Abdullah Al-Marrie
2006-Dec-20 12:10 UTC
Acer Aspire 5102 WLMi with Turion 64 X2 dual-core TL-50 1.6 GHz on FreeBSD 6.2 ACPI problems
Hello guys,
I have problem with my new laptop Acer Aspire 5102 WLMi which has AMD
Turion? 64 X2 dual-core TL-50 1.6 GHz with 1.5 GB of ram.
I'm running i386 6.2-RC1 upgraded to 6.2-PRELEASE via RELENG6 tag
since I don't have more than 4 GB of ram.
1. The FreeBSD can't detect the builtin wlan chip which is Broadcom
BCM 4318 Rev 2.
OpenSuse 10.2 detected my my builtin wlan
<4>ieee80211: module not supported by Novell, setting U taint flag.
<6>bcm43xx: Chip ID 0x4318, rev 0x2
<6>bcm43xx: Number of cores: 4
<6>bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled
<6>bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, disabled
<6>bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled
<6>bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled
<6>bcm43xx: PHY connected
<6>bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7
<6>bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev: 8)
Here is very interesting thread about the Acer laptops only.
http://www.ubuntuforums.org/showthread.php?t=280962
## ******************** ONLY FOR ACER USERS ********************
#install acer_acpi to turn on wireless adapter through software
#this is the only package that will be manually installed
#as it will be compiled, it works on 32-bit and 64-bit systems whereas acerhk
#only works on 32-bit systems AFAIK
#when upgrading kernel, make sure to re-compile/re-install acer_acpi in the new
kernel
wget http://www.archernar.co.uk/acer_acpi/acer_acpi-0.3.tar.gz
tar -xvf acer_acpi-0.3.tar.gz
cd acer_acpi-0.3
sudo apt-get install build-essential linux-kernel-headers linux-headers-$arch
linux-headers-?uname -r?
make
sudo make install
echo 'acer_acpi' | sudo tee -a /etc/modules
echo 'pre-up /etc/network/StartAcerWireless' | sudo tee -a
/etc/network/interfaces
sudo touch /etc/network/StartAcerWireless
echo 'chmod 777 /proc/acpi/acer/wireless' | sudo tee -a
/etc/network/StartAcerWireless
echo 'echo "enabled: 1" > /proc/acpi/acer/wireless' | sudo
tee -a
/etc/network/StartAcerWireless
echo 'iwconfig eth1 ap any' | sudo tee -a /etc/network/StartAcerWireless
sudo chmod 754 /etc/network/StartAcerWireless
## ************************************************** ***********
Start GDM and from the menu, go to System|Preferences|Sessions|Startup
Programs, click the Add button and write in:
nm-applet ?sm-disable
reboot PC
When rebooted, left-click on nm-applet and choose to "connect to other
wireless network" even if your AP is visible. Write in the SSID, choose WEP
or WPA and enter the password. Upon connecting nm-applet will ask for a master
password for the wallet. Choose something simple.
----
In FreeBSD 6.2-PRERELEASE
The bluetooth it works when I use the button to turn it on.
Dec 20 22:13:35 kernel: ugen1: Broadcom Corp Acer Module, rev 2.00/1.00, addr 2
But nothing appears when I switch the wlan button off/on.
Wlan light is working on the FreeBSD but it doesn't appear in the
dmesg or /var/log/messages
2. powerd in rc.conf causes the laptop to hangs too.
