Alex Barnes
2005-Dec-28 09:48 UTC
[Asterisk-Users] Driver not configuring correctly on TE210P for CCS
Hi all, It sas been a while since I have been on the mailing list but am really hoping someone can help me. Using Dell SC1420, Fedora 4, Asterisk 1.2.1 and a TE210P I cant seem to get the card to configure itself properly for CCS, it always appears as ESF in the /var/log/messages file, although ztcfg reports correctly. No compiles errors that I saw and OS has been updated etc. I am not new to asterisk but this has me stumped (googled and also emailed digium but probably due to the holidays not had a reply.) If I try to run asterisk it complains about not finding the bchannel on 24, note it should be configured to 16 so again I assume its not paying attention to the /etc/zaptel.cong Note: This exact config worked perfectly on asterisk 1.0 and a E100P card. var/log/messages: Dec 28 12:51:55 caudi_apx1 kernel: Zapata Telephony Interface Registered on major 196 Dec 28 12:51:55 caudi_apx1 kernel: ACPI: PCI Interrupt 0000:03:0d.0[A] -> GSI 49 (level, low) -> IRQ 201 Dec 28 12:51:55 caudi_apx1 kernel: Found TE2XXP at base address ddfbff80, remapped to f882ef80 Dec 28 12:51:55 caudi_apx1 kernel: TE2XXP version c01a0164, burst OFF, slip debug: OFF Dec 28 12:51:55 caudi_apx1 kernel: FALC version: 00000005, Board ID: 00 Dec 28 12:51:55 caudi_apx1 kernel: Reg 0: 0x32c0e400 Dec 28 12:51:55 caudi_apx1 kernel: Reg 1: 0x32c0e000 Dec 28 12:51:55 caudi_apx1 kernel: Reg 2: 0xffffffff Dec 28 12:51:55 caudi_apx1 kernel: Reg 3: 0x00000000 Dec 28 12:51:55 caudi_apx1 kernel: Reg 4: 0x00000001 Dec 28 12:51:55 caudi_apx1 kernel: Reg 5: 0x00000000 Dec 28 12:51:55 caudi_apx1 kernel: Reg 6: 0xc01a0164 Dec 28 12:51:55 caudi_apx1 kernel: Reg 7: 0x00001000 Dec 28 12:51:55 caudi_apx1 kernel: Reg 8: 0x00000000 Dec 28 12:51:55 caudi_apx1 kernel: Reg 9: 0x00ff0000 Dec 28 12:51:55 caudi_apx1 kernel: Reg 10: 0x00000000 Dec 28 12:51:55 caudi_apx1 kernel: TE2XXP: Launching card: 0 Dec 28 12:51:55 caudi_apx1 kernel: TE2XXP: Setting up global serial parameters Dec 28 12:51:56 caudi_apx1 kernel: Found a Wildcard: Wildcard TE210P Dec 28 12:51:56 caudi_apx1 kernel: About to enter spanconfig! Dec 28 12:51:56 caudi_apx1 kernel: Done with spanconfig! Dec 28 12:51:56 caudi_apx1 kernel: Registered tone zone 4 (United Kingdom) Dec 28 12:51:56 caudi_apx1 kernel: About to enter startup! Dec 28 12:51:56 caudi_apx1 kernel: TE2XXP: Span 1 configured for ESF/B8ZS Dec 28 12:51:56 caudi_apx1 kernel: wct2xxp: Setting yellow alarm on span 1 Dec 28 12:51:56 caudi_apx1 kernel: SPAN 1: Primary Sync Source Dec 28 12:51:56 caudi_apx1 kernel: 2G: Got interrupt, status = 0000000f, GIS = 0081 Dec 28 12:51:56 caudi_apx1 kernel: 2G: Got interrupt, status = 0000000a, GIS = 0080 Dec 28 12:51:56 caudi_apx1 kernel: 2G: Got interrupt, status = 0000000a, GIS = 0080 Dec 28 12:51:56 caudi_apx1 kernel: VPM: Not Present Dec 28 12:51:56 caudi_apx1 kernel: Completed startup! Dec 28 12:51:56 caudi_apx1 kernel: 2G: Got interrupt, status = 0000000a, GIS = 0080 Dec 28 12:51:56 