Michael Løjtnant
2004-Nov-23 08:52 UTC
[Asterisk-Users] Fax over TDM400 and E100P disconnects
Hi all,
I am having some problems getting my fax-machines to work properly. I can make
them dialup, and they cal also recive calls, but very often they disconnect
during the data-transfer. Anyone got some ideas?
The setup is like this:
Pri <-> E100P <-> Asterisk <-> TDM400 <-> Fax-Machine
I have 1xE100P, and 2xTDM400
There is no errors writte in the Console, nor in the sys.log
System:
SuperMicro with P4 2.53GHz
512 MB Ram
3Ware IDE Raid Cont. (Running Raid 5)
1 x E100P
2 x TDM400
1 x Fritz! ISDN Card
Kernel-2.6.8.1 (Running ACPI, and Preemptible)
Asterisk, Libpri and zaptel is from stable 1.0.2 release
zaptel.conf
span=1,1,0,ccs,hdb3,crc4
bchan=1-15,17-31
dchan=16
fxoks=32,33,36-39
fxsks=34,35
zapata.conf
group=4
context=faxing
faxdetect=no
echocancel=no
echocancelwhenbridged=no
echotraining=no
signalling=fxo_ks
language=dk
channel => 36
extension.conf (for incomming calls)
exten => 39550707,1,Dial(Zap/g4)
exten => 39550707,2,Hangup
exten => 39550707,102,Hangup
extension.conf (for out-going calls)
[faxing]
exten => _.,1,Dial(${ISDN_PRI}/${EXTEN},30,r)
exten => _.,2,noop(${HANGUPCAUSE})
exten => _.,3,Hangup
exten => _.,102,noop(${HANGUPCAUSE})
exten => _.,103,Hangup
[root@pbx root# cat /proc/interrupts
CPU0
0: 84470982 IO-APIC-edge timer
1: 13 IO-APIC-edge i8042
9: 0 IO-APIC-level acpi
12: 59 IO-APIC-edge i8042
14: 13 IO-APIC-edge ide0
17: 469492 IO-APIC-level 3ware Storage Controller
18: 84428437 IO-APIC-level t1xxp
19: 84436740 IO-APIC-level wctdm
20: 84443418 IO-APIC-level wctdm
21: 2 IO-APIC-level fcpcipnp
22: 5311480 IO-APIC-level eth0
23: 1030767 IO-APIC-level eth1
NMI: 0
LOC: 84477235
ERR: 0
MIS: 0
And from Dmesg:
Zapata Telephony Interface Registered on major 196
ACPI: PCI interrupt 0000:01:01.0[A] -> GSI 18 (level, low) -> IRQ 18
Framer: DS21554, Revision: 5 (E1)
Found a Wildcard: Digium Wildcard E100P E1/PRA
ACPI: PCI interrupt 0000:01:02.0[A] -> GSI 19 (level, low) -> IRQ 19
Freshmaker version: 63
Freshmaker passed register test
Module 0: Installed -- AUTO FXS/DPO
Module 1: Installed -- AUTO FXS/DPO
Module 2: Installed -- AUTO FXO (FCC mode)
Module 3: Installed -- AUTO FXO (FCC mode)
Found a Wildcard TDM: Wildcard TDM400P REV E/F (4 modules)
ACPI: PCI interrupt 0000:01:03.0[A] -> GSI 20 (level, low) -> IRQ 20
Freshmaker version: 71
Freshmaker passed register test
Module 0: Installed -- AUTO FXS/DPO
Module 1: Installed -- AUTO FXS/DPO
Module 2: Installed -- AUTO FXS/DPO
Module 3: Installed -- AUTO FXS/DPO
Found a Wildcard TDM: Wildcard TDM400P REV E/F (4 modules)
Registered tone zone 3 (Netherlands)
Using CCS/HDB3 coding/framing with CRC4 120 Ohms
Calling startup (flags is 4099)
--
Med venlig hilsen / Best regards
Michael L?jtnant - Systems Engineer
ZyXEL Communications A/S
Columbusvej 5 - 2860 S?borg
Tel (+45) 3955 0700 - Fax (+45) 3955 0707