Hi,
i have set up asterisk on debian sarge (kernel 2.2.6.8-2) with chan_capi
and AVM Fritz Card PCI. Asterisk starts up fine, but it does not respond
to any call on the specified MSN.
I have installed the asterisk sample configuration (make sample)
When i enable capi debugging in the asterisk console (capi debug), i get
the following output when a call on MSN 22 comes in:
Thank you very much for some suggestions to resolve that issue. Sorry
for the long post.
====================SNIP======================*CLI> capi debug
CAPI Debugging Enabled
*CLI> capi info
Contr1: 2 B channels total, 2 B channels free.
*CLI> CONNECT_IND ID=001 #0x0018 LEN=0037
Controller/PLCI/NCCI = 0x101
CIPValue = 0x10
CalledPartyNumber = <80>22
CallingPartyNumber = <01 80 2a 2a>10
CalledPartySubaddress = default
CallingPartySubaddress = default
BC = <80 90 a3>
LLC = default
HLC = <91 81>
AdditionalInfo = default
-- CONNECT_IND (PLCI=0x101,DID=22,CID=**10,CIP=0x10,CONTROLLER=0x1)
> ISDN1: msn='22' DNID='22' MSN
== ISDN1: Incoming call '**10' -> '22'
INFO_IND ID=001 #0x0019 LEN=0018
Controller/PLCI/NCCI = 0x101
InfoNumber = 0x70
InfoElement = <80>22
INFO_RESP ID=001 #0x0019 LEN=0012
Controller/PLCI/NCCI = 0x101
-- ISDN1: info element CALLED PARTY NUMBER
> ISDN1: INFO_IND DID digits not used in this state.
INFO_IND ID=001 #0x001a LEN=0016
Controller/PLCI/NCCI = 0x101
InfoNumber = 0x18
InfoElement = <89>
INFO_RESP ID=001 #0x001a LEN=0012
Controller/PLCI/NCCI = 0x101
-- Asterisk Urgent handler
-- ISDN1: info element CHANNEL IDENTIFICATION 89
-- Asterisk Urgent handler
INFO_IND ID=001 #0x001b LEN=0018
Controller/PLCI/NCCI = 0x101
InfoNumber = 0x70
InfoElement = <80>22
INFO_RESP ID=001 #0x001b LEN=0012
Controller/PLCI/NCCI = 0x101
-- ISDN1: info element CALLED PARTY NUMBER
> ISDN1: INFO_IND DID digits not used in this state.
INFO_IND ID=001 #0x001c LEN=0016
Controller/PLCI/NCCI = 0x101
InfoNumber = 0x18
InfoElement = <89>
INFO_RESP ID=001 #0x001c LEN=0012
Controller/PLCI/NCCI = 0x101
-- ISDN1: info element CHANNEL IDENTIFICATION 89
-- Asterisk Urgent handler
DISCONNECT_IND ID=001 #0x001d LEN=0014
Controller/PLCI/NCCI = 0x101
Reason = 0x0
DISCONNECT_RESP ID=001 #0x001d LEN=0012
Controller/PLCI/NCCI = 0x101
== ISDN1: CAPI Hangingup
== ISDN1: Interface cleanup PLCI=0x101
-- Asterisk Urgent handler
====================SNIP======================
Here are some configuration details of my setup:
modules.conf:
============
[modules]
autoload=yes
noload => pbx_gtkconsole.so
;load => pbx_gtkconsole.so
noload => pbx_kdeconsole.so
noload => app_intercom.so
noload => chan_modem.so
noload => chan_modem_aopen.so
noload => chan_modem_bestdata.so
noload => chan_modem_i4l.so
load => res_musiconhold.so
noload => chan_alsa.so
;noload => chan_oss.so
load => chan_capi.so
load => res_features.so
[global]
;chan_modem.so=yes
chan_capi.so=yes
capi.conf:
=========
[general]
nationalprefix=0
internationalprefix=00
rxgain=0.8
txgain=0.8
;ulaw=yes ;set this, if you live in u-law world instead of a-law
[ISDN1] ;this example interface gets name 'ISDN1' and may be
any
;name not starting with 'g' or 'contr'.
;ntmode=yes ;if isdn card operates in nt mode, set this to yes
isdnmode=msn ;'MSN' (point-to-multipoint) or 'DID' (direct
inward
dial)
;when using NT-mode, ptp should be set in any case
incomingmsn=22 ;allow incoming calls to this list of MSNs/DIDs, * =any
msn=22
;controller=0 ;ISDN4BSD default
;controller=7 ;ISDN4BSD USB default
controller=1 ;capi controller number to use
group=1 ;dialout group
;prefix=0 ;set a prefix to calling number on incoming calls
softdtmf=on ;enable/disable software dtmf detection, recommended
for AVM ca
rds
relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf
detection
accountcode= ;Asterisk accountcode to use in CDRs
context=demo ;context for incoming calls
holdtype=hold ;when Asterisk puts the call on hold, ISDN HOLD will be
used. If
;set to 'local' (default value), no hold is done and
Asterisk may
;play MOH.
immediate=yes ;immediate start of pbx with extension 's' if no digits
were
;received on incoming call (no destination number yet)
;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression
;echocancel=yes ;EICON DIVA SERVER (CAPI) echo cancelation
;(possible values: 'no', 'yes',
'force', 'g164',
'g165')
echocancelold=yes;use facility selector 6 instead of correct 8
(necessary for ol
der eicon drivers)
;echotail=64 ;echo cancel tail setting
;bridge=yes ;native bridging (CAPI line interconnect) if available
;callgroup=1 ;Asterisk call group
;deflect=1234567 ;deflect incoming calls to 1234567 if all B channels
are busy
devices=2 ;number of concurrent calls on this controller
;(2 makes sense for single BRI, 30 for PRI)
Best regards
Sebastian Voss
Informatecs Systems