Good day all This is a error that keeps on popping up in my /var/log/messages when I get incoming or outgoing calls on my bri card connected to 4 telco isdn units?It is a junghanns 4 port card with the latest version of the drivers and latest asterisk Apr 29 11:37:39 ccv kernel: qozap: BAD CRC for hdlc frame on card 1 (cardID 0) S/T port 1 Apr 29 11:37:39 ccv kernel: qozap: check the 100 Ohm termination for this span! Apr 29 11:45:25 ccv kernel: zaptel Disabled echo canceller because of tone (rx) on channel 1 Please help and advice?
Did you put your card in TE mode ? To it seems you have configured your card to act like a NT but if you are connected to bri telco lines, it should be in TE mode check in your zaptel.conf : bri te signalling regards David -----Message d'origine----- De : Altus Snyman [mailto:altus@stormcorp.co.za] Envoy? : vendredi 29 avril 2005 12:08 ? : Asterisk Users Mailing List - Non-Commercial Discussion Objet : [Asterisk-Users] bri error Good day all This is a error that keeps on popping up in my /var/log/messages when I get incoming or outgoing calls on my bri card connected to 4 telco isdn units?It is a junghanns 4 port card with the latest version of the drivers and latest asterisk Apr 29 11:37:39 ccv kernel: qozap: BAD CRC for hdlc frame on card 1 (cardID 0) S/T port 1 Apr 29 11:37:39 ccv kernel: qozap: check the 100 Ohm termination for this span! Apr 29 11:45:25 ccv kernel: zaptel Disabled echo canceller because of tone (rx) on channel 1 Please help and advice? _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
The problem may then originate from the NT of your telco .... -----Message d'origine----- De : Altus Snyman [mailto:altus@stormcorp.co.za] Envoy? : vendredi 29 avril 2005 12:21 ? : David Masure Cc : Asterisk Users Mailing List - Non-Commercial Discussion Objet : RE: [Asterisk-Users] bri error if I do a zttool it shows TE mode On Fri, 2005-04-29 at 12:14, David Masure wrote:> Did you put your card in TE mode ? > > To it seems you have configured your card to act like a NT but if you > are connected to bri telco lines, it should be in TE mode > > check in your zaptel.conf : bri te signalling > > regards > > David > > > > -----Message d'origine----- > De : Altus Snyman [mailto:altus@stormcorp.co.za] > Envoy? : vendredi 29 avril 2005 12:08 > ? : Asterisk Users Mailing List - Non-Commercial Discussion > Objet : [Asterisk-Users] bri error > > > Good day all > This is a error that keeps on popping up in my /var/log/messages whenI> get incoming or outgoing calls on my bri card connected to 4 telcoisdn> units?It is a junghanns 4 port card with the latest version of the > drivers and latest asterisk > Apr 29 11:37:39 ccv kernel: qozap: BAD CRC for hdlc frame on card 1 > (cardID 0) S/T port 1 > Apr 29 11:37:39 ccv kernel: qozap: check the 100 Ohm termination for > this span! > Apr 29 11:45:25 ccv kernel: zaptel Disabled echo canceller because of > tone (rx) on channel 1 > > Please help and advice? > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
Hi All
When I phone in I get a dead line and this message, can anyone help here?
I am using a Junghanns 4 port with two ISDN BRI.
Accepting voice call from '0118071141' to '5161' on channel
0/2, span 1
May 5 08:13:59 WARNING[3839]: chan_zap.c:7514 zt_pri_error: PRI: received
SETUP message for call that is not a new call, wicked!!! going on ...
May 5 08:13:59 WARNING[3839]: chan_zap.c:8019 pri_dchannel: Ring requested
on channel 0/1 already in use on span 1. Hanging up owner.
-- Executing Answer("Zap/2-1", "") in new stack
May 5 08:14:02 WARNING[3839]: chan_zap.c:7514 zt_pri_error: PRI: !! No
channel map, no channel, and no ds1? What am I supposed to identify?
May 5 08:14:02 WARNING[3839]: chan_zap.c:7514 zt_pri_error: PRI: !! Unable
to add IE 'Channel Identification'
== Spawn extension (bi_ct, 5161, 2) exited non-zero on 'Zap/2-1'
-- Hungup 'Zap/2-1'
May 5 08:14:02 WARNING[3839]: chan_zap.c:7514 zt_pri_error: PRI: !! Got
reject for frame 3, retransmitting frame 3 now, updating n_r!
May 5 08:14:04 WARNING[3839]: chan_zap.c:7514 zt_pri_error: PRI: !! Got
reject for frame 4, but we have nothing -- resetting!