I have 6.1-RELEASE installed on a Supermicro SuperServer 6014P-TR
with Supermicro motherboard: Super X6DHP-TG
http://supermicro.com/products/motherboard/Xeon800/E7520/X6DHP-TG.cfm
I have four SATA drives attached to the internal backplane which uses
the following controller, I am Not using the onboard RAID features:
Marvell 88SX6081 4-port SATA Controller with 3rd-Party Adaptec
AIC-8110(4x drive), RAID 0, 1, JBOD support
The problem I am seeing occurs with the fourth drive, ad10, and appears
on all read/write operations:
ad10: WARNING - WRITE_DMA48 soft error (ECC corrected) LBA=293046767
kernel:ad10: WARNING - WRITE_DMA soft error (ECC corrected) LBA=12393823
kernel:ad10: WARNING - READ_DMA soft error (ECC corrected) LBA=12480567
This same warning message appears on 6.0-RELEASE and 6.1-STABLE
I have tried swapping drives around, and tried fewer than four drives to
see if I could tie the warning message to either a specific drive or the
number of drives attached to the controller but the message only appears
for the fourth drive port. Beyond the warning message the drive seems to
read and write data correctly.
Currently ad8 and ad10 are joined as providers in a gmirror
configuration, both drives seem to behave fine, but rebuilding the
mirror makes ad10 go crazy with it's ECC warning messages. Gmirror does
not degrade status of the array or anything else related to the
warnings. Also the warning shows up in dmesg before gmirror providers
are initialized, and before I initially setup gmirror on the system.
Hardware issue with the port? Or a controller-driver issue perhaps? How
dangerous is a soft error? Any help on tracking down the cause,
implications, or a solution would be greatly appreciated, as it stands I
am a little nervous trusting this system under any kind of load. I have
attached a verbose dmesg output.
I posted this to the GEOM list but later realized it might be
appropriate for -STABLE since I see a few other -RELEASE related posts
here, at any rate sorry for the cross posting.
Thank You
wadleigh
-------------- next part --------------
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: high
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
ioapic2 <Version 2.0> irqs 48-71 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00000200 err: 0x00010000 pcm: 0x00010000
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
nfslock: pseudo-device
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
npx0: INT 16 interface
acpi0: <PTLTD RSDT> on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000058
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=35908086)
pcibios: BIOS version 2.10
Found $PIR table, 18 entries at 0xc00fdea0
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 1 A 0x60 3 4 5 6 7 9 10 11 12
embedded 0 2 A 0x60 3 4 5 6 7 9 10 11 12
slot 2 2 1 A 0x60 3 4 5 6 7 9 10 11 12
slot 2 2 1 B 0x61 3 4 5 6 7 9 10 11 12
slot 2 2 1 C 0x60 3 4 5 6 7 9 10 11 12
slot 2 2 1 D 0x61 3 4 5 6 7 9 10 11 12
slot 5 2 2 A 0x60 3 4 5 6 7 9 10 11 12
slot 5 2 2 B 0x61 3 4 5 6 7 9 10 11 12
slot 1 3 1 A 0x60 3 4 5 6 7 9 10 11 12
slot 1 3 1 B 0x61 3 4 5 6 7 9 10 11 12
slot 1 3 1 C 0x62 3 4 5 6 7 9 10 11 12
slot 1 3 1 D 0x63 3 4 5 6 7 9 10 11 12
slot 6 3 2 A 0x62 3 4 5 6 7 9 10 11 12
slot 6 3 2 B 0x63 3 4 5 6 7 9 10 11 12
embedded 0 4 A 0x60 3 4 5 6 7 9 10 11 12
slot 4 4 0 A 0x60 3 4 5 6 7 9 10 11 12
slot 4 4 0 B 0x61 3 4 5 6 7 9 10 11 12
slot 4 4 0 C 0x62 3 4 5 6 7 9 10 11 12
slot 4 4 0 D 0x63 3 4 5 6 7 9 10 11 12
embedded 0 6 A 0x60 3 4 5 6 7 9 10 11 12
slot 3 5 0 A 0x60 3 4 5 6 7 9 10 11 12
slot 3 5 0 B 0x61 3 4 5 6 7 9 10 11 12
slot 3 5 0 C 0x62 3 4 5 6 7 9 10 11 12
slot 3 5 0 D 0x63 3 4 5 6 7 9 10 11 12
embedded 6 1 A 0x61 3 4 5 6 7 9 10 11 12
embedded 6 2 A 0x60 3 4 5 6 7 9 10 11 12
embedded 6 2 B 0x61 3 4 5 6 7 9 10 11 12
embedded 0 31 A 0x62 3 4 5 6 7 9 10 11 12
embedded 0 31 B 0x61 3 4 5 6 7 9 10 11 12
embedded 0 29 A 0x60 3 4 5 6 7 9 10 11 12
embedded 0 29 B 0x63 3 4 5 6 7 9 10 11 12
embedded 0 29 C 0x62 3 4 5 6 7 9 10 11 12
embedded 0 29 D 0x6b 3 4 5 6 7 9 10 11 12
Setting up PCIe mappings for BAR 0xe0000000
AcpiOsDerivePciId: bus 0 dev 31 func 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
AcpiOsDerivePciId: bus 0 dev 0 func 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 3 4 5 6 7 10 11 14 15
