Hi, I have problem to set up an X100P clone card. Installation of zaptel was successful. Also modprobe of zaptel, ztdummy and wcfxo without problems. kernel: wcfxo: module not supported by Novell, setting U taint flag. kernel: ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 16 (level, low) -> IRQ 193 kernel: wcfxo: DAA mode is 'FCC' kernel: Found a Wildcard FXO: Generic Clone kernel: Registered tone zone 0 (United States / North America) But if I do #ztcfg -vvv no channels will be found. the log file reports me: kernel: Registered tone zone 0 (United States / North America) Iam quite sure that zaptel.conf is correct. fxsks=1 loadzone=us defaultzone=us So Iam not sure what happened here, I have found that this clone as used by many others, so it should work. thanks.... best regards Frank
dmesg | grep x100p also im almost positive(correct me if im wrong anyone) you do NOT need ztdummy i repeat, do NOT need ztdummy with x100p then rmmod zaptel && rmmod wctdm && modprobe zaptel && modprobe wctdm or wctfxo or w/e let me know how this works out (post the section for your x100p from zaptel.conf and zapata.conf if you could m8)> >Hi, > >I have problem to set up an X100P clone card. >Installation of zaptel was successful. >Also modprobe of zaptel, ztdummy and wcfxo without problems. > >kernel: wcfxo: module not supported by Novell, setting U taint flag. >kernel: ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 16 (level, low) -> IRQ >193 >kernel: wcfxo: DAA mode is 'FCC' >kernel: Found a Wildcard FXO: Generic Clone >kernel: Registered tone zone 0 (United States / North America) > > >But if I do #ztcfg -vvv no channels will be found. > >the log file reports me: kernel: Registered tone zone 0 (United States / >North >America) > >Iam quite sure that zaptel.conf is correct. >fxsks=1 >loadzone=us >defaultzone=us > >So Iam not sure what happened here, I have found that this clone as used by >many others, so it should work. > >thanks.... > >best regards > >Frank >_______________________________________________ >--Bandwidth and Colocation provided by Easynews.com -- > >asterisk-users mailing list >To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users_________________________________________________________________ Express yourself instantly with MSN Messenger! Download today - it's FREE! http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
On Sat, Jul 22, 2006 at 09:02:48PM +0200, Frank Darner wrote:> Hi, > > I have problem to set up an X100P clone card. > Installation of zaptel was successful. > Also modprobe of zaptel, ztdummy and wcfxo without problems. > > kernel: wcfxo: module not supported by Novell, setting U taint flag. > kernel: ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 16 (level, low) -> IRQ 193 > kernel: wcfxo: DAA mode is 'FCC' > kernel: Found a Wildcard FXO: Generic Clone > kernel: Registered tone zone 0 (United States / North America) > > > But if I do #ztcfg -vvv no channels will be found.What is the exact output from that command? What is the output from 'cat /proc/zaptel/*' -- Tzafrir Cohen sip:tzafrir@local.xorcom.com icq#16849755 iax:tzafrir@local.xorcom.com +972-50-7952406 jabber:tzafrir@jabber.org tzafrir.cohen@xorcom.com http://www.xorcom.com