# sysctl dev.cpu
dev.cpu.0.%desc: ACPI CPU
dev.cpu.0.%driver: cpu
dev.cpu.0.%location: handle=\_PR_.CPU0
dev.cpu.0.%pnpinfo: _HID=none _UID=0
dev.cpu.0.%parent: acpi0
dev.cpu.0.freq: 1592
dev.cpu.0.freq_levels: 1592/70000 796/19383
dev.cpu.1.%desc: ACPI CPU
dev.cpu.1.%driver: cpu
dev.cpu.1.%location: handle=\_PR_.CPU1
dev.cpu.1.%pnpinfo: _HID=none _UID=0
dev.cpu.1.%parent: acpi0
# sysctl dev.powernow
dev.powernow.0.%desc: PowerNow! K8
dev.powernow.0.%driver: powernow
dev.powernow.0.%parent: cpu0
dev.powernow.0.freq_settings: 1592/70000 796/19383
dev.powernow.1.%desc: PowerNow! K8
dev.powernow.1.%driver: powernow
dev.powernow.1.%parent: cpu1
dev.powernow.1.freq_settings: 1592/70000 796/19383
# sysctl dev.acpi_throttle
sysctl: unknown oid 'dev.acpi_throttle'
3. Sound hardware isn't detected at all.
pciconf -lv | grep -B 4 audio returns with no output.
4. system wont reboot or shutdown, it hangs after sync disks, I have
to press thr button power to switch it off.
---
Booting with ACPI disabled causes crash all the time.
cbb0:
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pci6: <memory, flash> at device 4.1 (no driver attached)
pci6: <base peripheral> at device 4.2 (no driver attached)
pci6: <memory, flash> at device 4.3 (no driver attached)
pci6: <memory, flash> at device 4.4 (no driver attached)
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
Fatal trap 9: general protection fault while in kernel mode
cpuid = 0; apic id = 00
instruction pointer = 0x70 :0x10000
stack pointer = 0x28 :0xfd0
frame pointer = 0x28 :0xcc5
code segment = base 0xc000e4c5, limit 0xffff, type 0x1b
= DPL 0, press 1, def32 0, gran 0
processor eflags = interrupt enabled, reusme, IOPL = 0
current processes = 0 (swapper)
trap number = 9
panic: general protection fault
cpuid = 0
uptime: 1s
dmesg -v output:
FreeBSD 6.2-PRERELEASE FreeBSD 6.2-PRERELEASE #0: Wed Dec 20 21:05:03
AST 2006 arabian@:/usr/obj/usr/src/sys/ARABIAN i386
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-PRERELEASE #0: Wed Dec 20 21:05:03 AST 2006
arabian@:/usr/obj/usr/src/sys/ARABIAN
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a77000.
Preloaded elf module "/boot/kernel/linux.ko" at 0xc0a771c4.
Preloaded elf module "/boot/kernel/wlan_acl.ko" at 0xc0a77270.
Preloaded elf module "/boot/modules/bcmwl5_sys.ko" at 0xc0a77320.
Preloaded elf module "/boot/kernel/if_ndis.ko" at 0xc0a773d0.
Preloaded elf module "/boot/kernel/ndis.ko" at 0xc0a7747c.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a77528.
MP Configuration Table version 1.4 found at 0xc009e171
Table 'FACP' at 0x57e99c04
Table 'SLIC' at 0x57e99c78
Table 'SSDT' at 0x57e99dee
Table 'APIC' at 0x57e99f70
MADT: Found table at 0x57e99f70
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 1: enabled
SMP: Added CPU 1 (AP)
INTR: Adding local APIC 0 as a target
ACPI APIC Table: <PTLTD APIC >
Calibrating clock(s) ... i8254 clock: 1193209 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1596014793 Hz
CPU: AMD Turion(tm) 64 X2 Mobile Technology TL-50 (1596.01-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x40f82 Stepping = 2
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x2001<SSE3,CX16>
AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow+,3DNow>
AMD Features2=0x1f<LAHF,CMP,<b2>,<b3>,CR8>
HTT bit cleared - FreeBSD does not have licensing issues requiring it.