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 5 N 0 3 4 5 6 7 10 11 14 15
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 5 6 7 10 11 14 15
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 5 6 7 10 11 14 15
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 7 N 0 3 4 5 6 7 10 11 14 15
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 7 N 0 3 4 5 6 7 10 11 14 15
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 10 11 14 15
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 10 11 14 15
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link4: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link4: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link4: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link5: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 4 5 6 7 10 11 14 15
pci_link5: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 4 5 6 7 10 11 14 15
pci_link5: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 4 5 6 7 10 11 14 15
pci_link6: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link6: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link6: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link7: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 4 5 6 7 10 11 14 15
pci_link7: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 10 N 0 4 5 6 7 10 11 14 15
pci_link7: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 4 5 6 7 10 11 14 15
ACPI timer: 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x3590, revid=0x0c
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0106, statreg=0x0090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x3591, revid=0x0c
bus=0, slot=0, func=1
class=ff-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0100, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x3594, revid=0x0c
bus=0, slot=1, func=0
class=08-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0102, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
MSI supports 2 messages
map[10]: type 1, range 32, base dd000000, size 12, enabled
pcib0: matched entry for 0.1.INTA
pcib0: slot 1 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x3595, revid=0x0c
bus=0, slot=2, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
pcib0: matched entry for 0.2.INTA
pcib0: slot 2 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x3597, revid=0x0c
bus=0, slot=4, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x4018, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
pcib0: matched entry for 0.4.INTA
pcib0: slot 4 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x3599, revid=0x0c
bus=0, slot=6, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x4018, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
pcib0: matched entry for 0.6.INTA
pcib0: slot 6 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x24d2, revid=0x02
bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
map[20]: type 4, range 32, base 00001400, size 5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x24d4, revid=0x02
bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
map[20]: type 4, range 32, base 00001420, size 5, enabled
pcib0: matched entry for 0.29.INTB
pcib0: slot 29 INTB hardwired to IRQ 19
found-> vendor=0x8086, dev=0x24d7, revid=0x02
bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=7
map[20]: type 4, range 32, base 00001440, size 5, enabled
pcib0: matched entry for 0.29.INTC
pcib0: slot 29 INTC hardwired to IRQ 18
found-> vendor=0x8086, dev=0x24de, revid=0x02
bus=0, slot=29, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
map[20]: type 4, range 32, base 00001460, size 5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x24dd, revid=0x02
bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base dd001000, size 10, enabled
pcib0: matched entry for 0.29.INTD
pcib0: slot 29 INTD hardwired to IRQ 23
found-> vendor=0x8086, dev=0x244e, revid=0xc2
bus=0, slot=30, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x24d0, revid=0x02
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x24db, revid=0x02
bus=0, slot=31, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0288, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
map[20]: type 4, range 32, base 000014a0, size 4, enabled
map[24]: type 1, range 32, base 00000000, size 10, enabled
found-> vendor=0x8086, dev=0x24d3, revid=0x02
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=10
