thr3ads.net - Xen devel - [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version [Nov 2008]

If this information is useful, please help other people find it:
Share via:

Manyam, Ramesh

2008-Nov-27 08:36 UTC

[Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

A gentle reminder on this issue

Please can any one help on this problem?

________________________________
From: Manyam, Ramesh
Sent: Wednesday, November 19, 2008 7:46 PM
To: xen-devel@lists.xensource.com
Subject: megaraid sas driver failing in Xen-3.4 unstable version

On Xen-3.4 (unstable version), I have created CentOS HVM guest & WS2K8 HVM
guest and dedicated MegaRAID SAS controller but I am not able to see the disk
which is connected to MegaRAID SAS controller when I do fdisk -l (vtd support is
enabled in Xen).

Looks like the pci device(MegaRAID SAS controller) is getting dedicated
successfully as I can see the device in the list of pci devices shown by
lspci(on CentOS HVM).

00:06.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS

However the driver is not getting attached properly and fails with the following
error

======================================================================================"dmesg"
of HVM CentOS
megasas: Failed to init firmware
ACPI: PCI interrupt for device 0000:00:06.0 disabled

"/var/log/messages"
pciback 0000:02:0e.0: seizing device
 PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
 ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
 ACPI: PCI interrupt for device 0000:02:0e.0 disabled
======================================================================================

On WS2K8 HVM, I am able to see MegaRAID SAS controller under "Storage
Controllers" on WS2K8 HVM and the status of device is

========================================================================================================================================================This
device cannot start.(Code 10)
Description:
 Windows was able to successfully install device driver software, but the driver
software encountered a problem when it tried to run. The problem code is
 10.
Problem Signature:
 Problem Event Name:PnPDeviceProblemCode
 Architecture: x86
 Hardware Id: PCI\VEN_1000&DEV_0411&SUBSYS_10081000&REV_00
 Setup class GUID: {4d36e97b-e325-11ce-bfc1-08002be10318}
 PnP problem code: 0000000A
 Driver name: megasas.sys
 Driver version: 2.13.0.32
 Driver date: 01-19-2008
 OS Version: 6.0.6001.2.1.0.272.7
 Locale ID: 1033
 =======================================================================================================================================================And
also I am not able to see the disk which is connected to MegaRAID SAS controller

==========================================================================="/var/log/messages"
pciback 0000:02:0e.0: seizing device
PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
ACPI: PCI interrupt for device 0000:02:0e.0 disabled
===========================================================================

Any clues ?

Thanks,
Ramesh

_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Han, Weidong

2008-Nov-27 08:47 UTC

head link

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

you mean you assign MegaRAID SAS controller with VT-d to your guest?

You'd better provide more info, such as serial output, so people can be easy
to help you.

Regards,
Weidong

________________________________
From: xen-devel-bounces@lists.xensource.com
[mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Manyam, Ramesh
Sent: 2008年11月27日 16:36
To: xen-devel@lists.xensource.com
Subject: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

A gentle reminder on this issue

Please can any one help on this problem?

________________________________
From: Manyam, Ramesh
Sent: Wednesday, November 19, 2008 7:46 PM
To: xen-devel@lists.xensource.com
Subject: megaraid sas driver failing in Xen-3.4 unstable version


On Xen-3.4 (unstable version), I have created CentOS HVM guest & WS2K8 HVM
guest and dedicated MegaRAID SAS controller but I am not able to see the disk
which is connected to MegaRAID SAS controller when I do fdisk –l (vtd support is
enabled in Xen).

Looks like the pci device(MegaRAID SAS controller) is getting dedicated
successfully as I can see the device in the list of pci devices shown by
lspci(on CentOS HVM).