Cores per package: 2
Data TLB: 32 entries, fully associative
Instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 internal cache: 256 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative
real memory = 1474887680 (1406 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009cfff, 638976 bytes (156 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c28000 - 0x000000005658afff, 1435906048 bytes (350563 pages)
avail memory = 1435623424 (1369 MB)
INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
bios32: Found BIOS32 Service Directory header at 0xc00f80c0
bios32: Entry = 0xfd954 (c00fd954) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xfd950+0x0
pnpbios: Found PnP BIOS data at 0xc00f8120
pnpbios: Entry = e4c5:a1f8 Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: high
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0: intpin 9 polarity: low
ioapic0: intpin 9 trigger: level
ioapic0 <Version 2.1> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
wlan: <802.11 Link Layer>
wlan: <802.11 MAC ACL support>
wlan: mac acl policy registered
nfslock: pseudo-device
random: <entropy source, Software, Yarrow>
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
VESA: information block
56 45 53 41 00 02 00 01 00 01 01 00 00 00 22 00
00 01 00 01 00 01 1e 01 00 01 34 01 00 01 39 01
00 01 82 01 0d 01 0e 01 0f 01 20 01 92 01 93 01
94 01 95 01 96 01 a2 01 a3 01 a4 01 a5 01 a6 01
VESA: 60 mode(s) found
VESA: v2.0, 16384k memory, flags:0x1, mode table:0xc08c55e2 (1000022)
VESA: ATI RADEON XPRESS 200M Series
VESA: ATI Technologies Inc. MS48 01.00
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
npx0: INT 16 interface
acpi0: <ACRSYS RSDT> on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80012814
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=59501002)
pcibios: BIOS_PRESENT call failed
AcpiOsDerivePciId: bus 0 dev 18 func 0
AcpiOsDerivePciId: bus 0 dev 17 func 0
AcpiOsDerivePciId: bus 0 dev 20 func 1
AcpiOsDerivePciId: bus 0 dev 20 func 3
AcpiOsDerivePciId: bus 6 dev 2 func 0
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xd93ea000 pa 0x9c000
AcpiOsDerivePciId: bus 0 dev 0 func 0
ACPI timer: 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x10> port 0x62,0x66 on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 10 11
Validation 0 255 N 0 10 11
After Disable 0 255 N 0 10 11
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 10 11
Validation 0 255 N 0 10 11
After Disable 0 255 N 0 10 11
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 10 11
Validation 0 255 N 0 10 11
After Disable 0 255 N 0 10 11
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 10 11
Validation 0 255 N 0 10 11
After Disable 0 255 N 0 10 11
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 10 11
Validation 0 255 N 0 10 11
After Disable 0 255 N 0 10 11
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 10 11
Validation 0 255 N 0 10 11
After Disable 0 255 N 0 10 11
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 10 11
Validation 0 255 N 0 10 11
After Disable 0 255 N 0 10 11
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 10 11
Validation 0 255 N 0 10 11
After Disable 0 255 N 0 10 11
pci_link8: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7
Validation 0 255 N 0 3 4 5 7
After Disable 0 255 N 0 3 4 5 7
cpu0: <ACPI CPU> on acpi0
powernow0: <PowerNow! K8> on cpu0
cpu1: <ACPI CPU> on acpi0
powernow1: <PowerNow! K8> on cpu1
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1002, dev=0x5950, revid=0x10
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2220, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1002, dev=0x5a3f, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1002, dev=0x5a36, revid=0x00
bus=0, slot=4, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0000, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
powerspec 3 supports D0 D3 current D0
MSI supports 1 message
found-> vendor=0x1002, dev=0x5a37, revid=0x00
bus=0, slot=5, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0000, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
powerspec 3 supports D0 D3 current D0
MSI supports 1 message
found-> vendor=0x1002, dev=0x4374, revid=0x80
bus=0, slot=19, func=0
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0017, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
MSI supports 1 message
map[10]: type 1, range 32, base c0004000, size 12, enabled
pcib0: matched entry for 0.19.INTA
pcib0: slot 19 INTA hardwired to IRQ 19
found-> vendor=0x1002, dev=0x4375, revid=0x80
bus=0, slot=19, func=1
class=0c-03-10, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
MSI supports 1 message
map[10]: type 1, range 32, base c0005000, size 12, enabled
pcib0: matched entry for 0.19.INTA
pcib0: slot 19 INTA hardwired to IRQ 19
found-> vendor=0x1002, dev=0x4373, revid=0x80