map[20]: type 4, range 32, base 00001100, size 5, enabled
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 17
pci0: <unknown> at device 0.1 (no driver attached)
pci0: <base peripheral> at device 1.0 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 2.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 3
pcib1: I/O decode 0x2000-0x3fff
pcib1: memory decode 0xdd100000-0xdd3fffff
pcib1: prefetched decode 0xfff00000-0xfffff
pcib1: could not get PCI interrupt routing table for \\_SB_.PCI0.PEX0 -
AE_NOT_FOUND
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x8086, dev=0x0329, revid=0x09
bus=1, slot=0, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x0326, revid=0x09
bus=1, slot=0, func=1
class=08-00-20, hdrtype=0x00, mfdev=1
cmdreg=0x0106, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base dd100000, size 12, enabled
pcib1: (null) requested memory range 0xdd100000-0xdd100fff: good
found-> vendor=0x8086, dev=0x032a, revid=0x09
bus=1, slot=0, func=2
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x0327, revid=0x09
bus=1, slot=0, func=3
class=08-00-20, hdrtype=0x00, mfdev=1
cmdreg=0x0106, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base dd101000, size 12, enabled
pcib1: (null) requested memory range 0xdd101000-0xdd101fff: good
pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci1
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0x2000-0x2fff
pcib2: memory decode 0xdd200000-0xdd2fffff
pcib2: prefetched decode 0xfff00000-0xfffff
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
found-> vendor=0x11ab, dev=0x6041, revid=0x03
bus=2, slot=2, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0317, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 64, base dd200000, size 20, enabled
pcib2: (null) requested memory range 0xdd200000-0xdd2fffff: good
pcib1: (null) requested memory range 0xdd200000-0xdd2fffff: good
map[18]: type 4, range 32, base 00002000, size 8, enabled
pcib2: (null) requested I/O range 0x2000-0x20ff: in range
pcib1: (null) requested I/O range 0x2000-0x20ff: in range
pcib2: matched entry for 2.2.INTA
pcib2: slot 2 INTA hardwired to IRQ 32
atapci0: <Marvell 88SX6041 SATA300 controller> port 0x2000-0x20ff mem
0xdd200000-0xdd2fffff irq 32 at device 2.0 on pci2
ioapic1: routing intpin 8 (PCI IRQ 32) to vector 49
atapci0: [MPSAFE]
atapci0: Reserved 0x100000 bytes for rid 0x10 type 3 at 0xdd200000
ata2: <ATA channel 0> on atapci0
ata2: SATA connect ready time=0ms
ata2: sata_connect devices=0x1<ATA_MASTER>
ata2: [MPSAFE]
ata3: <ATA channel 1> on atapci0
ata3: SATA connect ready time=0ms
ata3: sata_connect devices=0x1<ATA_MASTER>
ata3: [MPSAFE]
ata4: <ATA channel 2> on atapci0
ata4: SATA connect ready time=0ms
ata4: sata_connect devices=0x1<ATA_MASTER>
ata4: [MPSAFE]
ata5: <ATA channel 3> on atapci0
ata5: SATA connect ready time=0ms
ata5: sata_connect devices=0x1<ATA_MASTER>
ata5: [MPSAFE]
pci1: <base peripheral, interrupt controller> at device 0.1 (no driver
attached)
pcib3: <ACPI PCI-PCI bridge> at device 0.2 on pci1
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0x3000-0x3fff
pcib3: memory decode 0xdd300000-0xdd3fffff
pcib3: prefetched decode 0xfff00000-0xfffff
pci3: <ACPI PCI bus> on pcib3
pci3: physical bus=3
found-> vendor=0x8086, dev=0x1079, revid=0x03
bus=3, slot=2, func=0
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=7
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 64, base dd300000, size 17, enabled
pcib3: (null) requested memory range 0xdd300000-0xdd31ffff: good
pcib1: (null) requested memory range 0xdd300000-0xdd31ffff: good
map[20]: type 4, range 32, base 00003000, size 6, enabled
pcib3: (null) requested I/O range 0x3000-0x303f: in range
pcib1: (null) requested I/O range 0x3000-0x303f: in range
pcib3: matched entry for 3.2.INTA
pcib3: slot 2 INTA hardwired to IRQ 54
found-> vendor=0x8086, dev=0x1079, revid=0x03
bus=3, slot=2, func=1
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 64, base dd320000, size 17, enabled
pcib3: (null) requested memory range 0xdd320000-0xdd33ffff: good
pcib1: (null) requested memory range 0xdd320000-0xdd33ffff: good
map[20]: type 4, range 32, base 00003040, size 6, enabled
pcib3: (null) requested I/O range 0x3040-0x307f: in range
pcib1: (null) requested I/O range 0x3040-0x307f: in range
pcib3: matched entry for 3.2.INTB
pcib3: slot 2 INTB hardwired to IRQ 55
