Nick Ellson
2006-Sep-28 12:47 UTC
[asterisk-users] Asterisk lockup and boot error after one day?
I had installed a X100P clone just as a quick trial at real analog access and my system would not boot successfully (error below) but I figured it was just a bad card and at $20 I didn't care much. Now I have a 12 port card using the FXO/FXS modules, and installed it Tuesday. It booted great, got the drivers working and even made a few calls in each direction. Over last night the system locked up hard (IE: Dark screen, num-lock or caps lock won't toggle) After a hard reset, I see a lot of "Dazed and Confused....) messages and then it hangs, but after a second boot and all those errors again it makes it to run level 3 and I can shell in and grab "dmesg" before it locks up. Take the card out, it's all happy again. Ok, why did I ask Asterisk-Users? I have not seen this until I tried these two telecom based cards and I want to know if this is something that happens using cards or zaptel/zapata drivers, or should I be looking at a hardware specific forum? (IE: Any Asterisk users have this happen?) <snip large section of normal boot process, no errors> [17179587.012000] Zapata Telephony Interface Registered on major 196 [17179587.012000] Zaptel Version: 1.2.8 Echo Canceller: KB1 [17179587.052000] ACPI: PCI Interrupt 0000:05:05.0[A] -> GSI 20 (level, low) -> IRQ 20 [17179587.052000] OpenVox A1200P version: 1.1 [17179587.052000] OpenVox A1200P passed register test [17179587.128000] evbug.c: Connected device: "PC Speaker", isa0061/input0 [17179587.128000] evbug.c: Connected device: "ImPS/2 Logitech Wheel Mouse", isa0060/serio1/input0 [17179587.128000] evbug.c: Connected device: "AT Translated Set 2 keyboard", isa0060/serio0/input0 [17179587.952000] Module 0: Installed -- AUTO FXO (FCC mode) [17179589.104000] Module 1: Installed -- AUTO FXS/DPO [17179589.104000] Module 2: Not installed [17179589.104000] Module 3: Not installed [17179589.104000] Module 4: Not installed [17179589.104000] Module 5: Not installed [17179589.104000] Module 6: Not installed [17179589.104000] Module 7: Not installed [17179589.104000] Module 8: Not installed [17179589.104000] Module 9: Not installed [17179589.104000] Module 10: Not installed [17179589.104000] Module 11: Not installed [17179589.108000] Found a OpenVox A1200P: Version 1.1 (2 modules) [17179589.108000] buffer re-sync occur from 0 to 2 [17179589.268000] hw_random hardware driver 1.0.0 loaded [17179591.232000] ipmi message handler version 39.0 [17179591.240000] IPMI Watchdog: driver initialized [17179591.248000] ipmi device interface [17179591.388000] IPMI SMB Interface driver [17179591.388000] ipmi_smb: DMI specifies SSIF @ 0x42, slave address 0x84 [17179594.024000] Uhhuh. NMI received for unknown reason 00 on CPU 0. [17179594.024000] Dazed and confused, but trying to continue [17179594.024000] Do you have a strange power saving mode enabled? [17179597.992000] ipmi: Found new BMC (man_id: 0x000322, prod_id: 0x4311, dev_id: 0x20) [17179598.012000] IPMI Watchdog: Unable to register misc device [17179598.112000] i2c /dev entries driver [17179598.132000] IPMI System Interface driver. [17179598.192000] ipmi_si: Unable to find any System Interface(s) [17179603.892000] Uhhuh. NMI received for unknown reason 00 on CPU 0. [17179603.892000] Dazed and confused, but trying to continue [17179603.892000] Do you have a strange power saving mode enabled? [17179605.724000] Uhhuh. NMI received for unknown reason 00 on CPU 0. [17179605.724000] Dazed and confused, but trying to continue [17179605.724000] Do you have a strange power saving mode enabled? [17179607.872000] Uhhuh. NMI received for unknown reason 00 on CPU 0. <snip and this continues with either a lockup, or a login, then lock up> Nick -- Nick Ellson CCDA, CCNP, CCSP, CCAI, MCSE 2000, Security+, Network+ Network Hobbyist, VFR Private Pilot.