Hi,
I have tested SOEKRIS4521-50.image on a Soekris NET4511. The boot
sequence failed with this log :
boot>
booting hd0a:/bsd: 53407060+463132 [61+127216+116991]=0x339ba3c
entry point at 0x200120
[ using 244684 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2011 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.0 (SOEKRIS4521) #0: Wed Nov 2 12:07:42 MDT 2011
root at i386.builder:/obj/SOEKRIS4521
cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD" 486-class)
cpu0: FPU
real mem = 66646016 (63MB)
avail mem = 12173312 (11MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/31/19, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc8000/0xa000
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev 0x00: product
0 steppi>
gpio0 at elansc0: 32 pins
cbb0 at pci0 dev 9 function 0 "TI PCI1410 CardBus" rev 0x02: irq 10
sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 11, 8
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 5, a9
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer 0x3f
pcmcia0 at cardslot0
isa0 at mainbus0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
wdc0 at isa0 port 0x1f0/8 irq 14
wd0 at wdc0 channel 0 drive 0: <SanDisk SDCFH-004G>
wd0: 1-sector PIO, LBA48, 3815MB, 7813120 sectors
wd0(wdc0:0:0): using BIOS timings
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
Any suggestion is welcome.
Regards.
?ric Boudrand
Is that everything that happens? No more output? //Johan Den 31 jan 2012 12:36 skrev "Eric Boudrand" <eric.boudrand at caramail.com>:> Hi, > > I have tested SOEKRIS4521-50.image on a Soekris NET4511. The boot > sequence failed with this log : > > boot> > booting hd0a:/bsd: 53407060+463132 [61+127216+116991]=0x339ba3c > entry point at 0x200120 > > [ using 244684 bytes of bsd ELF symbol table ] > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2011 OpenBSD. All rights reserved. > http://www.OpenBSD.org > > OpenBSD 5.0 (SOEKRIS4521) #0: Wed Nov 2 12:07:42 MDT 2011 > > root at i386.builder:/obj/SOEKRIS4521 > cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD" 486-class) > cpu0: FPU > real mem = 66646016 (63MB) > avail mem = 12173312 (11MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 20/31/19, BIOS32 rev. 0 @ 0xf7840 > pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000 > pcibios0: pcibios_get_intr_routing - function not supported > pcibios0: PCI IRQ Routing information unavailable. > pcibios0: PCI bus #1 is the last bus > bios0: ROM list: 0xc8000/0xa000 > cpu0 at mainbus0: (uniprocessor) > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev 0x00: product 0 > steppi> > gpio0 at elansc0: 32 pins > cbb0 at pci0 dev 9 function 0 "TI PCI1410 CardBus" rev 0x02: irq 10 > sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq > 11, 8 > nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1 > sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq > 5, a9 > nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1 > cardslot0 at cbb0 slot 0 flags 0 > cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer 0x3f > pcmcia0 at cardslot0 > isa0 at mainbus0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > com0: console > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard > wdc0 at isa0 port 0x1f0/8 irq 14 > wd0 at wdc0 channel 0 drive 0: <SanDisk SDCFH-004G> > wd0: 1-sector PIO, LBA48, 3815MB, 7813120 sectors > wd0(wdc0:0:0): using BIOS timings > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > > Any suggestion is welcome. > > Regards. > > ?ric Boudrand > > > _______________________________________________ > flashboot mailing list > flashboot at mindrot.org > https://lists.mindrot.org/mailman/listinfo/flashboot >-------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.mindrot.org/pipermail/flashboot/attachments/20120131/4359e340/attachment.html>
Hi,
Exactly. No more than that :(
If I plug a PCMCIA Wireless card, the log is finishing by :
wd0: 1-sector PIO, LBA48, 3815MB, 7813120 sectors
wd0(wdc0:0:0): using BIOS timings
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
wi0 at pcmcia0 function 0 "INTERSIL, HFA384x/IEEE, Version 01.02" port
0xa000/64
wi0: PRISM2.5 ISL3873 (0x800c), Firmware 1.1.0 (primary), 1.4.9 (station), addr3
And nothing more.