00:06.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS


However the driver is not getting attached properly and fails with the following
error

======================================================================================“dmesg”
of HVM CentOS
megasas: Failed to init firmware
ACPI: PCI interrupt for device 0000:00:06.0 disabled


“/var/log/messages”
pciback 0000:02:0e.0: seizing device
 PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
 ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
 ACPI: PCI interrupt for device 0000:02:0e.0 disabled
======================================================================================


On WS2K8 HVM, I am able to see MegaRAID SAS controller under “Storage
Controllers” on WS2K8 HVM and the status of device is

========================================================================================================================================================This
device cannot start.(Code 10)
Description:
 Windows was able to successfully install device driver software, but the driver
software encountered a problem when it tried to run. The problem code is
 10.
Problem Signature:
 Problem Event Name:PnPDeviceProblemCode
 Architecture: x86
 Hardware Id: PCI\VEN_1000&DEV_0411&SUBSYS_10081000&REV_00
 Setup class GUID: {4d36e97b-e325-11ce-bfc1-08002be10318}
 PnP problem code: 0000000A
 Driver name: megasas.sys
 Driver version: 2.13.0.32
 Driver date: 01-19-2008
 OS Version: 6.0.6001.2.1.0.272.7
 Locale ID: 1033
 =======================================================================================================================================================And
also I am not able to see the disk which is connected to MegaRAID SAS controller

===========================================================================“/var/log/messages”
pciback 0000:02:0e.0: seizing device
PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
ACPI: PCI interrupt for device 0000:02:0e.0 disabled
===========================================================================

Any clues ?

Thanks,
Ramesh


_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Ian Pratt

2008-Nov-27 08:49 UTC

head link

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstableversion

> On Xen-3.4 (unstable version), I have created CentOS HVM guest & WS2K8
> HVM guest and dedicated MegaRAID SAS controller but I am not able to
> see the disk which is connected to MegaRAID SAS controller when I do
> fdisk -l (vtd support is enabled in Xen).
>
> "dmesg" of HVM CentOS
> 
> megasas: Failed to init firmware
Some devices have drivers/firmware that are not ''virtualization
friendly''. For example, they may require that the guest-visible BARs
match the real machine BARs. A common cause of this is drivers that read
the configured BARs via the device exporting them by a private MMIO
interface rather than from the PCI config space, thus they can''t be
re-virtualized by Xen and hence the driver sees incorrect values. 

Adding debug code to the linux driver is probably the best way to
proceed, or try contacting the LSI driver author.

Ian 



_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Manyam, Ramesh

2008-Nov-27 08:56 UTC

head link

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

VT-d support is enabled

Here I am attaching three files dmesg (hvm dmesgs), dom0_varlogmessages and
xmdmesg

Thanks,
Ramesh
________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 2:18 PM
To: Manyam, Ramesh; ''xen-devel@lists.xensource.com''
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

you mean you assign MegaRAID SAS controller with VT-d to your guest?

You''d better provide more info, such as serial output, so people can be
easy to help you.

Regards,
Weidong

________________________________
From: xen-devel-bounces@lists.xensource.com
[mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Manyam, Ramesh
Sent: 2008年11月27日 16:36
To: xen-devel@lists.xensource.com
Subject: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version
A gentle reminder on this issue

Please can any one help on this problem?

________________________________
From: Manyam, Ramesh
Sent: Wednesday, November 19, 2008 7:46 PM
To: xen-devel@lists.xensource.com
Subject: megaraid sas driver failing in Xen-3.4 unstable version


On Xen-3.4 (unstable version), I have created CentOS HVM guest & WS2K8 HVM
guest and dedicated MegaRAID SAS controller but I am not able to see the disk
which is connected to MegaRAID SAS controller when I do fdisk -l (vtd support is
enabled in Xen).

Looks like the pci device(MegaRAID SAS controller) is getting dedicated
successfully as I can see the device in the list of pci devices shown by
lspci(on CentOS HVM).

00:06.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS


However the driver is not getting attached properly and fails with the following
error

======================================================================================“dmesg”
of HVM CentOS
megasas: Failed to init firmware
ACPI: PCI interrupt for device 0000:00:06.0 disabled


“/var/log/messages”
pciback 0000:02:0e.0: seizing device
 PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
 ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
 ACPI: PCI interrupt for device 0000:02:0e.0 disabled
======================================================================================


On WS2K8 HVM, I am able to see MegaRAID SAS controller under “Storage
Controllers” on WS2K8 HVM and the status of device is

