Hello, I want to connect an adit 600 to a T400P. I have been told a crossover cable is needed. Is this the same crossover cable as ethernet? If no, could anyone post a crossover T1 pinout? Regards, Iv?n -- Iv?n Aponte email: iaponte@lemuria-asesores.com Office: +58(212)9524620 Mobile: +58(414)2774713
A straight thru are pins 1,2,4,5. To make a x-over terminate on end using 1,2,4,5 and the other end crossing pins 1 to 5 and 2 to 4. Mike Michael Kane To-Talk Communications LLC. 37 Sandusky Dr. Wareham, Ma. 02571 www.to-talk.com 508-295-2826 ----- Original Message ----- From: "Iv?n Aponte" <iaponte@lemuria-asesores.com> To: <asterisk-users@lists.digium.com> Sent: Friday, July 04, 2003 9:09 AM Subject: [Asterisk-Users] Crossover T1 cable> Hello, > > I want to connect an adit 600 to a T400P. I have been told a crossover > cable is needed. Is this the same crossover cable as ethernet? If no, > could anyone post a crossover T1 pinout? > > Regards, > > Iv?n > > -- > Iv?n Aponte > email: iaponte@lemuria-asesores.com > Office: +58(212)9524620 > Mobile: +58(414)2774713 > > > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users >
frank.barthe@prescom.net
2003-Jul-04 07:17 UTC
[Asterisk-Users] PCI Master abort (debian / S400P & X101P
Debian / kernel 2.4.18.
Found in /proc/pci ::
Bus 0, device 0, function 0: Host bridge: Intel Corp. 430HX -
82439HX TXC [Triton II] (rev 3).
Bus 0, device 7, function 0: ISA bridge: Intel Corp. 82371SB PIIX3
ISA [Natoma/Triton II] (rev 1).
Bus 0, device 7, function 1: IDE interface: Intel Corp. 82371SB
PIIX3 IDE [Natoma/Triton II] (rev 0).
Bus 0, device 9, function 0: VGA compatible controller: IRQ 10.
Bus 0, device 10, function 0: Tiger Jet Network Inc. Model 300 128k
(rev 0). IRQ 12.
Bus 0, device 12, function 0: Tiger Jet Network Inc. Model 300 128k
(#2) (rev 0). IRQ 9.
Bus 0, device 11, function 0: Realtek Semiconductor Co., Ltd.
RTL-8029(AS) (rev 0). IRQ 11.
Commands sent :
=> modprobe zaptel
=> modprob wcfxs
=> modprobe wcfxo
No pb !
THEN :
wait about 2 minutes (no more command passed)
=> PCI Master abort
OR
=> asterisk -cvvv
=> (zt_open): Unable to specify channel 1
=> PCI Master abort
_______________________________________________________________________________
Does any body work with the same HW configuration (1 FXO + 1 FXS) ?
(Wildcard S400P 4 modules / 1 installed + Wildcard X101P)
http://lists.digium.com/pipermail/asterisk-users/2002-November/005795.html PS. book mark this in the future, the archives are you friend http://www.google.com/custom?domains=www.marko.net&sitesearch=lists.digium.c om -----Original Message----- From: Iv?n Aponte <iaponte@lemuria-asesores.com> To: asterisk-users@lists.digium.com <asterisk-users@lists.digium.com> Date: July 4, 2003 6:18 AM Subject: [Asterisk-Users] Crossover T1 cable Hello, I want to connect an adit 600 to a T400P. I have been told a crossover cable is needed. Is this the same crossover cable as ethernet? If no, could anyone post a crossover T1 pinout? Regards, Iv?n -- Iv?n Aponte email: iaponte@lemuria-asesores.com Office: +58(212)9524620 Mobile: +58(414)2774713 _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users
Martin Pycko
2003-Jul-04 11:41 UTC
[Asterisk-Users] PCI Master abort (debian / S400P & X101P
You have one board on the same IRQ as VGA. Try to replace the board in a diffrent PCI slot or maybe you can do the IRQ job in the BIOS. Martin On Fri, 4 Jul 2003 frank.barthe@prescom.net wrote:> Debian / kernel 2.4.18. > Found in /proc/pci :: > Bus 0, device 0, function 0: Host bridge: Intel Corp. 430HX - > 82439HX TXC [Triton II] (rev 3). > Bus 0, device 7, function 0: ISA bridge: Intel Corp. 82371SB PIIX3 > ISA [Natoma/Triton II] (rev 1). > Bus 0, device 7, function 1: IDE interface: Intel Corp. 82371SB > PIIX3 IDE [Natoma/Triton II] (rev 0). > Bus 0, device 9, function 0: VGA compatible controller: IRQ 10. > Bus 0, device 10, function 0: Tiger Jet Network Inc. Model 300 128k > (rev 0). IRQ 12. > Bus 0, device 12, function 0: Tiger Jet Network Inc. Model 300 128k > (#2) (rev 0). IRQ 9. > Bus 0, device 11, function 0: Realtek Semiconductor Co., Ltd. > RTL-8029(AS) (rev 0). IRQ 11. > > Commands sent : > => modprobe zaptel > => modprob wcfxs > => modprobe wcfxo > > No pb ! > > THEN : > > wait about 2 minutes (no more command passed) > => PCI Master abort > > OR > > => asterisk -cvvv > => (zt_open): Unable to specify channel 1 > => PCI Master abort > _______________________________________________________________________________ > > Does any body work with the same HW configuration (1 FXO + 1 FXS) ? > (Wildcard S400P 4 modules / 1 installed + Wildcard X101P) > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users >