bus=0, slot=19, func=2
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
MSI supports 1 message
map[10]: type 1, range 32, base c0006000, size 12, enabled
pcib0: matched entry for 0.19.INTA
pcib0: slot 19 INTA hardwired to IRQ 19
found-> vendor=0x1002, dev=0x4372, revid=0x83
bus=0, slot=20, func=0
class=0c-05-00, hdrtype=0x00, mfdev=1
cmdreg=0x0003, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 00008400, size 4, enabled
map[14]: type 1, range 32, base fed00000, size 10, enabled
found-> vendor=0x1002, dev=0x4376, revid=0x80
bus=0, slot=20, func=1
class=01-01-82, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
MSI supports 1 message
map[20]: type 4, range 32, base 00008410, size 4, enabled
pcib0: matched entry for 0.20.INTA
pcib0: slot 20 INTA hardwired to IRQ 16
found-> vendor=0x1002, dev=0x437b, revid=0x01
bus=0, slot=20, func=2
class=04-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0410, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 64, base c0000000, size 14, enabled
pcib0: matched entry for 0.20.INTA
pcib0: slot 20 INTA hardwired to IRQ 16
found-> vendor=0x1002, dev=0x4377, revid=0x80
bus=0, slot=20, func=3
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1002, dev=0x4371, revid=0x80
bus=0, slot=20, func=4
class=06-04-01, hdrtype=0x01, mfdev=1
cmdreg=0x0007, statreg=0x02a0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1100, revid=0x00
bus=0, slot=24, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1101, revid=0x00
bus=0, slot=24, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1102, revid=0x00
bus=0, slot=24, func=2
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1103, revid=0x00
bus=0, slot=24, func=3
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0x9000-0x9fff
pcib1: memory decode 0xc0100000-0xc01fffff
pcib1: prefetched decode 0xc8000000-0xcfffffff
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x1002, dev=0x5975, revid=0x00
bus=1, slot=5, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 3, range 32, base c8000000, size 27, enabled
pcib1: requested memory range 0xc8000000-0xcfffffff: good
map[14]: type 4, range 32, base 00009000, size 8, enabled
pcib1: requested I/O range 0x9000-0x90ff: in range
map[18]: type 1, range 32, base c0100000, size 16, enabled
pcib1: requested memory range 0xc0100000-0xc010ffff: good
pcib1: matched entry for 1.5.INTA
pcib1: slot 5 INTA hardwired to IRQ 17
pci1: <display, VGA> at device 5.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 3
pcib2: I/O decode 0x0-0x0
pcib2: memory decode 0x0-0x0
pcib2: prefetched decode 0x0-0x0
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
pcib3: <ACPI PCI-PCI bridge> at device 5.0 on pci0
pcib3: secondary bus 4
pcib3: subordinate bus 5
pcib3: I/O decode 0x0-0x0
pcib3: memory decode 0x0-0x0
pcib3: prefetched decode 0x0-0x0
pci4: <ACPI PCI bus> on pcib3
pci4: physical bus=4
ohci0: <ATI SB400 USB Controller> mem 0xc0004000-0xc0004fff irq 19 at
device 19.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xc0004000
ioapic0: routing intpin 19 (PCI IRQ 19) to vector 49
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <ATI SB400 USB Controller> on ohci0
usb0: USB revision 1.0
uhub0: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ohci1: <ATI SB400 USB Controller> mem 0xc0005000-0xc0005fff irq 19 at
device 19.1 on pci0
ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xc0005000
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: <ATI SB400 USB Controller> on ohci1
usb1: USB revision 1.0
uhub1: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
ehci0: <ATI SB400 USB 2.0 controller> mem 0xc0006000-0xc0006fff irq 19
at device 19.2 on pci0
ehci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xc0006000
ehci0: [GIANT-LOCKED]
ehci0: Dropped interrupts workaround enabled
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <ATI SB400 USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 8 ports with 8 removable, self powered
ugen0: vendor 0x0402 USB2.0 Camera, rev 2.00/1.00, addr 2
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci0: <ATI IXP400 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x8410-0x841f irq 16 at device
20.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x8410
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0: reset tp2 stat0=50 stat1=00 devices=0x9<ATAPI_SLAVE,ATA_MASTER>
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 50
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 51
ata1: [MPSAFE]
pci0: <multimedia> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib4: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pcib4: secondary bus 6
pcib4: subordinate bus 8
pcib4: I/O decode 0xa000-0xafff
pcib4: memory decode 0xc0200000-0xc02fffff
pcib4: prefetched decode 0xfff00000-0xfffff
pcib4: Subtractively decoded bridge.
