Configuration is the following Rhino channel bank, crossover T1 cable, Asterisk Box TE411p Port 1. I have a cable running from the demarc into a patch panel, then I have a patch panel which runs into the channelbank. Channels 1-5 are the current patched lines. I can call into any of the channels asterisk answers, everything is good. I can login with an IAX client, call between IAX clients, everything is good If I try using a zap channel from an IAX client, dial,zap/1 I get a dial tone, if I manually dial I see in idefisk unknown error 5 on call 0, after a few seconds operator comes on and says "if I want to make a call please hangup try again" If I call in on a zap channel (landline), and then call the same extension above, I get a dial tone and can dial the number manually w/o issues. If I call in on a zap channel (landline), and then have asterisk do the dialing dial,zap/1,9localnumber (i have to dial 9 to get out), it fails, but it works if I dial manually. If I use my channel on my tdm400p to dial it works fine both ways, it's specific to the TE411P. I would think the channel bank is working fine, since I can call into asterisk through it, get a zap channel and then manually dial back out through it. But if Asterisk handles the dialing, through IAX, or building the dial string and then doing it, it fails. Running 1.2.1, opensuse10 (linux 26) te411p (channels 1-5), tdm400p (channel 97). I just added the tdm400p to the system because I cannot use the te411p to make iax -> landline calls. Anyone have a clue or seen this before, I just ran some debugs since I last wrote this, and I see the following in my debugs... << [ TYPE: DTMF (1) SUBCLASS: 9 (57) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: DTMF (1) SUBCLASS: 2 (50) ] [Zap/5-1] Over and over again, eventually i see: << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Null Frame (5) SUBCLASS: N/A (0) ] [Zap/5-1] << [ TYPE: Control (4) SUBCLASS: Answer (4) ] [Zap/5-1] And then the operator tells me to hangup and try again This was when I tried dialing a number from my IAX using: exten => 600,1,Dial(Zap/5/ww99222436) ;I need 9 to dial out on these lines. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20051223/6b9cdfef/attachment.htm