thr3ads.net - CentOS - [CentOS] USB to Ethernet problem [Mar 2014]

If this information is useful, please help other people find it:
Share via:

Giri Prasad

2014-Mar-18 08:49 UTC

[CentOS] USB to Ethernet problem

Hello All,

?I installed Centos 6.5 64 bit on a Dell Vostro 1550 laptop with i3 core. The
kernel installed was 2.6.32-431.el6.x86_64. I was not able to compile kernel
modules, even after installing the kernel headers, kernel source rpms.

?So I downloaded the kernel linux-3.10.31.tar.xz, extracted it, and did the
following:

make defconfig

change CONFIG_USB_USBNET=y, in the .config.

make

? ASIX AX88xxx Based USB 2.0 Ethernet Adapters (USB_NET_AX8817X) [Y/n/m/?] (NEW)
n
? ASIX AX88179/178A USB 3.0/2.0 to Gigabit Ethernet (USB_NET_AX88179_178A)
[Y/n/m/?] (NEW) n

????? All the other options selected the default.

make modules

make modules_install

make install

Then I booted from 3.10 kernel, which went thru fine. After logging in into the
3.10 kernel, I compiled and insmod the asix driver for usb to ethernet. Upon
insmod, the eth1 interface comes up, but with no IPV4 address assigned. So I
assigned a static IP address using ifconfig. Then added a route for the default
gateway.

Now, after assigning a static IPV4 address, this eth1 is pinging to the default
gateway 192.168.1.1. But eth1 is not pinging/connecting to the external
internet. Can someone please provide some answers.

?I am using the device from www.svbinternational.com. The device is labeled USB
2.0 to network 10/100Mbps ethernet adapter. Device id, as can be seen from lsusb
is: Device 003: ID 0b95:772b ASIX Electronics Corp. AX88772B.

Thanks in advance.

Regards,
Giri


AX88772C_772B_772A_760_772_178_LINUX_DRIVER_v4.12.0_Source.tar.bz2

[root at gpcentospc1
AX88772C_772B_772A_760_772_178_LINUX_DRIVER_v4.12.0_Source]# insmod asix.ko

[root at gpcentospc1 ~]# lsmod
Module????????????????? Size? Used by
asix?????????????????? 47587? 0 

[root at gpcentospc1 ~]# ifconfig?????????? (DEFAULT NO IP ADDRESS) 
eth1????? Link encap:Ethernet? HWaddr 00:00:00:00:00:01? 
????????? inet6 addr: fe80::200:ff:fe00:1/64 Scope:Link
????????? UP BROADCAST RUNNING MULTICAST? MTU:1500? Metric:1
????????? RX packets:4 errors:0 dropped:0 overruns:0 frame:0
????????? TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
????????? collisions:0 txqueuelen:1000 
????????? RX bytes:228 (228.0 b)? TX bytes:954 (954.0 b)

lo??????? Link encap:Local Loopback? 
????????? inet addr:127.0.0.1? Mask:255.0.0.0
????????? inet6 addr: ::1/128 Scope:Host
????????? UP LOOPBACK RUNNING? MTU:65536? Metric:1
????????? RX packets:52 errors:0 dropped:0 overruns:0 frame:0
????????? TX packets:52 errors:0 dropped:0 overruns:0 carrier:0
????????? collisions:0 txqueuelen:0 
????????? RX bytes:4040 (3.9 KiB)? TX bytes:4040 (3.9 KiB)

[root at gpcentospc1 ~]# ifconfig eth1 192.168.1.20 netmask 255.255.255.0
broadcast 192.168.1.255
[root at gpcentospc1 ~]# ifconfig
eth1????? Link encap:Ethernet? HWaddr 00:00:00:00:00:01? 
????????? inet addr:192.168.1.20? Bcast:192.168.1.255? Mask:255.255.255.0
????????? inet6 addr: fe80::200:ff:fe00:1/64 Scope:Link
????????? UP BROADCAST RUNNING MULTICAST? MTU:1500? Metric:1
????????? RX packets:8 errors:0 dropped:0 overruns:0 frame:0
????????? TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
????????? collisions:0 txqueuelen:1000 
????????? RX bytes:438 (438.0 b)? TX bytes:1992 (1.9 KiB)

lo??????? Link encap:Local Loopback? 
????????? inet addr:127.0.0.1? Mask:255.0.0.0
????????? inet6 addr: ::1/128 Scope:Host
????????? UP LOOPBACK RUNNING? MTU:65536? Metric:1
????????? RX packets:52 errors:0 dropped:0 overruns:0 frame:0
????????? TX packets:52 errors:0 dropped:0 overruns:0 carrier:0
????????? collisions:0 txqueuelen:0 
????????? RX bytes:4040 (3.9 KiB)? TX bytes:4040 (3.9 KiB)

[root at gpcentospc1 ~]# route add default gw 192.168.1.1

[root at gpcentospc1 ~]# route
Kernel IP routing table
Destination???? Gateway???????? Genmask???????? Flags Metric Ref??? Use Iface
default???????? 192.168.1.1???? 0.0.0.0???????? UG??? 0????? 0??????? 0 eth1
192.168.1.0???? *?????????????? 255.255.255.0?? U???? 0????? 0??????? 0 eth1


[root at gpcentospc1 ~]# lsusb
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0b95:772b ASIX Electronics Corp. AX88772B
Bus 001 Device 004: ID 0461:4d81 Primax Electronics, Ltd Dell N889 Optical Mouse
Bus 001 Device 005: ID 0a5c:21bc Broadcom Corp. BCM2070 Bluetooth 2.1 + EDR
Bus 001 Device 006: ID 0c45:643e Microdia 
Bus 002 Device 003: ID 0bda:0138 Realtek Semiconductor Corp. RTS5138 Card Reader
Controller



