On Thu, 12 May 2005, jmc wrote:
> I've got 5.4 amd64 installed on an Opteron server and I cannot get it
to
> reliably transmit packets larger than 80 bytes using the bge driver (on a
> BCM5703 NIC). It receives large packets without any problem, but it just
> won't transmit them. (I can tcpdump all day long without a problem -
big and
> small packets.)
>
> For example, I can "ping -s 38 <ip>" and it works fine. But
if I try "ping
> -s 39 <ip>" (or any size larger than 38) it does not work. A 38
byte ping
> creates an 80 byte Ethernet packet.
Random guesses:
1. Make sure your switch agrees with the speed and duplex setting.
Auto-neg problems are common.
2. Replace the cable.
3. Back-to-back two systems and try to reproduce.
>
> Here's the bge0 info from dmesg:
>
> bge0: <Broadcom BCM5703X Gigabit Ethernet, ASIC rev. 0x1100> mem
> 0xf7ef0000-0xf7
> efffff irq 24 at device 1.0 on pci3
> bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xf7ef0000
> miibus0: <MII bus> on bge0
> brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0
> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
> 1000baseTX
> -FDX, auto
> bge0: bpf attached
> bge0: Ethernet address: 00:11:85:fd:8f:f9
> bge0: [MPSAFE]
>
> Here's ifconfig for bge0:
>
> bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> options=1a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
> inet 16.100.240.165 <http://16.100.240.165> netmask 0xfffffc00
broadcast
> 16.100.243.255 <http://16.100.243.255>
> inet6 fe80::211:85ff:fefd:8ff9%bge0 prefixlen 64 scopeid 0x1
> ether 00:11:85:fd:8f:f9
> media: Ethernet autoselect (1000baseTX <full-duplex>)
> status: active
>
> Much to my dismay, I've found that if I use the -l option (preload) for
> ping, I get some large packets through:
>
> ninox# ping -l10 -c10 -s200 16.100.240.1 <http://16.100.240.1>
> PING 16.100.240.1 <http://16.100.240.1> (16.100.240.1
<http://16.100.240.1>):
> 200 data bytes
> 208 bytes from 16.100.240.1 <http://16.100.240.1>: icmp_seq=2 ttl=128
time> 1.025 ms
> 208 bytes from 16.100.240.1 <http://16.100.240.1>: icmp_seq=3 ttl=128
time> 1.306 ms
> 208 bytes from 16.100.240.1 <http://16.100.240.1>: icmp_seq=4 ttl=128
time> 1.593 ms
> 208 bytes from 16.100.240.1 <http://16.100.240.1>: icmp_seq=5 ttl=128
time> 2.026 ms
> 208 bytes from 16.100.240.1 <http://16.100.240.1>: icmp_seq=6 ttl=128
time> 2.314 ms
> 208 bytes from 16.100.240.1 <http://16.100.240.1>: icmp_seq=7 ttl=128
time> 2.746 ms
> 208 bytes from 16.100.240.1 <http://16.100.240.1>: icmp_seq=8 ttl=128
time> 3.034 ms
> 208 bytes from 16.100.240.1 <http://16.100.240.1>: icmp_seq=9 ttl=128
time> 3.468 ms
>
> --- 16.100.240.1 <http://16.100.240.1> ping statistics ---
> 10 packets transmitted, 8 packets received, 20% packet loss
> round-trip min/avg/max/stddev = 1.025/2.189/3.468/0.806 ms
>
> Has anyone else ever seen a problem like this? Any suggestions on where to
> poke around for a solution?
>
> Thanks,
> John
> _______________________________________________
> freebsd-stable@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to
"freebsd-stable-unsubscribe@freebsd.org"
>
--
Doug White | FreeBSD: The Power to Serve
dwhite@gumbysoft.com | www.FreeBSD.org