========================================================================================================================================================This
device cannot start.(Code 10)
Description:
 Windows was able to successfully install device driver software, but the driver
software encountered a problem when it tried to run. The problem code is
 10.
Problem Signature:
 Problem Event Name:PnPDeviceProblemCode
 Architecture: x86
 Hardware Id: PCI\VEN_1000&DEV_0411&SUBSYS_10081000&REV_00
 Setup class GUID: {4d36e97b-e325-11ce-bfc1-08002be10318}
 PnP problem code: 0000000A
 Driver name: megasas.sys
 Driver version: 2.13.0.32
 Driver date: 01-19-2008
 OS Version: 6.0.6001.2.1.0.272.7
 Locale ID: 1033
 =======================================================================================================================================================And
also I am not able to see the disk which is connected to MegaRAID SAS controller

===========================================================================“/var/log/messages”
pciback 0000:02:0e.0: seizing device
PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
ACPI: PCI interrupt for device 0000:02:0e.0 disabled
===========================================================================

Any clues ?

Thanks,
Ramesh





_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Han, Weidong

2008-Nov-27 09:13 UTC

head link

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

Did you use VT-d followed docs/misc/vtd.txt?

Per xmdmesg file, device 02:09.0 didn't be mapped in context sucessfully. Is
device 02:09.0 the MegaRAID SAS controller? Can you post "lspci -v"
output?



________________________________
From: Manyam, Ramesh [mailto:Ramesh.Manyam@lsi.com]
Sent: 2008年11月27日 16:57
To: Han, Weidong
Cc: xen-devel@lists.xensource.com
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

VT-d support is enabled

Here I am attaching three files dmesg (hvm dmesgs), dom0_varlogmessages and
xmdmesg

Thanks,
Ramesh
________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 2:18 PM
To: Manyam, Ramesh; 'xen-devel@lists.xensource.com'
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

you mean you assign MegaRAID SAS controller with VT-d to your guest?

You'd better provide more info, such as serial output, so people can be easy
to help you.

Regards,
Weidong

________________________________
From: xen-devel-bounces@lists.xensource.com
[mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Manyam, Ramesh
Sent: 2008年11月27日 16:36
To: xen-devel@lists.xensource.com
Subject: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version
A gentle reminder on this issue

Please can any one help on this problem?

________________________________
From: Manyam, Ramesh
Sent: Wednesday, November 19, 2008 7:46 PM
To: xen-devel@lists.xensource.com
Subject: megaraid sas driver failing in Xen-3.4 unstable version


On Xen-3.4 (unstable version), I have created CentOS HVM guest & WS2K8 HVM
guest and dedicated MegaRAID SAS controller but I am not able to see the disk
which is connected to MegaRAID SAS controller when I do fdisk –l (vtd support is
enabled in Xen).

Looks like the pci device(MegaRAID SAS controller) is getting dedicated
successfully as I can see the device in the list of pci devices shown by
lspci(on CentOS HVM).

00:06.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS


However the driver is not getting attached properly and fails with the following
error

======================================================================================“dmesg”
of HVM CentOS
megasas: Failed to init firmware
ACPI: PCI interrupt for device 0000:00:06.0 disabled


“/var/log/messages”
pciback 0000:02:0e.0: seizing device
 PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
 ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
 ACPI: PCI interrupt for device 0000:02:0e.0 disabled
======================================================================================


On WS2K8 HVM, I am able to see MegaRAID SAS controller under “Storage
Controllers” on WS2K8 HVM and the status of device is

========================================================================================================================================================This
device cannot start.(Code 10)
Description:
 Windows was able to successfully install device driver software, but the driver
software encountered a problem when it tried to run. The problem code is
 10.
Problem Signature:
 Problem Event Name:PnPDeviceProblemCode
 Architecture: x86
 Hardware Id: PCI\VEN_1000&DEV_0411&SUBSYS_10081000&REV_00
 Setup class GUID: {4d36e97b-e325-11ce-bfc1-08002be10318}
 PnP problem code: 0000000A
 Driver name: megasas.sys
 Driver version: 2.13.0.32
 Driver date: 01-19-2008
 OS Version: 6.0.6001.2.1.0.272.7
 Locale ID: 1033
 =======================================================================================================================================================And
also I am not able to see the disk which is connected to MegaRAID SAS controller

===========================================================================“/var/log/messages”
pciback 0000:02:0e.0: seizing device
PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
ACPI: PCI interrupt for device 0000:02:0e.0 disabled
===========================================================================

Any clues ?

Thanks,
Ramesh


_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Han, Weidong

2008-Nov-27 14:28 UTC

head link

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

what's 02:09.0? why is it not showed in lspci -v?

________________________________
From: Manyam, Ramesh [mailto:Ramesh.Manyam@lsi.com]
Sent: 2008年11月27日 18:51
To: Han, Weidong
Cc: xen-devel@lists.xensource.com
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

Yes I used docs/misc/vtd.txt

Device 02:0e.0 is the MegaRAID SAS controller not 02:09.0

I am attaching the lspci output and the log messages of Xen & HVM. Please
find them with this email

Xen log messages (xmdmesg)
HVM guest kernel log messages (hvm_dmesg_with_msi_1st_time)
Domain0 Kernel log messages (dom0_var_log_messages)

Now I destroyed the HVM guest and created HVM guest again

HVM guest kernel log messages (hvm_dmesg_with_msi_2nd_time)

________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 2:43 PM
To: Manyam, Ramesh
Cc: 'xen-devel@lists.xensource.com'
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

Did you use VT-d followed docs/misc/vtd.txt?

Per xmdmesg file, device 02:09.0 didn't be mapped in context sucessfully. Is
device 02:09.0 the MegaRAID SAS controller? Can you post "lspci -v"
output?

________________________________
From: Manyam, Ramesh [mailto:Ramesh.Manyam@lsi.com]
Sent: 2008年11月27日 16:57
To: Han, Weidong
Cc: xen-devel@lists.xensource.com
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version
VT-d support is enabled

Here I am attaching three files dmesg (hvm dmesgs), dom0_varlogmessages and
xmdmesg

Thanks,
Ramesh
________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 2:18 PM
To: Manyam, Ramesh; 'xen-devel@lists.xensource.com'
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

you mean you assign MegaRAID SAS controller with VT-d to your guest?

You'd better provide more info, such as serial output, so people can be easy
to help you.

Regards,
Weidong

________________________________
From: xen-devel-bounces@lists.xensource.com
[mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Manyam, Ramesh
Sent: 2008年11月27日 16:36
To: xen-devel@lists.xensource.com
Subject: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version
A gentle reminder on this issue

Please can any one help on this problem?

________________________________
From: Manyam, Ramesh
Sent: Wednesday, November 19, 2008 7:46 PM
To: xen-devel@lists.xensource.com
Subject: megaraid sas driver failing in Xen-3.4 unstable version

On Xen-3.4 (unstable version), I have created CentOS HVM guest & WS2K8 HVM
guest and dedicated MegaRAID SAS controller but I am not able to see the disk
which is connected to MegaRAID SAS controller when I do fdisk –l (vtd support is
enabled in Xen).

Looks like the pci device(MegaRAID SAS controller) is getting dedicated
successfully as I can see the device in the list of pci devices shown by
lspci(on CentOS HVM).

00:06.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS

However the driver is not getting attached properly and fails with the following
error

======================================================================================“dmesg”
of HVM CentOS
megasas: Failed to init firmware
ACPI: PCI interrupt for device 0000:00:06.0 disabled

“/var/log/messages”
pciback 0000:02:0e.0: seizing device
 PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
 ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
 ACPI: PCI interrupt for device 0000:02:0e.0 disabled
======================================================================================

On WS2K8 HVM, I am able to see MegaRAID SAS controller under “Storage
Controllers” on WS2K8 HVM and the status of device is

========================================================================================================================================================This
device cannot start.(Code 10)
Description:
 Windows was able to successfully install device driver software, but the driver
software encountered a problem when it tried to run. The problem code is
 10.
Problem Signature:
 Problem Event Name:PnPDeviceProblemCode
 Architecture: x86
 Hardware Id: PCI\VEN_1000&DEV_0411&SUBSYS_10081000&REV_00
 Setup class GUID: {4d36e97b-e325-11ce-bfc1-08002be10318}
 PnP problem code: 0000000A
 Driver name: megasas.sys
 Driver version: 2.13.0.32
 Driver date: 01-19-2008
 OS Version: 6.0.6001.2.1.0.272.7
 Locale ID: 1033
 =======================================================================================================================================================And
also I am not able to see the disk which is connected to MegaRAID SAS controller

===========================================================================“/var/log/messages”
pciback 0000:02:0e.0: seizing device
PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
ACPI: PCI interrupt for device 0000:02:0e.0 disabled
===========================================================================

Any clues ?

Thanks,
Ramesh

_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Manyam, Ramesh

2008-Dec-01 05:32 UTC

head link

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

I found 2:9.0 in xmdmesg but not 02:09.0

Where you found 02:09.0?

Yes, 02:09.0 is not showed in lspci -v

Why you are so specific to 02:09.0?

Device 02:0e.0 is the MegaRAID SAS controller not 02:09.0


________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 7:58 PM
To: Manyam, Ramesh
Cc: ''xen-devel@lists.xensource.com''
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

what''s 02:09.0? why is it not showed in lspci -v?

________________________________
From: Manyam, Ramesh [mailto:Ramesh.Manyam@lsi.com]
Sent: 2008年11月27日 18:51
To: Han, Weidong
Cc: xen-devel@lists.xensource.com
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

Yes I used docs/misc/vtd.txt

Device 02:0e.0 is the MegaRAID SAS controller not 02:09.0

I am attaching the lspci output and the log messages of Xen & HVM. Please
find them with this email

Xen log messages (xmdmesg)
HVM guest kernel log messages (hvm_dmesg_with_msi_1st_time)
Domain0 Kernel log messages (dom0_var_log_messages)

Now I destroyed the HVM guest and created HVM guest again

HVM guest kernel log messages (hvm_dmesg_with_msi_2nd_time)




________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 2:43 PM
To: Manyam, Ramesh
Cc: ''xen-devel@lists.xensource.com''
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

Did you use VT-d followed docs/misc/vtd.txt?

Per xmdmesg file, device 02:09.0 didn''t be mapped in context
sucessfully. Is device 02:09.0 the MegaRAID SAS controller? Can you post
"lspci -v" output?



________________________________
From: Manyam, Ramesh [mailto:Ramesh.Manyam@lsi.com]
Sent: 2008年11月27日 16:57
To: Han, Weidong
Cc: xen-devel@lists.xensource.com
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version
VT-d support is enabled

Here I am attaching three files dmesg (hvm dmesgs), dom0_varlogmessages and
xmdmesg

Thanks,
Ramesh
________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 2:18 PM
To: Manyam, Ramesh; ''xen-devel@lists.xensource.com''
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

you mean you assign MegaRAID SAS controller with VT-d to your guest?

You''d better provide more info, such as serial output, so people can be
easy to help you.

Regards,
Weidong

________________________________
From: xen-devel-bounces@lists.xensource.com
[mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Manyam, Ramesh
Sent: 2008年11月27日 16:36
To: xen-devel@lists.xensource.com
Subject: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version
A gentle reminder on this issue

Please can any one help on this problem?

________________________________
From: Manyam, Ramesh
Sent: Wednesday, November 19, 2008 7:46 PM
To: xen-devel@lists.xensource.com
Subject: megaraid sas driver failing in Xen-3.4 unstable version


On Xen-3.4 (unstable version), I have created CentOS HVM guest & WS2K8 HVM
guest and dedicated MegaRAID SAS controller but I am not able to see the disk
which is connected to MegaRAID SAS controller when I do fdisk -l (vtd support is
enabled in Xen).

Looks like the pci device(MegaRAID SAS controller) is getting dedicated
successfully as I can see the device in the list of pci devices shown by
lspci(on CentOS HVM).

00:06.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS


However the driver is not getting attached properly and fails with the following
error

======================================================================================“dmesg”
of HVM CentOS
megasas: Failed to init firmware
ACPI: PCI interrupt for device 0000:00:06.0 disabled


“/var/log/messages”
pciback 0000:02:0e.0: seizing device
 PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
 ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
 ACPI: PCI interrupt for device 0000:02:0e.0 disabled
======================================================================================


On WS2K8 HVM, I am able to see MegaRAID SAS controller under “Storage
Controllers” on WS2K8 HVM and the status of device is

