-master UDMA33 Nov 13 05:17:14 minawa kernel: ad4: 76318MB <Seagate ST380817AS 3.42> at ata2-master SATA150 Nov 13 05:17:14 minawa kernel: cd0 at ata0 bus 0 target 0 lun 0 # atacontrol info ata2 Master: ad4 <ST380817AS/3.42> Serial ATA v1.0 Slave: no device present # atacontrol info ata3 Master: no device present <========= SHOULD BE HERE! Slave: no device present ========================================================================= When I swapped the drive connections, it still only detected whatever is connected to ata2, but not to ata3. Windows sees both just fine, so does the 5.4-Release CD-ROM. I'm sure there's nothing wrong with the hardware. I even downloaded 6.0R ISO image and booted, and there too, the second disk is not detected. I tried disabling ATA_STATIC_ID, which causes ad4 to become ad0, but no other effect. I have no IDE hard drives, only two SATA drives. I don't consider this set up to be anything unusual: Giga-Byte GA-K8S760M (SIS760/964) with 2GB memory, Sempron64 1.8GHz 256kL2. No RAID (BIOS setting for RAID/Non-RAID didn't make any difference, either). I also tried 6.0-Stable (2005-11-12) and it's the same problem. --rich
Giovanni P. Tirloni
2005-Nov-14 03:13 UTC
Second SATA drive not detected on 6.0-Release and 6.0-Stable.
Richard Lee wrote:> I even downloaded 6.0R ISO image and booted, and there too, the second disk is > not detected. I tried disabling ATA_STATIC_ID, which causes ad4 to become > ad0, but no other effect. I have no IDE hard drives, only two SATA drives. I > don't consider this set up to be anything unusual: Giga-Byte GA-K8S760M > (SIS760/964) with 2GB memory, Sempron64 1.8GHz 256kL2. No RAID (BIOS setting > for RAID/Non-RAID didn't make any difference, either).I tried 6.0-RELEASE only and have the same problem. It's the same SiS chipset here. I've tried 6.0 with other chipsets (Intel/VIA) and that doesn't happen. Also with IDE disks it works just fine too. -- Giovanni P. Tirloni http://blog.tirloni.org