em0: <Intel(R) PRO/1000 Network Connection Version - 3.2.18> port
0x3000-0x303f mem 0xdd300000-0xdd31ffff irq 54 at device 2.0 on pci3
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xdd300000
em0: Reserved 0x40 bytes for rid 0x20 type 4 at 0x3000
ioapic2: routing intpin 6 (PCI IRQ 54) to vector 50
em0: [MPSAFE]
em0: bpf attached
em0: Ethernet address: 00:00:00:00:00:00
em0: Speed:N/A Duplex:N/A
em1: <Intel(R) PRO/1000 Network Connection Version - 3.2.18> port
0x3040-0x307f mem 0xdd320000-0xdd33ffff irq 55 at device 2.1 on pci3
em1: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xdd320000
em1: Reserved 0x40 bytes for rid 0x20 type 4 at 0x3040
ioapic2: routing intpin 7 (PCI IRQ 55) to vector 51
em1: [MPSAFE]
em1: bpf attached
em1: Ethernet address: 00:00:00:00:00:00
em1: Speed:N/A Duplex:N/A
pci1: <base peripheral, interrupt controller> at device 0.3 (no driver
attached)
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0
pcib4: secondary bus 4
pcib4: subordinate bus 4
pcib4: I/O decode 0xf000-0xfff
pcib4: memory decode 0xfff00000-0xfffff
pcib4: prefetched decode 0xfff00000-0xfffff
pci4: <ACPI PCI bus> on pcib4
pci4: physical bus=4
pcib5: <ACPI PCI-PCI bridge> irq 16 at device 6.0 on pci0
pcib5: secondary bus 5
pcib5: subordinate bus 5
pcib5: I/O decode 0xf000-0xfff
pcib5: memory decode 0xfff00000-0xfffff
pcib5: prefetched decode 0xfff00000-0xfffff
pci5: <ACPI PCI bus> on pcib5
pci5: physical bus=5
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0x1400-0x141f irq
16 at device 29.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1400
ioapic0: routing intpin 16 (PCI IRQ 16) to vector 52
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0x1420-0x143f irq
19 at device 29.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1420
ioapic0: routing intpin 19 (PCI IRQ 19) to vector 53
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0x1440-0x145f irq
18 at device 29.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1440
ioapic0: routing intpin 18 (PCI IRQ 18) to vector 54
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0x1460-0x147f irq
16 at device 29.3 on pci0
uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1460
uhci3: [GIANT-LOCKED]
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801EB/R (ICH5) USB 2.0 controller> mem
0xdd001000-0xdd0013ff irq 23 at device 29.7 on pci0
ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xdd001000
ioapic0: routing intpin 23 (PCI IRQ 23) to vector 55
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801EB/R (ICH5) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib6: secondary bus 6
pcib6: subordinate bus 6
pcib6: I/O decode 0x4000-0x4fff
pcib6: memory decode 0xdd400000-0xdeffffff
pcib6: prefetched decode 0xfff00000-0xfffff
pcib6: Subtractively decoded bridge.
pci6: <ACPI PCI bus> on pcib6
pci6: physical bus=6
found-> vendor=0x1002, dev=0x4752, revid=0x27
bus=6, slot=1, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base de000000, size 24, enabled
pcib6: (null) requested memory range 0xde000000-0xdeffffff: good
map[14]: type 4, range 32, base 00004000, size 8, enabled
pcib6: (null) requested I/O range 0x4000-0x40ff: in range
map[18]: type 1, range 32, base dd400000, size 12, enabled
pcib6: (null) requested memory range 0xdd400000-0xdd400fff: good
pcib6: matched entry for 6.1.INTA
pcib6: slot 1 INTA hardwired to IRQ 17
pci6: <display, VGA> at device 1.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH5 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x14a0-0x14af at device 31.1 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x14a0
ata0: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=00 ostat1=00
ata0: stat0=0x01 err=0x01 lsb=0x01 msb=0x01
ata0: stat1=0x01 err=0x01 lsb=0x01 msb=0x01
ata0: reset tp2 stat0=01 stat1=01 devices=0x0
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 56
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci1: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=00 ostat1=50
ata1: stat0=0x01 err=0x01 lsb=0x01 msb=0x01
ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=01 stat1=00 devices=0x8<ATAPI_SLAVE>
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 57
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 58
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0047
psm0: failed to reset the aux device.