[root at gpcentospc1 ~]# ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=254 time=3.73 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=254 time=1.88 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=254 time=1.95 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=254 time=1.95 ms
64 bytes from 192.168.1.1: icmp_seq=5 ttl=254 time=1.87 ms
64 bytes from 192.168.1.1: icmp_seq=6 ttl=254 time=1.93 ms
64 bytes from 192.168.1.1: icmp_seq=7 ttl=254 time=1.91 ms
64 bytes from 192.168.1.1: icmp_seq=8 ttl=254 time=1.86 ms
64 bytes from 192.168.1.1: icmp_seq=9 ttl=254 time=1.97 ms
64 bytes from 192.168.1.1: icmp_seq=10 ttl=254 time=1.88 ms
^C
--- 192.168.1.1 ping statistics ---
10 packets transmitted, 10 received, 0% packet loss, time 9778ms
rtt min/avg/max/mdev = 1.867/2.095/3.731/0.549 ms


[root at gpcentospc1 ~]# ping google.com
ping: unknown host google.com


[root at gpcentospc1 ~]#? uname -a
Linux gpcentospc1.cruzesoft.com 3.10.31 #8 SMP Tue Mar 18 01:52:26 IST 2014
x86_64 x86_64 x86_64 GNU/Linux
[root at gpcentospc1 ~]# 
[root at gpcentospc1 ~]# 

[root at gpcentospc1 ~]# ethtool -i eth1
driver: asix
version: 22-Aug-2005
firmware-version: ASIX AX88772B USB 2.0 Ethernet
bus-info: usb-0000:00:1a.0-1.1
supports-statistics: no
supports-test: no
supports-eeprom-access: yes
supports-register-dump: no
supports-priv-flags: no
[root at gpcentospc1 ~]# 
[root at gpcentospc1 ~]# 


The same device on Windows 7 64 bit, same laptop, gets the IP Address and mask
as 169.254.74.198, whereas the wireless interface is properly assigned the IPV4
address as 192.168.1.2 :

Autoconfiguration IPv4 Address. . : 169.254.74.198
Subnet Mask . . . . . . . . . . . : 255.255.0.0


C:\Users\giri>ipconfig

Windows IP Configuration


Ethernet adapter Local Area Connection:

?? Connection-specific DNS Suffix? . :
?? Link-local IPv6 Address . . . . . : fe80::606c:d214:57c9:4ac6%17
?? Autoconfiguration IPv4 Address. . : 169.254.74.198
?? Subnet Mask . . . . . . . . . . . : 255.255.0.0
?? Default Gateway . . . . . . . . . : fe80::ed2:b5ff:fe13:d3d4%17

Wireless LAN adapter Wireless Network Connection:

?? Connection-specific DNS Suffix? . :
?? Link-local IPv6 Address . . . . . : fe80::7448:5c68:7e43:1108%15
?? IPv4 Address. . . . . . . . . . . : 192.168.1.2
?? Subnet Mask . . . . . . . . . . . : 255.255.255.0
?? Default Gateway . . . . . . . . . : fe80::ed2:b5ff:fe13:d3d4%15
?????????????????????????????????????? 192.168.1.1

Anthony K

2014-Mar-18 09:17 UTC

head link

[CentOS] USB to Ethernet problem

On 18/03/14 19:49, Giri Prasad wrote:> Now, after assigning a static IPV4 address, this eth1 is pinging to the
default gateway 192.168.1.1. But eth1 is not pinging/connecting to the external
internet. Can someone please provide some answers.
>
>Can you ping an IP Address - such as 8.8.8.8?

If you can, then most likely a DNS config issue!  Since you mention you 
had to assign an IP Address manually, the file /etc/resolv.conf may not 
have the necessary DNS info to resolve Internet names!

Cheers,
ak.

Ned Slider

2014-Mar-18 15:27 UTC

head link

[CentOS] USB to Ethernet problem

On 18/03/14 08:49, Giri Prasad wrote:> Hello All,
>
>   I installed Centos 6.5 64 bit on a Dell Vostro 1550 laptop with i3 core.
The kernel installed was 2.6.32-431.el6.x86_64. I was not able to compile kernel
modules, even after installing the kernel headers, kernel source rpms.
>
>   So I downloaded the kernel linux-3.10.31.tar.xz, extracted it, and did
the following:
>
> make defconfig
>
> change CONFIG_USB_USBNET=y, in the .config.
>
> make
>
>    ASIX AX88xxx Based USB 2.0 Ethernet Adapters (USB_NET_AX8817X) [Y/n/m/?]
(NEW) n
>    ASIX AX88179/178A USB 3.0/2.0 to Gigabit Ethernet (USB_NET_AX88179_178A)
[Y/n/m/?] (NEW) n
>
>        All the other options selected the default.
>
> make modules
>
> make modules_install
>
> make install
>
I backported this driver for el6 at elrepo. Rather than compile and 
maintain a complete kernel from source, you could have just set up 
elrepo and done 'yum install kmod-asix'.


http://elrepo.org/tiki/kmod-asix
https://github.com/elrepo/packages/commits/master/asix-kmod

Seemingly Similar Threads

Search for more reasonably related threads

CentOS - Mar 2014 - USB to Ethernet problem

[CentOS] USB to Ethernet problem

[CentOS] USB to Ethernet problem

[CentOS] USB to Ethernet problem

Seemingly Similar Threads