I am trying to get the drivers working with this device with 4 fxo modules on it. I do a modprobe zaptel and no errors appear. But when I do modprobe wctdm the following errors appear: Notice: Configuration file is /etc/zaptel.conf line 4: Cannot get number of tones chanel 1 line 4: Cannot init tones chanel 1 line 4: Cannot get number of tones chanel 2 line 4: Cannot init tones chanel 2 line 4: Cannot get number of tones chanel 3 line 4: Cannot init tones chanel 3 line 4: Cannot get number of tones chanel 4 line 4: Cannot init tones chanel 4 8 error(s) detected /lib/modules/2.4.22-2f/misc/wctdm.o: post-install wctdm failed /lib/modules/2.4.22-2f/misc/wctdm.o: insmod wctdm failed I have googled the mailing lists and have not been able to find anything on these errors. My config of zaptel.conf fxsks=1-4 loadzone=au defaultzone=au channels=1-4 zapata.conf [channels] language=en ; XTDM20B Port #1,2 plugged into PSTN ; context=from-1800 signalling=fxs_ks faxdetect=incoming usecallerid=yes echocancel=yes echocancelwhenbridged=no group=1 channel=1 context=from-pstn signalling=fxs_ks faxdetect=incoming usecallerid=yes echocancel=yes echocancelwhenbridged=no echotraining=800 group=3 channel=2-3 context=from-fax signalling=fxs_ks faxdetect=incoming usecallerid=yes echocancel=yes echocancelwhenbridged=no echotraining=800 group=3 channel=4 Has anyone seen this problem before? Does anyone know a cure? Any help is greatly appreciated. Regards, Greg
Inline...> I am trying to get the drivers working with this device with 4 fxo > modules on it. I do a modprobe zaptel and no errors appear. But when I > do modprobe wctdm the following errors appear: > > Notice: Configuration file is /etc/zaptel.conf > line 4: Cannot get number of tones chanel 1 > line 4: Cannot init tones chanel 1 > line 4: Cannot get number of tones chanel 2 > line 4: Cannot init tones chanel 2 > line 4: Cannot get number of tones chanel 3 > line 4: Cannot init tones chanel 3 > line 4: Cannot get number of tones chanel 4 > line 4: Cannot init tones chanel 4 > > 8 error(s) detected > > /lib/modules/2.4.22-2f/misc/wctdm.o: post-install wctdm failed > /lib/modules/2.4.22-2f/misc/wctdm.o: insmod wctdm failed > > > I have googled the mailing lists and have not been able to find > anything on these errors. > > My config of zaptel.conf > > fxsks=1-4 > loadzone=au > defaultzone=au > channels=1-4Unless the above is a typo, "channels=1-4" should not be in this file; only the first three lines> zapata.conf > > [channels] > language=en > > ; XTDM20B Port #1,2 plugged into PSTN > ; > context=from-1800 > signalling=fxs_ks > faxdetect=incoming > usecallerid=yes > echocancel=yes > echocancelwhenbridged=no > group=1 > channel=1Not sure about the syntax of "channel=1"; I know channel=>1 works though.> context=from-pstn > signalling=fxs_ks > faxdetect=incoming > usecallerid=yes > echocancel=yes > echocancelwhenbridged=no > echotraining=800 > group=3 > channel=2-3 > > context=from-fax > signalling=fxs_ks > faxdetect=incoming > usecallerid=yes > echocancel=yes > echocancelwhenbridged=no > echotraining=800 > group=3 > channel=4
Thankyou. That did the trick. I must have got confused with zaptel and zapata conf files with an example. Regards, Greg On 18/03/2005, at 10:38 PM, Rich Adamson wrote:> Inline... > >> I am trying to get the drivers working with this device with 4 fxo >> modules on it. I do a modprobe zaptel and no errors appear. But when I >> do modprobe wctdm the following errors appear: >> >> Notice: Configuration file is /etc/zaptel.conf >> line 4: Cannot get number of tones chanel 1 >> line 4: Cannot init tones chanel 1 >> line 4: Cannot get number of tones chanel 2 >> line 4: Cannot init tones chanel 2 >> line 4: Cannot get number of tones chanel 3 >> line 4: Cannot init tones chanel 3 >> line 4: Cannot get number of tones chanel 4 >> line 4: Cannot init tones chanel 4 >> >> 8 error(s) detected >> >> /lib/modules/2.4.22-2f/misc/wctdm.o: post-install wctdm failed >> /lib/modules/2.4.22-2f/misc/wctdm.o: insmod wctdm failed >> >> >> I have googled the mailing lists and have not been able to find >> anything on these errors. >> >> My config of zaptel.conf >> >> fxsks=1-4 >> loadzone=au >> defaultzone=au >> channels=1-4 > > Unless the above is a typo, "channels=1-4" should not be in this file; > only the first three lines > >> zapata.conf >> >> [channels] >> language=en >> >> ; XTDM20B Port #1,2 plugged into PSTN >> ; >> context=from-1800 >> signalling=fxs_ks >> faxdetect=incoming >> usecallerid=yes >> echocancel=yes >> echocancelwhenbridged=no >> group=1 >> channel=1 > > Not sure about the syntax of "channel=1"; I know channel=>1 works > though. > >> context=from-pstn >> signalling=fxs_ks >> faxdetect=incoming >> usecallerid=yes >> echocancel=yes >> echocancelwhenbridged=no >> echotraining=800 >> group=3 >> channel=2-3 >> >> context=from-fax >> signalling=fxs_ks >> faxdetect=incoming >> usecallerid=yes >> echocancel=yes >> echocancelwhenbridged=no >> echotraining=800 >> group=3 >> channel=4 > > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >