Miroslav Lachman
2008-Oct-14 23:09 UTC
atacontrol: ioctl(IOCATADEVICES): Device not configured
FreeBSD 7.1-BETA amd64 GENERIC on HP ProLiant ML110 G5
When I tried to run 'atacontrol list' I got an error:
atacontrol: ioctl(IOCATADEVICES): Device not configured
It is after I switched HDD mode in BIOS to "Serial ATA" (it was
"Auto"
before)
Does it means that atacontrol list is not available for Serial ATA
native mode? (I don't think so, because I am using atacontrol on another
machines where disk are at AHCI mode AFAIK - Sun Fire X2100 M2 for example)
## pciconf -lv
atapci0@pci0:0:31:2: class=0x01018f card=0x31f4103c chip=0x29208086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) 4 port Serial ATA Storage
Controller 1'
class = mass storage
subclass = ATA
none0@pci0:0:31:3: class=0x0c0500 card=0x31f4103c chip=0x29308086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) SMBus Controller'
class = serial bus
subclass = SMBus
atapci1@pci0:0:31:5: class=0x010185 card=0x31f4103c chip=0x29268086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) 2 port Serial ATA Storage
Controller 2'
class = mass storage
subclass = ATA
bge0@pci0:14:0:0: class=0x020000 card=0x7051103c chip=0x165a14e4
rev=0x00 hdr=0x00
vendor = 'Broadcom Corporation'
device = 'NetXtreme BCM5722 Gigabit Ethernet PCIe'
class = network
subclass = ethernet
## BIOS HDD mode: Serial ATA
## /var/run/dmesg.boog
atapci0: <Intel ICH9 SATA300 controller> port
0x1c50-0x1c57,0x1c44-0x1c47,0x1c48-0x1c4f,0x1c40-0x1c43,0x1c10-0x1c1f,0x1c00-0x1c0f
irq 17 at device 31.2 on pci0
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci1: <Intel ICH9 SATA300 controller> port
0x1c68-0x1c6f,0x1c5c-0x1c5f,0x1c60-0x1c67,0x1c58-0x1c5b,0x1c30-0x1c3f,0x1c20-0x1c2f
irq 18 at device 31.5 on pci0
atapci1: [ITHREAD]
ata4: <ATA channel 0> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 1> on atapci1
ata5: [ITHREAD]
[...]
ad4: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata2-master SATA300
ad5: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata2-slave SATA300
ad6: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata3-master SATA300
ad7: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata3-slave SATA300
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <USB 2.0 Flash Disk 1100> Removable Direct Access SCSI-0 device
da0: 40.000MB/s transfers
da0: 7936MB (16252928 512 byte sectors: 255H 63S/T 1011C)
acd0: DVDR <HL-DT-ST DVD-RAM GH15L/FA01> at ata4-master SATA150
## BIOS HDD mode: Auto
atapci0: <Intel ICH9 SATA300 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1c10-0x1c1f,0x1c00-0x1c0f at
device 31.2 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci1: <Intel ICH9 SATA300 controller> port
0x1c68-0x1c6f,0x1c5c-0x1c5f,0x1c60-0x1c67,0x1c58-0x1c5b,0x1c30-0x1c3f,0x1c20-0x1c2f
irq 18 at device 31.5 on pci0
atapci1: [ITHREAD]
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: [ITHREAD]
[...]
ad0: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata0-master SATA300
ad1: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata0-slave SATA300
ad2: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata1-master SATA300
ad3: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata1-slave SATA300
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <USB 2.0 Flash Disk 1100> Removable Direct Access SCSI-0 device
da0: 40.000MB/s transfers
da0: 7936MB (16252928 512 byte sectors: 255H 63S/T 1011C)
acd0: DVDR <HL-DT-ST DVD-RAM GH15L/FA01> at ata2-master SATA150
The motherboard has 6x SATA ports, 2 are marked "for optical/removable
drives" and 4 are for HDDs.
System is booted from USB flash disk.
It is first time I see SATA devices attached as Master & Slave on same
ATA channel, previously (on different machines) it was always as Master
on separated channels. This configuration is worse if I want to utilize
all drives at the same time (in RAIDZ). One drive can achieve 110MB/s
read, both drives can achieve only 80MB/s each. ;(
Next strange thing is difference in Interrupts in systat output. With
mode "Auto', each ATA channel is listed on separated IRQ, with mode
"Serial ATA" channels are not listed but it seems that both are on the
same interrupt as bge0. Am I right? So it seems better to not use
"Serial ATA" mode settings.
## part of systat during read test by 'dd if=/dev/adN of=/dev/null'
## BIOS HDD mode: Serial ATA
Interrupts
8737 total
uhci0 uhci
4734 bge0 uhci1
uhci2 ehci
2001 cpu0: time
2002 cpu1: time
## BIOS HDD mode: Auto
Interrupts
9262 total
2660 ata0 irq14
2603 ata1 irq15
uhci0 uhci
1 bge0 uhci1
uhci2 ehci
1999 cpu0: time
1999 cpu1: time
Let me know if (and what) more details are needed.
Miroslav Lachman
Jeremy Chadwick
2008-Oct-15 04:17 UTC
atacontrol: ioctl(IOCATADEVICES): Device not configured
On Wed, Oct 15, 2008 at 01:09:47AM +0200, Miroslav Lachman wrote:> FreeBSD 7.1-BETA amd64 GENERIC on HP ProLiant ML110 G5 > > When I tried to run 'atacontrol list' I got an error: > atacontrol: ioctl(IOCATADEVICES): Device not configuredThere was a bug in atacontrol which was causing this for most people, although there's the possibility that this is a new bug. See revision 1.43.2.3 below: http://www.freebsd.org/cgi/cvsweb.cgi/src/sbin/atacontrol/atacontrol.c Can you verify what version of src/sbin/atacontrol/atacontrol.c your world was built off of? I'm thinking because it was so new (barely 2 weeks) that it didn't get pulled in during the BETA build, but it definitely should have gotten pulled in for BETA2. ftp://ftp4.freebsd.org/pub/FreeBSD/releases/amd64/ISO-IMAGES/7.1/> It is after I switched HDD mode in BIOS to "Serial ATA" (it was "Auto" > before) > > Does it means that atacontrol list is not available for Serial ATA > native mode? (I don't think so, because I am using atacontrol on another > machines where disk are at AHCI mode AFAIK - Sun Fire X2100 M2 for > example) > > > ## pciconf -lv > atapci0@pci0:0:31:2: class=0x01018f card=0x31f4103c chip=0x29208086 > rev=0x02 hdr=0x00 > vendor = 'Intel Corporation' > device = '82801IB/IR/IH (ICH9 Family) 4 port Serial ATA Storage > Controller 1' > class = mass storage > subclass = ATA > none0@pci0:0:31:3: class=0x0c0500 card=0x31f4103c chip=0x29308086 > rev=0x02 hdr=0x00 > vendor = 'Intel Corporation' > device = '82801IB/IR/IH (ICH9 Family) SMBus Controller' > class = serial bus > subclass = SMBus > atapci1@pci0:0:31:5: class=0x010185 card=0x31f4103c chip=0x29268086 > rev=0x02 hdr=0x00 > vendor = 'Intel Corporation' > device = '82801IB/IR/IH (ICH9 Family) 2 port Serial ATA Storage > Controller 2' > class = mass storage > subclass = ATA > > bge0@pci0:14:0:0: class=0x020000 card=0x7051103c chip=0x165a14e4 > rev=0x00 hdr=0x00 > vendor = 'Broadcom Corporation' > device = 'NetXtreme BCM5722 Gigabit Ethernet PCIe' > class = network > subclass = ethernet > > ## BIOS HDD mode: Serial ATA > ## /var/run/dmesg.boog > atapci0: <Intel ICH9 SATA300 controller> port > 0x1c50-0x1c57,0x1c44-0x1c47,0x1c48-0x1c4f,0x1c40-0x1c43,0x1c10-0x1c1f,0x1c00-0x1c0f > irq 17 at device 31.2 on pci0 > atapci0: [ITHREAD] > ata2: <ATA channel 0> on atapci0 > ata2: [ITHREAD] > ata3: <ATA channel 1> on atapci0 > ata3: [ITHREAD] > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > atapci1: <Intel ICH9 SATA300 controller> port > 