Hi Generally Beautiful and Possibly Helpful People,
Since version 4.9 and currently running version 4.10-RELEASE-p2,
both i386, reboot causes only a hang up after system has been up
for few hours. I did not have stuck-on-reboot problem somewhere
between 4.6 & 4.8. Boot sequence hangs after following lines have
been printed...
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
isa_probe_children: probing PnP devices
Some relevant information...
- Current dmesg (attached also) ...
http://parv.holy.cow/parv/comp/unix/err/dmesg/dmesg-4.10-p2-2004.06.30.17.33.59
- Current kernel configuration ...
http://parv.holy.cow/parv/comp/unix/cf/FreeBSD/KERNCONF
- General overview of Dell Inspiron 5000e (laptop)...
http://parv.holy.cow/parv/comp/unix/FreeBSD/delli5000e.xhtmls
Is there any solution for the situation of "stuck on reboot"?
- Parv
--
-------------- next part --------------
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.10-RELEASE-p2 #7: Sat Aug 28 12:06:36 EDT 2004
root@moo.holy.cow:/misc/src-4.10/sys/BOVINE
Calibrating clock(s) ... TSC clock: 696963716 Hz, i8254 clock: 1193170 Hz
Timecounter "i8254" frequency 1193170 Hz
CPU: Intel Pentium III (696.96-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 402587648 (393152K bytes)
Physical memory chunk(s):
0x000001000 - 0x00009efff, 647168 bytes (158 pages)
0x000422000 - 0x017fe7fff, 398221312 bytes (97222 pages)
avail memory = 387149824 (378076K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f7210
bios32: Entry = 0xfd890 (c00fd890) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x11e
pnpbios: Found PnP BIOS data at 0xc00f7240
pnpbios: Entry = f0000:a600 Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
ACPI: 000f71d0
Preloaded elf kernel "kernel" at 0xc03fb000.
Pentium Pro MTRR support enabled
Creating DISK md0
md0: Malloc disk
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003904
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
Using $PIR table, 7 entries at 0xc00fdf50
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7190, revid=0x03
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base e0000000, size 26
found-> vendor=0x8086, dev=0x7191, revid=0x03
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x104c, dev=0xac1c, revid=0x01
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=255
found-> vendor=0x104c, dev=0xac1c, revid=0x01
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=255
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 00001050, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=5
map[20]: type 1, range 32, base 00001060, size 5
found-> vendor=0x8086, dev=0x7113, revid=0x03
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 00001040, size 4
found-> vendor=0x125d, dev=0x1978, revid=0x10
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 00001400, size 8
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x1002, dev=0x4c46, revid=0x02
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base f8000000, size 26
map[14]: type 1, range 32, base 00002000, size 8
map[18]: type 1, range 32, base f4000000, size 14
pci1: <PCI bus> on pcib1
pci1: <ATI model 4c46 graphics accelerator> (vendor=0x1002, dev=0x4c46) at
0.0 irq 11
pci_cfgintr_linked: linked (60) to hard-routed irq 11
pci_cfgintr: 0:4 INTA routed to irq 11
pcic0: <TI PCI-1225 PCI-CardBus Bridge> irq 11 at device 4.0 on pci0
pcic0: PCI Memory allocated: 0x88000000
pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][FUNC pci
int + CSC serial isa irq]
pcic0: PCI Configuration space:
0x00: 0xac1c104c 0x02100007 0x06070001 0x00820000
0x10: 0x88000000 0x020000a0 0x20000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x0760010b
0x40: 0x00cc1028 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x20449060 0x00000000 0x00000000 0x01021c72
0x90: 0x606682c0 0x00000000 0x00000000 0x00000000
0xa0: 0x7e210001 0x00800000 0x00000000 0x0000001f
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pci_cfgintr_linked: linked (60) to hard-routed irq 11
pci_cfgintr: 0:4 INTA routed to irq 11
pcic1: <TI PCI-1225 PCI-CardBus Bridge> irq 11 at device 4.1 on pci0
pcic1: PCI Memory allocated: 0x88001000
pcic1: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][FUNC pci
int + CSC serial isa irq]
using shared irq11.
pcic1: PCI Configuration space:
0x00: 0xac1c104c 0x02100007 0x06070001 0x00820000
0x10: 0x88001000 0x020000a0 0x20000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x0760010b
0x40: 0x00cc1028 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x20449060 0x00000000 0x00000000 0x01021c72
0x90: 0x606682c0 0x00000000 0x00000000 0x00000000
0xa0: 0x7e210001 0x00800000 0x00000000 0x0000001f
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard1: <PC Card 16-bit bus (classic)> on pcic1
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x1050-0x105f at device 7.1
on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1050
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1058
ata1: mask=03 ostat0=25 ostat2=25
ata1-master: ATAPI 25 25
ata1-slave: ATAPI 25 25
ata1: mask=03 stat0=25 stat1=25
ata1-master: ATA 25 25
ata1-slave: ATA 25 25
ata1: devices=00
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1060-0x107f irq 5
at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
chip1: <Intel 82371AB Power management controller> port 0x1040-0x104f at
device 7.3 on pci0
pcm0: <ESS Technology Maestro-2E> port 0x1400-0x14ff irq 5 at device 8.0
on pci0
setmap (1000, 4000), nseg=1, error=0
pcm0: Maestro DMA base: 0x1000
pcm0: <SigmaTel STAC9721/23 AC97 Codec (id = 0x83847609)>
pcm0: Codec features 18 bit DAC, 18 bit ADC, 5 bit master volume, SigmaTel 3D
Enhancement
pcm0: Primary codec extended features AMAP
using shared irq5.