========================================================================================================================================================This
device cannot start.(Code 10)
Description:
 Windows was able to successfully install device driver software, but the driver
software encountered a problem when it tried to run. The problem code is
 10.
Problem Signature:
 Problem Event Name:PnPDeviceProblemCode
 Architecture: x86
 Hardware Id: PCI\VEN_1000&DEV_0411&SUBSYS_10081000&REV_00
 Setup class GUID: {4d36e97b-e325-11ce-bfc1-08002be10318}
 PnP problem code: 0000000A
 Driver name: megasas.sys
 Driver version: 2.13.0.32
 Driver date: 01-19-2008
 OS Version: 6.0.6001.2.1.0.272.7
 Locale ID: 1033
 =======================================================================================================================================================And
also I am not able to see the disk which is connected to MegaRAID SAS controller

===========================================================================“/var/log/messages”
pciback 0000:02:0e.0: seizing device
PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
ACPI: PCI interrupt for device 0000:02:0e.0 disabled
===========================================================================

Any clues ?

Thanks,
Ramesh


_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Han, Weidong

2008-Dec-01 07:05 UTC

head link

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

02:09.0 is just 2:9.0. I found lots of page faults of this device on xmdmesg.

Per your lspci -v output, I can know 02:0e.0 is under the PCI bridge
00:01.0.device 02:09.0 is under the same bridge. You must assign all the pci
devices under the same PCI bridge to the same guest. But it's curious we
cannot find 02:09.0 in lspci whilc there are its DMR page faults. The reason
(REASON 2) is that it is not mapped in VT-d context table.

Regards,
Weidong

________________________________
From: Manyam, Ramesh [mailto:Ramesh.Manyam@lsi.com]
Sent: 2008年12月1日 13:32
To: Han, Weidong
Cc: xen-devel@lists.xensource.com
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version


I found 2:9.0 in xmdmesg but not 02:09.0

Where you found 02:09.0?

Yes, 02:09.0 is not showed in lspci –v

Why you are so specific to 02:09.0?

Device 02:0e.0 is the MegaRAID SAS controller not 02:09.0


________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 7:58 PM
To: Manyam, Ramesh
Cc: 'xen-devel@lists.xensource.com'
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

what's 02:09.0? why is it not showed in lspci -v?

________________________________
From: Manyam, Ramesh [mailto:Ramesh.Manyam@lsi.com]
Sent: 2008年11月27日 18:51
To: Han, Weidong
Cc: xen-devel@lists.xensource.com
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

Yes I used docs/misc/vtd.txt

Device 02:0e.0 is the MegaRAID SAS controller not 02:09.0

I am attaching the lspci output and the log messages of Xen & HVM. Please
find them with this email

Xen log messages (xmdmesg)
HVM guest kernel log messages (hvm_dmesg_with_msi_1st_time)
Domain0 Kernel log messages (dom0_var_log_messages)

Now I destroyed the HVM guest and created HVM guest again

HVM guest kernel log messages (hvm_dmesg_with_msi_2nd_time)




________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 2:43 PM
To: Manyam, Ramesh
Cc: 'xen-devel@lists.xensource.com'
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

Did you use VT-d followed docs/misc/vtd.txt?

Per xmdmesg file, device 02:09.0 didn't be mapped in context sucessfully. Is
device 02:09.0 the MegaRAID SAS controller? Can you post "lspci -v"
output?



________________________________
From: Manyam, Ramesh [mailto:Ramesh.Manyam@lsi.com]
Sent: 2008年11月27日 16:57
To: Han, Weidong
Cc: xen-devel@lists.xensource.com
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version
VT-d support is enabled

Here I am attaching three files dmesg (hvm dmesgs), dom0_varlogmessages and
xmdmesg

Thanks,
Ramesh
________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 2:18 PM
To: Manyam, Ramesh; 'xen-devel@lists.xensource.com'
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

you mean you assign MegaRAID SAS controller with VT-d to your guest?

You'd better provide more info, such as serial output, so people can be easy
to help you.

Regards,
Weidong

________________________________
From: xen-devel-bounces@lists.xensource.com
[mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Manyam, Ramesh
Sent: 2008年11月27日 16:36
To: xen-devel@lists.xensource.com
Subject: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version
A gentle reminder on this issue

Please can any one help on this problem?

________________________________
From: Manyam, Ramesh
Sent: Wednesday, November 19, 2008 7:46 PM
To: xen-devel@lists.xensource.com
Subject: megaraid sas driver failing in Xen-3.4 unstable version


On Xen-3.4 (unstable version), I have created CentOS HVM guest & WS2K8 HVM
guest and dedicated MegaRAID SAS controller but I am not able to see the disk
which is connected to MegaRAID SAS controller when I do fdisk –l (vtd support is
enabled in Xen).