caudi_apx1 last message repeated 15 times etc/zaptel.conf # Define the E210P span=1,1,0,ccs,hdb3,crc4 bchan=1-8 dchan=16 unused=9-15,17-31 ztcfg: [root@caudi_apx1 ~]# ztcfg -vvv -d 2 Line 154: loadzone=uk Line 162: defaultzone=uk Line 224: span=1,1,0,ccs,hdb3,crc4 Line 225: bchan=1-8 Line 226: dchan=16 Line 227: unused=9-15,17-31 <End of File> Zaptel Configuration ===================== SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) Channel map: Channel 01: Clear channel (Default) (Slaves: 01) Channel 02: Clear channel (Default) (Slaves: 02) Channel 03: Clear channel (Default) (Slaves: 03) Channel 04: Clear channel (Default) (Slaves: 04) Channel 05: Clear channel (Default) (Slaves: 05) Channel 06: Clear channel (Default) (Slaves: 06) Channel 07: Clear channel (Default) (Slaves: 07) Channel 08: Clear channel (Default) (Slaves: 08) Channel 16: D-channel (Default) (Slaves: 16) 9 channels configured. Thanks in advance. Alex PS. If this is in HTML I applogise am having to use the webmail interface of Exchange and cant see if I can change the email type. Information contained in this e-mail and any attachments are intended for the use of the addressee only, and may contain confidential information of Ubiquity Software Corporation. All unauthorized use, disclosure or distribution is strictly prohibited. If you are not the addressee, please notify the sender immediately and destroy all copies of this email. Unless otherwise expressly agreed in writing signed by an officer of Ubiquity Software Corporation, nothing in this communication shall be deemed to be legally binding. Thank you.
Paul Liew
2005-Dec-28 15:45 UTC
[Asterisk-Users] Driver not configuring correctly on TE210P for CCS
Hi Alex, Have you checked that your jumper setting on the card has been shorted for E1. Its open by default to T1 - which overrides your zaptel.conf settings. Cheers, Paul Alex Barnes wrote:> Dec 28 12:51:55 caudi_apx1 kernel: TE2XXP: Launching card: 0 > Dec 28 12:51:55 caudi_apx1 kernel: TE2XXP: Setting up global serial parameters > Dec 28 12:51:56 caudi_apx1 kernel: Found a Wildcard: Wildcard TE210P > Dec 28 12:51:56 caudi_apx1 kernel: About to enter spanconfig! > Dec 28 12:51:56 caudi_apx1 kernel: Done with spanconfig! > Dec 28 12:51:56 caudi_apx1 kernel: Registered tone zone 4 (United Kingdom) > Dec 28 12:51:56 caudi_apx1 kernel: About to enter startup! > Dec 28 12:51:56 caudi_apx1 kernel: TE2XXP: Span 1 configured for ESF/B8ZS > Dec 28 12:51:56 caudi_apx1 kernel: wct2xxp: Setting yellow alarm on span 1 > > etc/zaptel.conf > > # Define the E210P > span=1,1,0,ccs,hdb3,crc4 > bchan=1-8 > dchan=16 > unused=9-15,17-31 > > > > ztcfg: > > [root@caudi_apx1 ~]# ztcfg -vvv -d 2 > Line 154: loadzone=uk > Line 162: defaultzone=uk > Line 224: span=1,1,0,ccs,hdb3,crc4 > Line 225: bchan=1-8 > Line 226: dchan=16 > Line 227: unused=9-15,17-31 > <End of File> >-- www.austechpartnerships.com t) +61 (0)3 9221 0888 SIP) 9999@sip.austechpartnerships.com IAX) 9999@sip.austechpartnerships.com IAXtel) 1700-482-8273 ATP Centrex) 9999