I can boot with a Monowall system. Boot up log for Monowall is :
Consoles: internal video/keyboard
BIOS drive C: is disk0
BIOS 639kB/64512kB available memory
FreeBSD/i386 bootstrap loader, Revision 1.1
(root at mb64.neon1.net, Thu Jul 23 20:56:49 CEST 2009)
/kernel text=0x368050 data=0x3d474+0x22ef4 syms=[0x4+0x47050+0x4+0x5acc6]
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.4-RELEASE-p5 #0: Sun Jan 9 22:24:57 CET 2011
root at mb64.neon1.net:/usr/src/sys/i386/compile/M0N0WALL_EMBEDDED
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Enhanced Am486DX4/Am5x86 Write-Back (486-class CPU)
Origin = "AuthenticAMD" Id = 0x494 Stepping = 4
Features=0x1<FPU>
real memory = 67108864 (64 MB)
avail memory = 39530496 (37 MB)
wlan: mac acl policy registered
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
sysctl machdep.i8254_freq=1189161 returns 0
Timecounter "ELAN" frequency 8333333 Hz quality 1000
pcib0: <AMD Elan SC520 host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
cbb0: <TI1410 PCI-CardBus Bridge> mem 0xa0000000-0xa0000fff irq 10 at
device 9.0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem
0xa0001000-0xa000
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
nsphyter0: <DP83815 10/100 media interface> on miibus0
nsphyter0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:00:24:c1:f3:58
sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0xe200-0xe2ff mem
0xa0002000-0xa000
sis1: Silicon Revision: DP83816A
miibus1: <MII bus> on sis1
nsphyter1: <DP83815 10/100 media interface> on miibus1
nsphyter1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: 00:00:24:c1:f3:59
isa0: <ISA bus> on motherboard
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc8000-0xd1fff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
Timecounters tick every 1.000 msec
Elan-mmcr driver: MMCR at 0xc68ef000.
Elan-mmcr Soekris net45xx comBIOS ver. 1.23 20031119 Copyright (C) 2000-2003
Fast IPsec: Initialized Security Association Processing.
IP Filter: v4.1.33 initialized. Default = block all, Logging = enabled
md0: Preloaded image </mfsroot> 16777216 bytes at 0xc086b0e8
ad0: FAILURE - SET_MULTI status=51<READY,DSC,ERROR> error=4<ABORTED>
ad0: 3825MB <SanDisk SDCFH-004G HDX 5.11> at ata0-master PIO4
It seems to be more available memory for FreeBSD system than OpenBSD system (37
MB vs 11 MB).
?ric
Le mardi 31 janvier 2012 ? 17:03 +0100, Johan Ryberg a ?crit
:> Is that everything that happens? No more output?
>
> //Johan
>
> Den 31 jan 2012 12:36 skrev "Eric Boudrand"
> <eric.boudrand at caramail.com>:
> Hi,
>
> I have tested SOEKRIS4521-50.image on a Soekris NET4511. The
> boot
> sequence failed with this log :
>
> boot>
> booting hd0a:/bsd: 53407060+463132 [61+127216
> +116991]=0x339ba3c
> entry point at 0x200120
>
> [ using 244684 bytes of bsd ELF symbol table ]
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All
> rights reserved.
> Copyright (c) 1995-2011 OpenBSD. All rights reserved.
> http://www.OpenBSD.org
>
> OpenBSD 5.0 (SOEKRIS4521) #0: Wed Nov 2 12:07:42 MDT 2011
>
> root at i386.builder:/obj/SOEKRIS4521
> cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD"
> 486-class)
> cpu0: FPU
> real mem = 66646016 (63MB)
> avail mem = 12173312 (11MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 20/31/19, BIOS32 rev. 0
> @ 0xf7840
> pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
> pcibios0: pcibios_get_intr_routing - function not supported
> pcibios0: PCI IRQ Routing information unavailable.