sio0: irq maps: 0x8ca1 0x8cb1 0x8ca1 0x8ca1
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
ioapic0: routing intpin 4 (ISA IRQ 4) to vector 59
sio1: irq maps: 0x8ca1 0x8ca9 0x8ca1 0x8ca1
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ioapic0: routing intpin 3 (ISA IRQ 3) to vector 60
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
acpi0
fdc0: ic_type 90 part_id 73
ioapic0: routing intpin 6 (ISA IRQ 6) to vector 61
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sc: sc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
vga: vga0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xcd7ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
ppc0 failed to probe at irq 7 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
Reducing kern.maxvnodes 134590 -> 100000
procfs registered
lapic: Divisor 2, Frequency 100003698 hz
Timecounter "TSC" frequency 3219347072 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
ata1-slave: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=40 wire
acd0: setting PIO4 on ICH5 chip
acd0: DMA limited to UDMA33, controller found non-ATA66 cable
acd0: setting UDMA33 on ICH5 chip
acd0: <MATSHITADVD-ROM SR-8178/PZ16> DVDROM drive at ata1 as slave
acd0: read 4125KB/s (4125KB/s), 256KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-ROM 120mm data disc
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad4: 143089MB <WDC WD1500ADFD-00NLR1 20.07P20> at ata2-master SATA150
ad4: 293046768 sectors [290721C/16H/63S] 16 sectors/interrupt 1 depth queue
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad6: 143089MB <WDC WD1500ADFD-00NLR1 20.07P20> at ata3-master SATA150
ad6: 293046768 sectors [290721C/16H/63S] 16 sectors/interrupt 1 depth queue
ad6: Adaptec check1 failed
ad6: LSI (v3) check1 failed
ad6: LSI (v2) check1 failed
ad6: FreeBSD check1 failed
ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad8: 143089MB <WDC WD1500ADFD-00NLR1 20.07P20> at ata4-master SATA150
ad8: 293046768 sectors [290721C/16H/63S] 16 sectors/interrupt 1 depth queue
ad8: Adaptec check1 failed
ad8: LSI (v3) check1 failed
ad8: LSI (v2) check1 failed
ad8: FreeBSD check1 failed
ata5-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad10: 143089MB <WDC WD1500ADFD-00NLR1 20.07P20> at ata5-master SATA150
ad10: 293046768 sectors [290721C/16H/63S] 16 sectors/interrupt 1 depth queue
ad10: Adaptec check1 failed
ad10: LSI (v3) check1 failed
ad10: LSI (v2) check1 failed
ad10: FreeBSD check1 failed
ATA PseudoRAID loaded
GEOM: new disk ad4
GEOM: new disk ad6
GEOM: new disk ad8
GEOM: new disk ad10
GEOM_MIRROR: Device gm0 created (id=4151717145).
GEOM_MIRROR: Device gm0: provider ad4 detected.
GEOM_MIRROR: Device gm0: provider ad6 detected.
GEOM_MIRROR: Device gm0: provider ad6 activated.
GEOM_MIRROR: Device gm0: provider ad4 activated.
GEOM_MIRROR: Device gm0: provider mirror/gm0 launched.
GEOM_MIRROR: Device gm1 created (id=429699985).
GEOM_MIRROR: Device gm1: provider ad8 detected.
ad10: WARNING - READ_DMA48 soft error (ECC corrected) LBA=293046767
GEOM_MIRROR: Device gm1: provider ad10 detected.
GEOM_MIRROR: Device gm1: provider ad10 activated.
GEOM_MIRROR: Device gm1: provider ad8 activated.
GEOM_MIRROR: Device gm1: provider mirror/gm1 launched.
ad10: WARNING - READ_DMA soft error (ECC corrected) LBA=225443903
Trying to mount root from ufs:/dev/mirror/gm0s1a
start_init: trying /sbin/init
ad10: WARNING - READ_DMA soft error (ECC corrected) LBA=64
ad10: WARNING - READ_DMA soft error (ECC corrected) LBA=12409711