Everyone, I have a TDM400 REV I Ver 1 board and am having an issue with 1 of the 4 FXO channels. FXO 1 always has clicks, pops and echo but the others are crystal clear all of the time. The card is on its own IRQ zztest shows 100% to 99.98% and is getting 1000 int per second. Its not dropping interrupts either. I ran FXOTUNE and it did nothing to fix the issue It only is happening on FXO port 1 Anything else to try? Thanks, -- Tom Vile Baldwin Technology Solutions, Inc Consulting - Web Design - VoIP Telephony www.baldwintechsolutions.com Phone: 518-631-2855 x205 Phone: 978-203-3848 x205 Fax: 518-631-2856
> I have a TDM400 REV I Ver 1 board and am having an issue with 1 of the > 4 FXO channels. FXO 1 always has clicks, pops and echo but the others > are crystal clear all of the time. The card is on its own IRQ zztest > shows 100% to 99.98% and is getting 1000 int per second. Its not > dropping interrupts either. > > I ran FXOTUNE and it did nothing to fix the issue > > It only is happening on FXO port 1 > > Anything else to try?Sure... call digium support. They'll probably rma the module.
I had the same problem - I swapped modules, and the problem stayed with channel 1. I got a replacement from my distributor, but it had the same problem. I ended up getting a board directly from Digium - that solved the problem. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Tom Vile Sent: Tuesday, November 22, 2005 6:31 PM To: Rich Adamson Cc: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] TDM400 FXO port 1 only problem. The problem is not the module though its on the port its plugged into. I can move the module to another port and it works fine, so I was thinking it is the board. I guess I will call Digium and see what they say. thanks On 11/22/05, Rich Adamson <radamson@routers.com> wrote:> > > I have a TDM400 REV I Ver 1 board and am having an issue with 1 of > > the 4 FXO channels. FXO 1 always has clicks, pops and echo but the > > others are crystal clear all of the time. The card is on its own > > IRQ zztest shows 100% to 99.98% and is getting 1000 int per second.> > Its not dropping interrupts either. > > > > I ran FXOTUNE and it did nothing to fix the issue > > > > It only is happening on FXO port 1 > > > > Anything else to try? > > Sure... call digium support. They'll probably rma the module. > > >-- Tom Vile Baldwin Technology Solutions, Inc Consulting - Web Design - VoIP Telephony www.baldwintechsolutions.com Phone: 518-631-2855 x205 Phone: 978-203-3848 x205 Fax: 518-631-2856 _______________________________________________ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Tom Vile wrote:>Everyone, > >I have a TDM400 REV I Ver 1 board and am having an issue with 1 of the >4 FXO channels. FXO 1 always has clicks, pops and echo but the others >are crystal clear all of the time. The card is on its own IRQ zztest >shows 100% to 99.98% and is getting 1000 int per second. Its not >dropping interrupts either. > >I ran FXOTUNE and it did nothing to fix the issue > >It only is happening on FXO port 1 > >Anything else to try? > >Thanks, >-- >Tom Vile > >I had the same problem w/ two boards. Called Digium and they said they had a batch of bad boards go out where port 1 would exhibit the problems you describe. They rma'd the boards for me and all is well. Cheers, Kevin -- Optimacy Communications, LLC http://www.optimacycomm.com