> pcibios0: PCI bus #1 is the last bus
> bios0: ROM list: 0xc8000/0xa000
> cpu0 at mainbus0: (uniprocessor)
> pci0 at mainbus0 bus 0: configuration mode 1 (bios)
> elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev
0x00:
> product 0 steppi>
> gpio0 at elansc0: 32 pins
> cbb0 at pci0 dev 9 function 0 "TI PCI1410 CardBus" rev
0x02:
> irq 10
> sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev
0x00,
> DP83816A: irq 11, 8
> nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
> sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev
0x00,
> DP83816A: irq 5, a9
> nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
> cardslot0 at cbb0 slot 0 flags 0
> cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer
> 0x3f
> pcmcia0 at cardslot0
> isa0 at mainbus0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> com0: console
> com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard
> wdc0 at isa0 port 0x1f0/8 irq 14
> wd0 at wdc0 channel 0 drive 0: <SanDisk SDCFH-004G>
> wd0: 1-sector PIO, LBA48, 3815MB, 7813120 sectors
> wd0(wdc0:0:0): using BIOS timings
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception
> 16
>
> Any suggestion is welcome.
>
> Regards.
>
> ?ric Boudrand
>
>
> _______________________________________________
> flashboot mailing list
> flashboot at mindrot.org
> https://lists.mindrot.org/mailman/listinfo/flashboot
Looks a bit like there''s no getty running on the serial port.. Do you get further if you boot into single-user mode? On 2012/01/31 12:36, Eric Boudrand wrote:> Hi, > > I have tested SOEKRIS4521-50.image on a Soekris NET4511. The boot > sequence failed with this log : > > boot> > booting hd0a:/bsd: 53407060+463132 [61+127216+116991]=0x339ba3c > entry point at 0x200120 > > [ using 244684 bytes of bsd ELF symbol table ] > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2011 OpenBSD. All rights reserved. http://www.OpenBSD.org > > OpenBSD 5.0 (SOEKRIS4521) #0: Wed Nov 2 12:07:42 MDT 2011 > > root at i386.builder:/obj/SOEKRIS4521 > cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD" 486-class) > cpu0: FPU > real mem = 66646016 (63MB) > avail mem = 12173312 (11MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 20/31/19, BIOS32 rev. 0 @ 0xf7840 > pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000 > pcibios0: pcibios_get_intr_routing - function not supported > pcibios0: PCI IRQ Routing information unavailable. > pcibios0: PCI bus #1 is the last bus > bios0: ROM list: 0xc8000/0xa000 > cpu0 at mainbus0: (uniprocessor) > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev 0x00: product 0 steppi> > gpio0 at elansc0: 32 pins > cbb0 at pci0 dev 9 function 0 "TI PCI1410 CardBus" rev 0x02: irq 10 > sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 11, 8 > nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1 > sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 5, a9 > nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1 > cardslot0 at cbb0 slot 0 flags 0 > cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer 0x3f > pcmcia0 at cardslot0 > isa0 at mainbus0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > com0: console > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard > wdc0 at isa0 port 0x1f0/8 irq 14 > wd0 at wdc0 channel 0 drive 0: <SanDisk SDCFH-004G> > wd0: 1-sector PIO, LBA48, 3815MB, 7813120 sectors > wd0(wdc0:0:0): using BIOS timings > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > > Any suggestion is welcome. > > Regards. > > ?ric Boudrand > > > _______________________________________________ > flashboot mailing list > flashboot at mindrot.org > https://lists.mindrot.org/mailman/listinfo/flashboot
Hi, Le mardi 31 janvier 2012 ? 17:15 +0000, Stuart Henderson a ?crit :> Looks a bit like there''s no getty running on the serial port.. > Do you get further if you boot into single-user mode?Same result with boot -s ?ric
Hi,> Have you tried with 4.9, I believe the memory disk size changed > drastically in 5.0 bringing it to around 48 MB, it was much smaller in > 4.9 which may give you enough room to boot. >No. Only 5.0. I have to build a 4.9 system then. Or I will try to download older binary releases. ?ric