Hi,
On 12/24/05, iwant4x4jeep <iwant4x4jeep@yandex.ru>
wrote:> I'm upgrade my FreeBSD5.4 system to 6.0-STABLE. Now ACPI suspend-to-ram
(sleepstate #3) don't work ( before upgrade all works fine)
>
> Processor - Pentium 4 2.4Ghz
> Mother Board - ASUS P4PE
>
> # dmesg | grep -i acpi
> ACPI APIC Table: <ASUS P4PE >
>
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C
> MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> acpi0: <ASUS P4PE> on motherboard
> acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 22
> acpi0: Power Button (fixed)
> pci_link0: <ACPI PCI Link LNKA> irq 5 on acpi0
> pci_link1: <ACPI PCI Link LNKB> irq 9 on acpi0
> pci_link2: <ACPI PCI Link LNKC> irq 9 on acpi0
> pci_link3: <ACPI PCI Link LNKD> irq 9 on acpi0
> pci_link4: <ACPI PCI Link LNKE> irq 10 on acpi0
> pci_link5: <ACPI PCI Link LNKF> on acpi0
> pci_link6: <ACPI PCI Link LNKG> on acpi0
> pci_link7: <ACPI PCI Link LNKH> irq 11 on acpi0
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on
acpi0
> cpu0: <ACPI CPU> on acpi0
> acpi_throttle0: <ACPI CPU Throttling> on cpu0
> acpi_button0: <Power Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pci2: <ACPI PCI bus> on pcib2
> fdc0: <floppy drive controller> port 0x3f2-0x3f5,0x3f7 irq 6 drq 2 on
acpi0
> ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7
drq 3 on ac
> pi0
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10
on acpi0
> sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
>
> When I (as usually before) enter in console 'acpiconf -s 3' (Really
I use sudo, so type 'sudo acpiconf -s 3', computer suspends, but
don't resume after power on.
>
> I have problem with hi-ressolution modes in console ( Using pathes from
DragonFlyBSD project, which is allready included with freebsd since 6.0).
> I'm enabled VESA and SC_PIXEL_MODE options in kernel, when I enter
'vidcontrol -i mode' - all modes(what i need) displays, but if I use
vidcontrol MODE_279 (for example), monitor enter 1024x768 mode, but I can't
see anything.
> First time I think that I do something wrong (Don't load needed fonts
for example), but when I try it on another computer- I can't believe my
eyes.. It was real 1024x768 in FreeBSD Console !!!
Are you sure that your configuration cacn support MODE_279? Will
other modes work?
Cheers,
--
Xin LI <delphij@delphij.net> http://www.delphij.net