freebsd stable - May 2005 - RAID 1 with Adaptec SATA 1210SA + FreeBSD 5.4 + ata mkIII OK

Hi Soeren,

I have to thank you for the work you put in the ata driver.
After patching the 5.4 sources with the new ata mkIII
(http://people.freebsd.org/~sos/ATA)
I am able to use the RAID 1 with my Adaptec SATA 1210SA.

The dmesg (the Adaptec is recognized as Sil 3112 SATA150):

FreeBSD 5.4-RELEASE #2: Mon May  9 12:07:51 EEST 2005
     ardelean at quasar.physics.uvt.ro:/usr/obj/usr/src/sys/QUASAR
...
atapci1: <Promise PDC20267 UDMA100 controller> port 
0xa400-0xa43f,0xa000-0xa003,0x9c00-0x9c07,0x9800-0x9803,0x9400-0x9407 mem 0
d5100000-0xd511ffff irq 10 at device 9.0 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
... 
atapci2: <SiI 3112 SATA150 controller> port 
0xbc00-0xbc0f,0xb800-0xb803,0xb400-0xb407,0xb000-0xb003,0xac00-0xac07 mem 
0xd512100-0xd51211ff irq 5 at device 13.0 on pci0
ata4: <ATA channel 0> on atapci2
ata4: SATA connect ready time=0ms
ata5: <ATA channel 1> on atapci2
ata5: SATA connect ready time=0ms
...
ad4: 38166MB <Seagate ST340014A 3.04> at ata2-master UDMA100
ad6: 38166MB <Seagate ST340014A 3.04> at ata3-master UDMA100
ad8: 190782MB <SAMSUNG SP2004C VM100-31> at ata4-master SATA150
ad10: 190782MB <SAMSUNG SP2004C VM100-31> at ata5-master SATA150
Waiting 5 seconds for SCSI devices to settle
ATA PseudoRAID loaded
ar0: 38166MB <Promise Fasttrak RAID1 array> status: READY
ar0: disk0 READY (master) using ad6 at ata3-master
ar0: disk1 READY (mirror) using ad4 at ata2-master
ar1: 190782MB <Adaptec HostRAID RAID1 array> status: READY
ar1: disk0 READY (master) using ad8 at ata4-master
ar1: disk1 READY (mirror) using ad10 at ata5-master
Mounting root from ufs:/dev/ar0s1a

Is it possible to MFC the ata mkIII from -current to 5-STABLE ?

Once again thank you!

G. Ardelean

West Univ. Of Timisoara
Dept. of Theoretical and Computational Physics
V. Parvan No.4, Ro-300223, Timisoara, ROMANIA
Tel: +40-(0)256-494068 Ext. 203, 201, 108 | Fax: +40-(0)256-496088
Email: ardelean at physics.uvt.ro

Copyright 1999-2005 Gheorghe Ardelean.  All rights reserved.
Duplication and redistribution prohibited without consent of the author.

Gheorghe Ardelean wrote:
> 
> Hi Soeren,
> 
> I have to thank you for the work you put in the ata driver.
Thanks!
> After patching the 5.4 sources with the new ata mkIII
> (http://people.freebsd.org/~sos/ATA)
> I am able to use the RAID 1 with my Adaptec SATA 1210SA.
Good :) let me know if you run into problems with it!

-- 

-S?ren