setmap (5000, 4000), nseg=1, error=0
pcm0: pch[0].offset = 0x4000
setmap (9000, 4000), nseg=1, error=0
pcm0: pch[1].offset = 0x8000
setmap (d000, 4000), nseg=1, error=0
pcm0: pch[2].offset = 0xc000
setmap (11000, 4000), nseg=1, error=0
pcm0: pch[3].offset = 0x10000
pcic-: pcic0 exists, using next available unit number
pcic-: pcic1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xcefff,0xdc000-0xdffff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on this adapter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 c3
b4 1f 00 4f 0d 0e 00 00 07 30 91 87 8f 28 1f 8f
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 0e 00 10 01 03 00 02 a3 5f 4f 50 82 55 81
bf 1f 00 4d 0b 0c 00 00 00 00 83 85 5d 28 1f 63
ba a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 08 00 0f 00 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 c3
b4 1f 00 4f 0d 0e 00 00 07 30 91 87 8f 28 1f 8f
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <8 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic2 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic3: not probed (disabled)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio2: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/7 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03feef3f 0..1022=1023 cylinders, 0..239=240 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 68c060, tty 6318b2, net 6718b2
Linux ELF exec handler installed
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.31 initialized. Default = block all, Logging = enabled
ad0: success setting UDMA2 on Intel chip
Creating DISK ad0
ar: FreeBSD check1 failed
ad0: <FUJITSU MHT2060AH/006C> ATA-6 disk at ata0-master
ad0: 57231MB (117210240 sectors), 116280 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
Mounting root from ufs:/dev/ad0s3a
ad0s1: type 0xb, start 63, end = 2101679, size 2101617 : OK
ad0s3: type 0xa5, start 13638240, end = 81572399, size 67934160 : OK
ad0s4: type 0xf, start 81572400, end = 117210239, size 35637840 : OK
ad0s5: type 0xb, start 81572463, end = 113037119, size 31464657
ad0s5: C/H/S start 1023/1/1 (15467823) != start 81572463: invalid
ad0<extended>: type 0x5, start 113037120, end = 117210239, size 4173120
ad0<extended>: C/H/S start 1023/0/1 (15467760) != start 113037120: invalid
ad0s6: type 0x6, start 113037183, end = 117210239, size 4173057
ad0s6: C/H/S start 1023/1/1 (15467823) != start 113037183: invalid
start_init: trying /sbin/init
dumpon: crash dumps to /dev/ad0s3b (116, 262145)
swapon: adding /dev/ad0s3b as swap device
Automatic boot in progress...
/dev/ad0s3a:
FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s3a:
clean, 12802 free
(42 frags, 1595 blocks, 0.1% fragmentation)
/dev/ad0s3e:
FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s3e:
clean, 198931 free
(4459 frags, 24309 blocks, 1.5% fragmentation)
/dev/ad0s3f:
FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s3f:
clean, 234974 free
(118 frags, 29357 blocks, 0.0% fragmentation)
/dev/ad0s3h:
FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s3h:
clean, 9868617 free
(67233 frags, 1225173 blocks, 0.5% fragmentation)
/dev/ad0s3g:
FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s3g:
clean, 1083754 free
(850 frags, 135363 blocks, 0.1% fragmentation)
Warning: Block size and bytes per inode restrict cylinders per group to 89.
Setup PC-CARD:
memory
beep
pccardd
.
Doing initial network setup:
hostname
.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
inet 127.0.0.2 netmask 0xff000000
inet 127.0.0.3 netmask 0xff000000
Additional routing options:
TCP keepalive=YES
.
Routing daemons:
.
Additional daemons:
syslogd
.
Checking for core dump:
savecore: no core dump
Doing additional network setup:
.
Starting final network daemons:
.
ELF ldconfig path: /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib
a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /usr/X11R6/lib/aout
/usr/local/lib/aout
Starting standard daemons:
inetd
cron
printer
sshd
.
Initial rc.i386 initialization:
.
Configuring syscons:
blanktime
moused
.
Additional ABI support:
.
Local package initialization:
apache
(skipping cyrus_pwcheck.sh, not executable)
(skipping ipf.sh, not executable)
(skipping junkbuster.sh, not executable)
postfix/postfix-script: starting the Postfix mail system
rxstack listening on port: 5757
Starting Regina Stack
(skipping saslauthd1.sh, not executable)
.
Additional TCP options:
.
Sat Aug 28 19:21:31 EDT 2004
Aug 28 19:22:00 moo su: parv to root on /dev/ttyp9
pcic1: Event mask 0x2
pcic1: Event mask 0x2
pcic1: Event mask 0x6
pcic1: Autodetected 5.0V card
pccard: card inserted, slot 1
pcic1: reset 1 int is 10 stat is 7f
pcic1: reset 2 pcic1: Event mask 0x9
int is 70 stat is 5f
pcic1: reset 3 int is 70 stat is 7f
Aug 28 19:22:16 moo pccardd[56]: Card "3Com
Corporation"("3C589D") [TP/BNC LAN Card Ver. 2a] [000002] matched
"3Com Corporation" ("/3C589/") [(null)] [(null)]
pccard1: Assigning ep0: io 0x240-0x24f irq 11 flags 0x0
pcic: I/O win 0 flags 17 240-24f
ep0: Forcing IRQ to 11
pcic: I/O win 0 flags 7 240-24f
ep0: <3Com Etherlink III 3C589> at port 0x240-0x24f irq 11 slot 1 on
pccard1
pcic: I/O win 0 flags 17 240-24f
ep0: Forcing IRQ to 11
ep0: Ethernet address 00:10:4b:de:6e:eb
bpf: ep0 attached
Aug 28 19:22:21 moo pccardd[56]: ep0: 3Com Corporation (/3C589/) inserted.