Looks like the pci device(MegaRAID SAS controller) is getting dedicated
successfully as I can see the device in the list of pci devices shown by
lspci(on CentOS HVM).

00:06.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS


However the driver is not getting attached properly and fails with the following
error

======================================================================================“dmesg”
of HVM CentOS
megasas: Failed to init firmware
ACPI: PCI interrupt for device 0000:00:06.0 disabled


“/var/log/messages”
pciback 0000:02:0e.0: seizing device
 PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
 ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
 ACPI: PCI interrupt for device 0000:02:0e.0 disabled
======================================================================================


On WS2K8 HVM, I am able to see MegaRAID SAS controller under “Storage
Controllers” on WS2K8 HVM and the status of device is

========================================================================================================================================================This
device cannot start.(Code 10)
Description:
 Windows was able to successfully install device driver software, but the driver
software encountered a problem when it tried to run. The problem code is
 10.
Problem Signature:
 Problem Event Name:PnPDeviceProblemCode
 Architecture: x86
 Hardware Id: PCI\VEN_1000&DEV_0411&SUBSYS_10081000&REV_00
 Setup class GUID: {4d36e97b-e325-11ce-bfc1-08002be10318}
 PnP problem code: 0000000A
 Driver name: megasas.sys
 Driver version: 2.13.0.32
 Driver date: 01-19-2008
 OS Version: 6.0.6001.2.1.0.272.7
 Locale ID: 1033
 =======================================================================================================================================================And
also I am not able to see the disk which is connected to MegaRAID SAS controller

===========================================================================“/var/log/messages”
pciback 0000:02:0e.0: seizing device
PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
ACPI: PCI interrupt for device 0000:02:0e.0 disabled
===========================================================================

Any clues ?

Thanks,
Ramesh


_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Manyam, Ramesh

2008-Dec-01 12:22 UTC

head link

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

I am using 4 port MegaRAID SAS Controller card and only one disk is connected to
this controller (only one port we are using). When I tried to bind the device
0000:02:09.0 to pciback driver it saying “no such device”. Is there any other
way to bind this device to pciback driver?

When I remove MegaRAID SAS Controller card from the machine I couldn’t find this
device (02:09.0) in “xm dmesg” after dedicating onboard SAS Controller to Linux
HVM.



Thanks,
Ramesh

________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Monday, December 01, 2008 12:35 PM
To: Manyam, Ramesh
Cc: ''xen-devel@lists.xensource.com''
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

02:09.0 is just 2:9.0. I found lots of page faults of this device on xmdmesg.

Per your lspci -v output, I can know 02:0e.0 is under the PCI bridge
00:01.0.device 02:09.0 is under the same bridge. You must assign all the pci
devices under the same PCI bridge to the same guest. But it''s curious
we cannot find 02:09.0 in lspci whilc there are its DMR page faults. The reason
(REASON 2) is that it is not mapped in VT-d context table.

Regards,
Weidong

________________________________
From: Manyam, Ramesh [mailto:Ramesh.Manyam@lsi.com]
Sent: 2008年12月1日 13:32
To: Han, Weidong
Cc: xen-devel@lists.xensource.com
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

I found 2:9.0 in xmdmesg but not 02:09.0

Where you found 02:09.0?

Yes, 02:09.0 is not showed in lspci -v

Why you are so specific to 02:09.0?

Device 02:0e.0 is the MegaRAID SAS controller not 02:09.0


________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 7:58 PM
To: Manyam, Ramesh
Cc: ''xen-devel@lists.xensource.com''
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

what''s 02:09.0? why is it not showed in lspci -v?

________________________________
From: Manyam, Ramesh [mailto:Ramesh.Manyam@lsi.com]
Sent: 2008年11月27日 18:51
To: Han, Weidong
Cc: xen-devel@lists.xensource.com
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

Yes I used docs/misc/vtd.txt

Device 02:0e.0 is the MegaRAID SAS controller not 02:09.0

I am attaching the lspci output and the log messages of Xen & HVM. Please
find them with this email

Xen log messages (xmdmesg)
HVM guest kernel log messages (hvm_dmesg_with_msi_1st_time)
Domain0 Kernel log messages (dom0_var_log_messages)

Now I destroyed the HVM guest and created HVM guest again

HVM guest kernel log messages (hvm_dmesg_with_msi_2nd_time)




________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 2:43 PM
To: Manyam, Ramesh
Cc: ''xen-devel@lists.xensource.com''
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

Did you use VT-d followed docs/misc/vtd.txt?