pci6: <ACPI PCI bus> on pcib4
pci6: physical bus=6
found-> vendor=0x10ec, dev=0x8139, revid=0x10
bus=6, slot=1, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=4
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000a000, size 8, enabled
pcib4: requested I/O range 0xa000-0xa0ff: in range
map[14]: type 1, range 32, base c0202000, size 8, enabled
pcib4: requested memory range 0xc0202000-0xc02020ff: good
pcib4: matched entry for 6.1.INTA
pcib4: slot 1 INTA hardwired to IRQ 21
found-> vendor=0x14e4, dev=0x4318, revid=0x02
bus=6, slot=2, func=0
class=02-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[10]: type 1, range 32, base c0200000, size 13, enabled
pcib4: requested memory range 0xc0200000-0xc0201fff: good
pcib4: matched entry for 6.2.INTA
pcib4: slot 2 INTA hardwired to IRQ 22
found-> vendor=0x1524, dev=0x1412, revid=0x10
bus=6, slot=4, func=0
class=06-07-00, hdrtype=0x02, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x44 (17000 ns), maxlat=0x07 (1750 ns)
intpin=a, irq=11
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base c0203000, size 12, enabled
pcib4: requested memory range 0xc0203000-0xc0203fff: good
pcib4: matched entry for 6.4.INTA
pcib4: slot 4 INTA hardwired to IRQ 20
found-> vendor=0x1524, dev=0x0530, revid=0x01
bus=6, slot=4, func=1
class=05-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x01 (250 ns), maxlat=0x04 (1000 ns)
intpin=b, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base c0202400, size 7, enabled
pcib4: requested memory range 0xc0202400-0xc020247f: good
pcib4: matched entry for 6.4.INTB
pcib4: slot 4 INTB hardwired to IRQ 23
found-> vendor=0x1524, dev=0x0550, revid=0x01
bus=6, slot=4, func=2
class=08-05-01, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x20 (8000 ns), maxlat=0x48 (18000 ns)
intpin=b, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base c0202800, size 8, enabled
pcib4: requested memory range 0xc0202800-0xc02028ff: good
pcib4: matched entry for 6.4.INTB
pcib4: slot 4 INTB hardwired to IRQ 23
found-> vendor=0x1524, dev=0x0520, revid=0x01
bus=6, slot=4, func=3
class=05-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x01 (250 ns), maxlat=0x04 (1000 ns)
intpin=b, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base c0202c00, size 7, enabled
pcib4: requested memory range 0xc0202c00-0xc0202c7f: good
pcib4: matched entry for 6.4.INTB
pcib4: slot 4 INTB hardwired to IRQ 23
found-> vendor=0x1524, dev=0x0551, revid=0x01
bus=6, slot=4, func=4
class=05-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x20 (8000 ns), maxlat=0x48 (18000 ns)
intpin=b, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base 00000000, size 8, memory disabled
rl0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xa000
pcib4: rl0 requested I/O range 0xa000-0xa0ff: in range
rl0: <RealTek 8139 10/100BaseTX> port 0xa000-0xa0ff mem
0xc0202000-0xc02020ff irq 21 at device 1.0 on pci6
pcib4: rl0 requested I/O range 0xa000-0xa0ff: in range
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: bpf attached
rl0: Ethernet address: 00:16:d4:1c:30:be
ioapic0: routing intpin 21 (PCI IRQ 21) to vector 52
rl0: [MPSAFE]
pci6: <network> at device 2.0 (no driver attached)
cbb0: <PCI-CardBus Bridge> mem 0xc0203000-0xc0203fff irq 20 at device
4.0 on pci6
cbb0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xc0203000
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
ioapic0: routing intpin 20 (PCI IRQ 20) to vector 53
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
0x00: 0x14121524 0x02100007 0x06070010 0x00824008
0x10: 0xc0203000 0x020000a0 0x20070706 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc
0x30: 0x00000000 0xfffffffc 0x00000000 0x07440114
