tried chan_sip/udp + pjsip/tcp but the same problem sip.conf [general] udpbindport=5060 udpbindaddr=0.0.0.0 tcpenable=no tlsenable=no pjsip.conf [transport-tcp] type = transport bind = 2.2.2.2:5070 protocol = tcp Loading res_pjsip.so. [Nov 25 16:21:04] ERROR[5528]: res_pjsip/config_transport.c:664 transport_apply: Transport 'transport-tcp' could not be started: Cannot assign requested address [Nov 25 16:21:04] ERROR[5528]: res_sorcery_config.c:420 sorcery_config_internal_load: Could not create an object of type 'transport' with id 'transport-tcp' from configuration file 'pjsip.conf' anybody know if its possible preload pjsip before chan_sip? (tried preload= but its complicated. a lot of dependecies) its Asterisk 13 current Marek Dne 25/11/2020 v 14:55 marek napsal(a):> hi, > > i want gradually migrate to pjsip > > i have 2 network interfaces with a lot of endpoints on both (both UDP) > eth0 1.1.1.1 > eth1 2.2.2.2 > > i want start migrate endpoints to pjsip on 2.2.2.2:5070 > > but configuration like this is not possible > > sip.conf > > [general] > bindaddr = 0.0.0.0 > bindport = 5060 > > pjsip.conf > [udp] > type = transport > bind = 2.2.2.2:5070 > protocol = udp > > > [Nov 25 14:44:18] ERROR[3442]: res_pjsip/config_transport.c:664 > transport_apply: Transport 'udp' could not be started: Cannot assign > requested address > > [Nov 25 14:44:18] ERROR[3442]: res_sorcery_config.c:420 > sorcery_config_internal_load: Could not create an object of type > 'transport' with id 'udp' from configuration file > > > is there some other way? > > thanks > > Marek > >
On Wed, Nov 25, 2020 at 11:24 AM marek <cervajs64 at gmail.com> wrote:> tried chan_sip/udp + pjsip/tcp > > but the same problem > > sip.conf > > [general] > udpbindport=5060 > udpbindaddr=0.0.0.0 > tcpenable=no > tlsenable=no > > pjsip.conf > [transport-tcp] > type = transport > bind = 2.2.2.2:5070 > protocol = tcp > > Loading res_pjsip.so. > [Nov 25 16:21:04] ERROR[5528]: res_pjsip/config_transport.c:664 > transport_apply: Transport 'transport-tcp' could not be started: Cannot > assign requested address > [Nov 25 16:21:04] ERROR[5528]: res_sorcery_config.c:420 > sorcery_config_internal_load: Could not create an object of type > 'transport' with id 'transport-tcp' from configuration file 'pjsip.conf' > > anybody know if its possible preload pjsip before chan_sip? (tried > preload= but its complicated. a lot of dependecies) >You're assuming that the problem is an interaction between chan_sip and chan_pjsip. If you don't load chan_sip at all, does the problem still occur? If so then chan_sip isn't the problem but something most likely system level - since the system stated that PJSIP could not use the configured address. -- Joshua C. Colp Asterisk Technical Lead Sangoma Technologies Check us out at www.sangoma.com and www.asterisk.org -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20201125/9a1d249b/attachment.html>