Hi all, I've been running a generic tor2 card from varion in a box for a couple years now with a few pri's going to it. I thought it was time to pick up another card to experiment with and have on hand as a backup so the boss picked up another varion tormenta2 card but I sure can't seem to get it installed. I started out with the latest debian netboot cd and upgraded to the 2.6 kernel. Everything seems smooth there. I downloaded zaptel-1.2.6, ran make linux26 and installed it, here's the resulting dmesg output on reboot: Zapata Telephony Interface Registered on major 196 Zaptel Version: 1.2.6 Echo Canceller: KB1 ACPI: PCI interrupt 0000:01:08.0[A] -> GSI 20 (level, low) -> IRQ 20 Detected Tormenta 2 Quad T1/PRI or E1/PRA at 0xfcf00800/0xfcf00000 irq 20 Xilinx Chip successfully loaded, configured and started!! Tormenta 2 Quad T1/PRI Card Detected Card number: 2 ztcfg -vvv gets me: Zaptel Configuration ===================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 4: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) Channel map: Channel 01: Clear channel (Default) (Slaves: 01) Channel 02: Clear channel (Default) (Slaves: 02) Channel 03: Clear channel (Default) (Slaves: 03) Channel 04: Clear channel (Default) (Slaves: 04) Channel 05: Clear channel (Default) (Slaves: 05) Channel 06: Clear channel (Default) (Slaves: 06) Channel 07: Clear channel (Default) (Slaves: 07) Channel 08: Clear channel (Default) (Slaves: 08) Channel 09: Clear channel (Default) (Slaves: 09) Channel 10: Clear channel (Default) (Slaves: 10) Channel 11: Clear channel (Default) (Slaves: 11) Channel 12: Clear channel (Default) (Slaves: 12) Channel 13: Clear channel (Default) (Slaves: 13) Channel 14: Clear channel (Default) (Slaves: 14) Channel 15: Clear channel (Default) (Slaves: 15) Channel 16: Clear channel (Default) (Slaves: 16) Channel 17: Clear channel (Default) (Slaves: 17) Channel 18: Clear channel (Default) (Slaves: 18) Channel 19: Clear channel (Default) (Slaves: 19) Channel 20: Clear channel (Default) (Slaves: 20) Channel 21: Clear channel (Default) (Slaves: 21) Channel 22: Clear channel (Default) (Slaves: 22) Channel 23: Clear channel (Default) (Slaves: 23) Channel 24: D-channel (Default) (Slaves: 24) 24 channels configured. ZT_SPANCONFIG failed on span 1: No such device or address (6) /etc/zaptel.conf is the same as my other server: span=1,1,0,esf,b8zs span=2,0,0,esf,b8zs span=3,0,0,esf,b8zs span=4,0,0,esf,b8zs bchan=1-23 dchan=24 loadzone=us defaultzone=us lsmod: tor2 90784 0 zaptel 229636 1 tor2 My functional box is running a much older zaptel (1.0.2) - I seem to recall there being a reason I went with it over the latest when I installed it, but I sure don't remember what it would have been. Anyway here's its dmesg: Zapata Telephony Interface Registered on major 196 Detected Tormenta 2 Quad T1/PRI or E1/PRA at 0xfcf00800/0xfcf00000 irq 16 Xilinx Chip successfully loaded, configured and started!! Tormenta 2 Quad T1/PRI Card Detected Card number: 0 Tor2: Launching card: 0 Registered Tormenta2 PCI Registered tone zone 0 (United States / North America) SPAN 1: Primary Sync Source Zaptel: Master changed to Tor2/0/2 Zaptel: Master changed to Tor2/0/3 Zaptel: Master changed to Tor2/0/4 It seems as if i'm missing the whole "launching card" bit. Any suggestions as to what is actually happening here would be greatly appreciated. I spend most of my time with freebsd so perhaps I've missed an obvious answer. __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com