0x40: 0x009f1025 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x4060d021 0x00000000 0x00000000 0x90501212
0x90: 0x604402c0 0x00000000 0x00000000 0x00000000
0xa0: 0xfe010001 0x00c00000 0x00000013 0x0000000d
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00001003 0x00800080 0x10080400 0x000007fe
0xd0: 0x00e00000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pci6: <memory, flash> at device 4.1 (no driver attached)
pci6: <base peripheral> at device 4.2 (no driver attached)
pci6: <memory, flash> at device 4.3 (no driver attached)
pci6: <memory, flash> at device 4.4 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
kbd0: atkbd0, generic (0), config:0x0, flags:0x3f0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 54
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
ioapic0: routing intpin 12 (ISA IRQ 12) to vector 55
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
battery0: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ahc_isa_probe 0: ioport 0xc00 alloc failed
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0x1 0x1 0x1 0x1
sio0: probe failed test(s): 0 1 2 4 6 7 9
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
ioapic0: routing intpin 4 (ISA IRQ 4) to vector 56
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x1 0x1 0x1 0x1
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 99750517 hz
Timecounter "TSC" frequency 1596014793 Hz quality -100
Timecounters tick every 1.000 msec
Linux ELF exec handler installed
lo0: bpf attached
battery0: battery initialization start
acpi_acad0: acline initialization start
pcib4: cardbus0 requested memory range 0xc0200000-0xc02fffff: good
pcib4: cardbus0 requested memory range 0xc0200000-0xc02fffff: good
pcib4: cardbus0 requested memory range 0xc0204000-0xc0205fff: good
found-> vendor=0x14e4, dev=0x4320, revid=0x03
bus=7, slot=0, func=0
class=02-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0xa8 (5040 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=20
powerspec 2 supports D0 D1 D2 D3 current D0
ndis0: <Wireless-G Notebook Adapter> mem 0xc0204000-0xc0205fff irq 20
at device 0.0 on cardbus0
ndis0: Reserved 0x2000 bytes for rid 0x10 type 3 at 0xc0204000
ndis0: Reserved 0x1 bytes for rid 0 type 1 at 0x14
ndis0: [MPSAFE]
ndis0: NDIS API version: 5.0
ata0-slave: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad0: setting PIO4 on IXP400 chip
ad0: setting UDMA100 on IXP400 chip
ad0: 76319MB <HTS541080G9AT00 MB4OA60A> at ata0-master UDMA100
ad0: 156301488 sectors [155061C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad0
acpi_tz0: _AC0: temperature 55.0 >= setpoint 50.0
acpi_tz0: switched from NONE to _AC0: 55.0C
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
battery0: battery initialization done, tried 1 times
acd0: setting PIO4 on IXP400 chip
ndis0: bpf attached
ndis0: Ethernet address: 00:12:17:bc:4f:87
ndis0: bpf attached
acd0: setting UDMA33 on IXP400 chip
acd0: <Slimtype DVDRW SSM-8515S/GRS6> DVDR drive at ata0 as slave
acd0: read 4134KB/s (4134KB/s) write 4134KB/s (4134KB/s), 2048KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-R 120mm photo disc
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
ioapic0: Assigning ISA IRQ 1 to local APIC 0
ioapic0: Assigning ISA IRQ 4 to local APIC 1
ioapic0: Assigning ISA IRQ 9 to local APIC 0
ioapic0: Assigning ISA IRQ 12 to local APIC 1
ioapic0: Assigning ISA IRQ 14 to local APIC 0
ioapic0: Assigning ISA IRQ 15 to local APIC 1
ioapic0: Assigning PCI IRQ 19 to local APIC 0
ioapic0: Assigning PCI IRQ 20 to local APIC 1
ioapic0: Assigning PCI IRQ 21 to local APIC 0
Trying to mount root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
module_register: module pci/radeon already exists!
