OTR Comm
2005-Oct-31 16:51 UTC
[Asterisk-Users] No D-channels available! CVS-HEAD-10/31/05-16:01
Hello all,
I am having D-channels problems.
I have setup Asterisk (CVS-HEAD-10/31/05-16:01) on RH Fedora Core
4(2.6.13-1.1532_FC4). I also have 2 TE110XP cards set to T1 (only one
with a T1 connect currently). I had my telco provider rebuild the T1 on
a new card, and they say that they can see my D-channels.
Anybody have any ideas about this?
Thanks,
Murrah Boswell
dmesg gives:
...
eth0: Media Link On 100mbps full-duplex
NET: Registered protocol family 10
Disabled Privacy Extensions on device c04756a0(lo)
IPv6 over IPv4 tunneling driver
Zapata Telephony Interface Registered on major 196
Zapata Telephony Interface Unloaded
Zapata Telephony Interface Registered on major 196
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 5 (level, low)
-> IRQ 5
Controller version: 24
FALC version: 00000000
TE110P: Setting up global serial parameters for T1 FALC V1.2
TE110P: Successfully initialized serial bus for card
Found a Wildcard: Digium Wildcard TE110P T1/E1
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level,
low) -> IRQ 10
Controller version: 24
FALC version: 00000000
TE110P: Setting up global serial parameters for T1 FALC V1.2
TE110P: Successfully initialized serial bus for card
Found a Wildcard: Digium Wildcard TE110P T1/E1
Registered tone zone 0 (United States / North America)
TE110P: Span configured for ESF/B8ZS
Calling startup (flags is 4099)
TE110P: Span configured for ESF/B8ZS
Calling startup (flags is 4099)
wcte1xxp: Setting yellow alarm
Zaptel: Master changed to WCT1/1
wcte1xxp: Setting yellow alarm
eth0: no IPv6 routers present
wcte1xxp: Clearing yellow alarm
wcte1xxp: Clearing yellow alarm
Zaptel: Master changed to WCT1/0
my zaptel.conf:
span=1,1,1,esf,b8zs
span=2,0,1,esf,b8zs
bchan=1-23
dchan=24
e&m=25-48
defaultzone=us
loadzone=us
NOTE:span2 doesn't have a T1 connected yet though.
lsmod:
Module Size Used by
wcte11xp 53536 43
zaptel 230660 91 wcte11xp
crc_ccitt 2241 1 zaptel
ipv6 292865 14
sunrpc 197509 1
dm_mod 61917 0
video 16197 0
button 6737 0
battery 9541 0
ac 4933 0
sis900 24385 0
mii 5569 1 sis900
floppy 71861 0
ext3 138569 2
jbd 111065 1 ext3
/proc/zaptel/1:
Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" B8ZS/ESF
1 WCT1/0/1 Clear (In use)
2 WCT1/0/2 Clear (In use)
3 WCT1/0/3 Clear (In use)
4 WCT1/0/4 Clear (In use)
5 WCT1/0/5 Clear (In use)
6 WCT1/0/6 Clear (In use)
7 WCT1/0/7 Clear (In use)
8 WCT1/0/8 Clear (In use)
9 WCT1/0/9 Clear (In use)
10 WCT1/0/10 Clear (In use)
11 WCT1/0/11 Clear (In use)
12 WCT1/0/12 Clear (In use)
13 WCT1/0/13 Clear (In use)
14 WCT1/0/14 Clear (In use)
15 WCT1/0/15 Clear (In use)
16 WCT1/0/16 Clear (In use)
17 WCT1/0/17 Clear (In use)
18 WCT1/0/18 Clear (In use)
19 WCT1/0/19 Clear (In use)
20 WCT1/0/20 Clear (In use)
21 WCT1/0/21 Clear (In use)
22 WCT1/0/22 Clear (In use)
23 WCT1/0/23 Clear (In use)
24 WCT1/0/24 HDLCFCS (In use)
/proc/interrupts:
CPU0
0: 557034 XT-PIC timer
1: 8 XT-PIC i8042
2: 0 XT-PIC cascade
5: 2206093 XT-PIC wcte11xp
8: 1 XT-PIC rtc
9: 0 XT-PIC acpi
10: 2206091 XT-PIC wcte11xp
11: 72141 XT-PIC eth0
12: 93 XT-PIC i8042
14: 3572 XT-PIC ide0
15: 19881 XT-PIC ide1
NMI: 0
ERR: 0