On Wednesday 18 December 2002 22:12, LARTC@VLMINTERNATIONAL.COM
wrote:> I''ve got some customers that have lots of bandwidth that are
uploading and
> downloading files to our https:// help desk and are using up all of my T-1
> at times. This leaves other customers sucking wind. I''ve taken a
look at
> the ''15.10. Example of a full nat solution with QoS''
section. Would it work
> for me if I change the section that says eth0 to my internet adapter
> Serial0? If I can do that, will that allow fair sharing between all my
> customers of the https:// help desk?
>
> My setup:
>
> ////////// ///////////////// ///////
> https:// |-- |eth0 * Serial0 |-- |INET |
> ////////// ///////////////// ///////
>
> My proposed script:
>
> CEIL=1020 # actual is 1024Kbit
> IFACE=Serial0
>
> tc qdisc add dev $IFACE root handle 1: htb default 15
> tc class add dev $IFACE parent 1: classid 1:1 htb rate ${CEIL}kbit ceil
> ${CEIL}kbit
> tc class add dev $IFACE parent 1:1 classid 1:10 htb rate 170kbit ceil
> 170kbit prio 0
> tc class add dev $IFACE parent 1:1 classid 1:11 htb rate 170kbit ceil
> ${CEIL}kbit prio 1
> tc class add dev $IFACE parent 1:1 classid 1:12 htb rate 170kbit ceil
> ${CEIL}kbit prio 2
> tc class add dev $IFACE parent 1:1 classid 1:13 htb rate 170kbit ceil
> ${CEIL}kbit prio 2
> tc class add dev $IFACE parent 1:1 classid 1:14 htb rate 170kbit ceil
> ${CEIL}kbit prio 3
> tc class add dev $IFACE parent 1:1 classid 1:15 htb rate 170kbit ceil
> ${CEIL}kbit prio 3
>
> tc qdisc add dev $IFACE parent 1:12 handle 120: sfq perturb 10
> tc qdisc add dev $IFACE parent 1:13 handle 130: sfq perturb 10
> tc qdisc add dev $IFACE parent 1:14 handle 140: sfq perturb 10
> tc qdisc add dev $IFACE parent 1:15 handle 150: sfq perturb 10
>
> tc filter add dev $IFACE parent 1:0 protocol ip prio 1 handle 1 fw classid
> 1:10
> tc filter add dev $IFACE parent 1:0 protocol ip prio 2 handle 2 fw classid
> 1:11
> tc filter add dev $IFACE parent 1:0 protocol ip prio 3 handle 3 fw classid
> 1:12
> tc filter add dev $IFACE parent 1:0 protocol ip prio 4 handle 4 fw classid
> 1:13
> tc filter add dev $IFACE parent 1:0 protocol ip prio 5 handle 5 fw classid
> 1:14
> tc filter add dev $IFACE parent 1:0 protocol ip prio 6 handle 6 fw classid
> 1:15
>
> iptables -t mangle -I PREROUTING -p icmp -j MARK --set-mark 0x1
> iptables -t mangle -I PREROUTING -p icmp -j RETURN
> iptables -t mangle -I PREROUTING -p tcp -m tcp --sport ssh -j
> MARK --set-mark 0x1
> iptables -t mangle -I PREROUTING -p tcp -m tcp --sport ssh -j RETURN
> iptables -t mangle -I PREROUTING -p tcp -m tcp --tcp-flags SYN,RST,ACK
> SYN -j MARK --set-mark 0x1
> iptables -t mangle -I PREROUTING -p tcp -m tcp --tcp-flags SYN,RST,ACK
> SYN -j RETURN
> iptables -t mangle -I PREROUTING -p tcp -m tcp --sport https -j
> MARK --set-mark 0x3
> iptables -t mangle -I PREROUTING -p tcp -m tcp --sport https -j RETURN
>
> iptables -t mangle -I PREROUTING -m tos --tos Minimize-Delay -j
> MARK --set-mark 0x1
> iptables -t mangle -I PREROUTING -m tos --tos Minimize-Delay -j RETURN
> iptables -t mangle -I PREROUTING -m tos --tos Minimize-Cost -j
> MARK --set-mark 0x5
> iptables -t mangle -I PREROUTING -m tos --tos Minimize-Cost -j RETURN
> iptables -t mangle -I PREROUTING -m tos --tos Maximize-Throughput -j
> MARK --set-mark 0x6
> iptables -t mangle -I PREROUTING -m tos --tos Maximize-Throughput -j RETURN
>
> Thanks in advance for any suggestions
I think this is a good script.
But different prio''s for filters are not usefull. They only determine
the
order the filters are matched. And in your case, there is no specific order.
In fact, if you add 1 fw filter with no handle parameter, the mark will be
used as filter key. So packets marked with 16 will end up in class 1:16. I
think this will save more CPU cycles.
Stef
--
stef.coene@docum.org
"Using Linux as bandwidth manager"
http://www.docum.org/
#lartc @ irc.oftc.net
_______________________________________________
LARTC mailing list / LARTC@mailman.ds9a.nl
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/