Module pci/radeon failed to register: 17
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
acpi_tz0: switched from _AC0 to NONE: 49.0C
acpi_tz0: _AC0: temperature 50.0 >= setpoint 50.0
acpi_tz0: switched from NONE to _AC0: 50.0C
acpi_tz0: switched from _AC0 to NONE: 49.0C
acpi_tz0: _AC0: temperature 50.0 >= setpoint 50.0
acpi_tz0: switched from NONE to _AC0: 50.0C
acpi_tz0: switched from _AC0 to NONE: 49.0C
acpi_tz0: _AC0: temperature 50.0 >= setpoint 50.0
acpi_tz0: switched from NONE to _AC0: 50.0C
ugen1: Broadcom Corp Acer Module, rev 2.00/1.00, addr 2
PS: the ndis you see here is for WPC54G PCMICA I use since the
broadcom isn't detected at al.
# sysctl hw.acpi
hw.acpi.supported_sleep_state: S3 S4 S5
hw.acpi.power_button_state: S5
hw.acpi.sleep_button_state: S3
hw.acpi.lid_switch_state: NONE
hw.acpi.standby_state: S1
hw.acpi.suspend_state: S3
hw.acpi.sleep_delay: 1
hw.acpi.s4bios: 0
hw.acpi.verbose: 1
hw.acpi.disable_on_reboot: 0
hw.acpi.handle_reboot: 0
hw.acpi.reset_video: 0
hw.acpi.cpu.cx_supported: C1/0
hw.acpi.cpu.cx_lowest: C1
hw.acpi.cpu.cx_usage: 100.00%
hw.acpi.thermal.min_runtime: 0
hw.acpi.thermal.polling_rate: 10
hw.acpi.thermal.user_override: 0
hw.acpi.thermal.tz0.temperature: 51.0C
hw.acpi.thermal.tz0.active: 0
hw.acpi.thermal.tz0.passive_cooling: 1
hw.acpi.thermal.tz0.thermal_flags: 0
hw.acpi.thermal.tz0._PSV: 78.0C
hw.acpi.thermal.tz0._HOT: -1
hw.acpi.thermal.tz0._CRT: 95.0C
hw.acpi.thermal.tz0._ACx: 50.0C -1 -1 -1 -1 -1 -1 -1 -1 -1
hw.acpi.battery.life: 100
hw.acpi.battery.time: -1
hw.acpi.battery.state: 0
hw.acpi.battery.units: 1
hw.acpi.battery.info_expire: 5
hw.acpi.acline: 1
----
# iasl Acer-Aspire-5102-WLMi.asl
Intel ACPI Component Architecture
ASL Optimizing Compiler / AML Disassembler version 20041119 [Dec 20 2006]
Copyright (C) 2000 - 2004 Intel Corporation
Supports ACPI Specification Revision 2.0c
Acer-Aspire-5102-WLMi.asl 212: Method (_WAK, 1, NotSerialized)
Warning 2026 - ^ Reserved method must
return a value (_WAK)
Acer-Aspire-5102-WLMi.asl 788: Method (Z00B, 0, NotSerialized)
Warning 2019 - Not all control paths return a value ^ (Z00B)
Acer-Aspire-5102-WLMi.asl 1283: Name (_WDG, Buffer (0xDC)
Warning 2033 - Unknown reserved name ^ (_WDG)
Acer-Aspire-5102-WLMi.asl 1346: Method (_WED, 1, NotSerialized)
Warning 2019 - Not all control paths return a value ^ (_WED)
Acer-Aspire-5102-WLMi.asl 1346: Method (_WED, 1, NotSerialized)
Warning 2033 - Unknown reserved name ^ (_WED)