Per xmdmesg file, device 02:09.0 didn''t be mapped in context
sucessfully. Is device 02:09.0 the MegaRAID SAS controller? Can you post
"lspci -v" output?



________________________________
From: Manyam, Ramesh [mailto:Ramesh.Manyam@lsi.com]
Sent: 2008年11月27日 16:57
To: Han, Weidong
Cc: xen-devel@lists.xensource.com
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version
VT-d support is enabled

Here I am attaching three files dmesg (hvm dmesgs), dom0_varlogmessages and
xmdmesg

Thanks,
Ramesh
________________________________
From: Han, Weidong [mailto:weidong.han@intel.com]
Sent: Thursday, November 27, 2008 2:18 PM
To: Manyam, Ramesh; ''xen-devel@lists.xensource.com''
Subject: RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable
version

you mean you assign MegaRAID SAS controller with VT-d to your guest?

You''d better provide more info, such as serial output, so people can be
easy to help you.

Regards,
Weidong

________________________________
From: xen-devel-bounces@lists.xensource.com
[mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Manyam, Ramesh
Sent: 2008年11月27日 16:36
To: xen-devel@lists.xensource.com
Subject: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version
A gentle reminder on this issue

Please can any one help on this problem?

________________________________
From: Manyam, Ramesh
Sent: Wednesday, November 19, 2008 7:46 PM
To: xen-devel@lists.xensource.com
Subject: megaraid sas driver failing in Xen-3.4 unstable version


On Xen-3.4 (unstable version), I have created CentOS HVM guest & WS2K8 HVM
guest and dedicated MegaRAID SAS controller but I am not able to see the disk
which is connected to MegaRAID SAS controller when I do fdisk -l (vtd support is
enabled in Xen).

Looks like the pci device(MegaRAID SAS controller) is getting dedicated
successfully as I can see the device in the list of pci devices shown by
lspci(on CentOS HVM).

00:06.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS


However the driver is not getting attached properly and fails with the following
error

======================================================================================“dmesg”
of HVM CentOS
megasas: Failed to init firmware
ACPI: PCI interrupt for device 0000:00:06.0 disabled


“/var/log/messages”
pciback 0000:02:0e.0: seizing device
 PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
 ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
 ACPI: PCI interrupt for device 0000:02:0e.0 disabled
======================================================================================


On WS2K8 HVM, I am able to see MegaRAID SAS controller under “Storage
Controllers” on WS2K8 HVM and the status of device is

========================================================================================================================================================This
device cannot start.(Code 10)
Description:
 Windows was able to successfully install device driver software, but the driver
software encountered a problem when it tried to run. The problem code is
 10.
Problem Signature:
 Problem Event Name:PnPDeviceProblemCode
 Architecture: x86
 Hardware Id: PCI\VEN_1000&DEV_0411&SUBSYS_10081000&REV_00
 Setup class GUID: {4d36e97b-e325-11ce-bfc1-08002be10318}
 PnP problem code: 0000000A
 Driver name: megasas.sys
 Driver version: 2.13.0.32
 Driver date: 01-19-2008
 OS Version: 6.0.6001.2.1.0.272.7
 Locale ID: 1033
 =======================================================================================================================================================And
also I am not able to see the disk which is connected to MegaRAID SAS controller

===========================================================================“/var/log/messages”
pciback 0000:02:0e.0: seizing device
PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25
ACPI: PCI interrupt for device 0000:02:0e.0 disabled
===========================================================================

Any clues ?

Thanks,
Ramesh


_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Reasonably Related Threads

Search for more seemingly similar threads

Xen devel - Nov 2008 - FW: megaraid sas driver failing in Xen-3.4 unstable version

[Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstableversion

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

RE: [Xen-devel] FW: megaraid sas driver failing in Xen-3.4 unstable version

Reasonably Related Threads