0x1c68-0x1c6f,0x1c5c-0x1c5f,0x1c60-0x1c67,0x1c58-0x1c5b,0x1c30-0x1c3f,0x1c20-0x1c2f > irq 18 at device 31.5 on pci0 > atapci1: [ITHREAD] > ata4: <ATA channel 0> on atapci1 > ata4: [ITHREAD] > ata5: <ATA channel 1> on atapci1 > ata5: [ITHREAD] > [...] > ad4: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata2-master SATA300 > ad5: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata2-slave SATA300 > ad6: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata3-master SATA300 > ad7: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata3-slave SATA300 > da0 at umass-sim0 bus 0 target 0 lun 0 > da0: <USB 2.0 Flash Disk 1100> Removable Direct Access SCSI-0 device > da0: 40.000MB/s transfers > da0: 7936MB (16252928 512 byte sectors: 255H 63S/T 1011C) > acd0: DVDR <HL-DT-ST DVD-RAM GH15L/FA01> at ata4-master SATA150 > > > ## BIOS HDD mode: Auto > atapci0: <Intel ICH9 SATA300 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1c10-0x1c1f,0x1c00-0x1c0f at > device 31.2 on pci0 > ata0: <ATA channel 0> on atapci0 > ata0: [ITHREAD] > ata1: <ATA channel 1> on atapci0 > ata1: [ITHREAD] > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > atapci1: <Intel ICH9 SATA300 controller> port > 0x1c68-0x1c6f,0x1c5c-0x1c5f,0x1c60-0x1c67,0x1c58-0x1c5b,0x1c30-0x1c3f,0x1c20-0x1c2f > irq 18 at device 31.5 on pci0 > atapci1: [ITHREAD] > ata2: <ATA channel 0> on atapci1 > ata2: [ITHREAD] > ata3: <ATA channel 1> on atapci1 > ata3: [ITHREAD] > [...] > ad0: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata0-master SATA300 > ad1: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata0-slave SATA300 > ad2: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata1-master SATA300 > ad3: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata1-slave SATA300 > da0 at umass-sim0 bus 0 target 0 lun 0 > da0: <USB 2.0 Flash Disk 1100> Removable Direct Access SCSI-0 device > da0: 40.000MB/s transfers > da0: 7936MB (16252928 512 byte sectors: 255H 63S/T 1011C) > acd0: DVDR <HL-DT-ST DVD-RAM GH15L/FA01> at ata2-master SATA150 > > > The motherboard has 6x SATA ports, 2 are marked "for optical/removable > drives" and 4 are for HDDs. > System is booted from USB flash disk. > It is first time I see SATA devices attached as Master & Slave on same > ATA channel, previously (on different machines) it was always as Master > on separated channels. This configuration is worse if I want to utilize > all drives at the same time (in RAIDZ). One drive can achieve 110MB/s > read, both drives can achieve only 80MB/s each. ;( > > Next strange thing is difference in Interrupts in systat output. With > mode "Auto', each ATA channel is listed on separated IRQ, with mode > "Serial ATA" channels are not listed but it seems that both are on the > same interrupt as bge0. Am I right? So it seems better to not use > "Serial ATA" mode settings. > > ## part of systat during read test by 'dd if=/dev/adN of=/dev/null' > ## BIOS HDD mode: Serial ATA > Interrupts > 8737 total > uhci0 uhci > 4734 bge0 uhci1 > uhci2 ehci > 2001 cpu0: time > 2002 cpu1: time > > ## BIOS HDD mode: Auto > Interrupts > 9262 total > 2660 ata0 irq14 > 2603 ata1 irq15 > uhci0 uhci > 1 bge0 uhci1 > uhci2 ehci > 1999 cpu0: time > 1999 cpu1: time > > > Let me know if (and what) more details are needed. > > Miroslav Lachman > _______________________________________________ > freebsd-stable@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"-- | Jeremy Chadwick jdc at parodius.com | | Parodius Networking http://www.parodius.com/ | | UNIX Systems Administrator Mountain View, CA, USA | | Making life hard for others since 1977. PGP: 4BD6C0CB |