I just picked up a new ABIT NF7-S2G motherboard (NF2 MCP chip set with
gigE and SATA/RAID). I'm running 5.3 release on it. The standard
parallel ATA chipset returns a "known" id . The SATA i/f seems to be
too new, and freebsd treats it like an unknown udma33 controller.
There's no Marvel bridge on the mobo. Is this a true SATA interface?
Should I be able to get away with putting entries in the following? (i'm
not concerned about the raid thing). They curently work as udma33 disks.
thanks
jim
ata-pci.h:#define ATA_NFORCE2_MCP2 0x008e10de
ata-chipset.c: { ATA_NFORCE2_MCP2, 0, AMDNVIDIA, NVIDIA, ATA_UDMA6,
"nVidia nForce2 MCP2" },
pciconf -lv says...
atapci0@pci0:9:0: class=0x01018a card=0x1c08147b chip=0x008510de
rev=0xa3 hdr=0x00
vendor = 'NVIDIA Corporation'
device = 'MCP2S Parallel ATA Controller'
class = mass storage
subclass = ATA
atapci1@pci0:11:0: class=0x010185 card=0x1c08147b chip=0x008e10de
rev=0xa3 hdr=0x00
vendor = 'NVIDIA Corporation'
device = 'MCP2S Serial ATA Compatible Controller'
class = mass storage
subclass = ATA
dmesg says...
atapci0: <nVidia nForce2 MCP UDMA133 controller> port
0xf000-0xf00f,0x376,0x170-
0x177,0x3f6,0x1f0-0x1f7 at device 9.0 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
atapci1: <GENERIC ATA controller> port
0xcc00-0xcc0f,0xb70-0xb73,0x970-0x977,0xb
f0-0xbf3,0x9f0-0x9f7 irq 11 at device 11.0 on pci0
Just for completeness, they use the VIA vge driven chip.
pciconf says...
vge0@pci2:11:0: class=0x020000 card=0x1c08147b chip=0x31191106 rev=0x11
hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT3119 Rhine-GE Gigabit Ethernet Controller'
class = network
subclass = ethernet
desg says...
vge0: <VIA Networking Gigabit Ethernet> port 0xb000-0xb0ff mem
0xe8000000-0xe800
00ff irq 10 at device 11.0 on pci2
miibus0: <MII bus> on vge0
ciphy0: <Cicada CS8201 10/100/1000TX PHY> on miibus0
ciphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
secmgr wrote:> I just picked up a new ABIT NF7-S2G motherboard (NF2 MCP chip set with > gigE and SATA/RAID). I'm running 5.3 release on it. The standard > parallel ATA chipset returns a "known" id . The SATA i/f seems to be > too new, and freebsd treats it like an unknown udma33 controller. > There's no Marvel bridge on the mobo. Is this a true SATA interface? > Should I be able to get away with putting entries in the following? > (i'm not concerned about the raid thing). They curently work as > udma33 disks. > > thanks > jim > > ata-pci.h:#define ATA_NFORCE2_MCP2 0x008e10de > ata-chipset.c: { ATA_NFORCE2_MCP2, 0, AMDNVIDIA, NVIDIA, > ATA_UDMA6, "nVidia nForce2 MCP2" },well, to follow up my own mail, the trick above didn't help. the ata code still thinks it's a brain dead ata device and limits it to UDMA33. Help! When I looked through the H/W compat list, it said that Nforce 2 was supported, which is why I felt confident buying the board. I'd really like to get this working at SATA 150, even if the current drives might be bridged. Failing that, is there a definitive list of SATA PCI boards which FreeBSD does full support? thanks jim atapci0: <nVidia nForce2 MCP UDMA133 controller> port 0xf000-0xf00f,0x376,0x170- 0x177,0x3f6,0x1f0-0x1f7 at device 9.0 on pci0 ata0: channel #0 on atapci0 ata1: channel #1 on atapci0 atapci1: <nVidia nForce2 MCP2 UDMA133 controller> port 0xcc00-0xcc0f,0xb70-0xb73 ,0x970-0x977,0xbf0-0xbf3,0x9f0-0x9f7 irq 11 at device 11.0 on pci0 ata2: channel #0 on atapci1 ata3: channel #1 on atapci1 . .ata2-master: DMA limited to UDMA33, non-ATA66 cable or device ad4: 152627MB <SAMSUNG SP1614C/SW100-30> [310101/16/63] at ata2-master UDMA33 ata3-master: DMA limited to UDMA33, non-ATA66 cable or device ad6: 152627MB <SAMSUNG SP1614C/SW100-30> [310101/16/63] at ata3-master UDMA33