Acer-Aspire-5102-WLMi.asl 1352: Return (Z00B ())
Warning 2030 - Called method may not always return a value ^
Acer-Aspire-5102-WLMi.asl 1389: Method (WMBD, 3, NotSerialized)
Warning 2019 - Not all control paths return a value ^ (WMBD)
ASL Input: Acer-Aspire-5102-WLMi.asl - 7886 lines, 277442 bytes, 3468 keywords
AML Output: DSDT.aml - 31300 bytes 918 named objects 2550 executable opcodes
Compilation complete. 0 Errors, 7 Warnings, 0 Remarks, 1038 Optimizations
-----
The Acer-Aspire-5102-WLMi.asl can be downloaded from
http://www.wearab.net/acpi/Acer-Aspire-5102-WLMi.asl
DSDT.aml can be downloaded from http://www.wearab.net/acpi/DSDT.aml
I know you are too busy guys, and I appreciate your great efforts to
make FreeBSD better.
I remain thanking you,
-Abdullah Ibn Hamad Al-Marri
Arab Portal
http://www.WeArab.Net/
Scot Hetzel
2006-Dec-21 05:15 UTC
Acer Aspire 5102 WLMi with Turion 64 X2 dual-core TL-50 1.6 GHz on FreeBSD 6.2 ACPI problems
On 12/20/06, Abdullah Al-Marrie <almarrie@gmail.com> wrote:> Hello guys, > > I have problem with my new laptop Acer Aspire 5102 WLMi which has AMD > Turion? 64 X2 dual-core TL-50 1.6 GHz with 1.5 GB of ram. > > I'm running i386 6.2-RC1 upgraded to 6.2-PRELEASE via RELENG6 tag > since I don't have more than 4 GB of ram. > > 1. The FreeBSD can't detect the builtin wlan chip which is Broadcom > BCM 4318 Rev 2. >You need to use the Windows NDIS driver to use the Broadcom Wireless adapter. You just need to download the driver from Acer's web site, and then use ndisgen to build the kernel module. Scot -- DISCLAIMER: No electrons were mamed while sending this message. Only slightly bruised.
Patrick Bowen
2006-Dec-21 06:19 UTC
Acer Aspire 5102 WLMi with Turion 64 X2 dual-core TL-50 1.6 GHz on FreeBSD 6.2 ACPI problems
Abdullah Al-Marrie wrote: [snip]...> > 1. The FreeBSD can't detect the builtin wlan chip which is Broadcom > BCM 4318 Rev 2.[snip]... Have you tried using ndisgen(8) and the Windows bcmwl5.[sys,inf] files to create the module bcmwl5_sys.ko? I have a Gateway with the Broadcom 4318, and that routine worked for me. You may have to try different .sys and .inf files (i.e. Broadcom, Dell, etc) to get it to work. If it does, then when you kldload(8) the module, you'll see something like this in dmesg(8); ndis0: <Dell TrueMobile 1300 WLAN Mini-PCI Card> mem 0xb8004000-0xb8005fff irq 17 at device 4.0 on pci6 ndis0: NDIS API version: 5.1 ndis0: Ethernet address: 00:14:a5:80:f5:c9 Good luck, Patrick