Hello.
I have Fujitsu-Siemens Primergy L200 server. It is running 5.2-CURRENT
at the moment. When I tried to upgrade it to 5.3-STABLE, new kernel hung
at boot. Luckily, this server has NMI button, so I have hand transcribed
stack trace (no serial console, sorry):
vm_page_alloc_contig()+0xbe
contig_malloc()+0x97
alloc_bounce_pages()+0x60
bus_dmamap_create()+0x103
sym_alloc_ccb()+0x75
sym_pci_attach()+0x6b6
device_attach()+0x58
... then follows usual probing trace
I tried disabling ACPI and APIC with no luck. Below is s dmesg from
running 5.2-CURRENT with the pointer where 5.3-STABLE hangs.
Is this known problem? Are there workarounds?
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2-CURRENT #2: Wed Jun 9 14:45:42 MSD 2004
mcsi@mail3.ezone.ru:/usr/obj/usr/src/sys/MAIL3
Preloaded elf kernel "/boot/kernel.old/kernel" at 0xc09ca000.
Preloaded elf module "/boot/kernel.old/acpi.ko" at 0xc09ca298.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) III CPU - S 1400MHz (1393.30-MHz
686-class CPU)
Origin = "GenuineIntel" Id = 0x6b4 Stepping = 4
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 1073741824 (1024 MB)
avail memory = 1041207296 (992 MB)
random: <entropy source, Software, Yarrow>
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD RSDT> on motherboard
acpi0: [GIANT-LOCKED]
pcibios: BIOS version 2.10
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0xf008-0xf00b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 10 INTA is routed to irq 10
pcib0: slot 11 INTA is routed to irq 9
pci0: <display, VGA> at device 4.0 (no driver attached)
fxp0: <Intel 82559ER Pro/100 Ethernet> port 0x1400-0x143f mem
0xfc000000-0xfc01ffff,0xfc041000-0xfc041fff irq 10 at device 10.0 on pci0
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:30:05:1f:b3:49
fxp0: [GIANT-LOCKED]
fxp1: <Intel 82559ER Pro/100 Ethernet> port 0x1800-0x183f mem
0xfc020000-0xfc03ffff,0xfc042000-0xfc042fff irq 9 at device 11.0 on pci0
miibus1: <MII bus> on fxp1
inphy1: <i82555 10/100 media interface> on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: Ethernet address: 00:30:05:1f:ec:6f
fxp1: [GIANT-LOCKED]
isab0: <PCI-ISA bridge> port 0xf100-0xf10f at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 UDMA33 controller> port
0x1c00-0x1c0f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcib1: <ACPI Host-PCI bridge> on acpi0
pci1: <ACPI PCI bus> on pcib1
pcib1: slot 10 INTA is routed to irq 5
sym0: <1010-66> port 0x2000-0x20ff mem
0xfe000000-0xfe001fff,0xfe002000-0xfe0023ff irq 5 at device 10.0 on pci1
sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: handling phase mismatch from SCRIPTS.
<--- Here it freezes in 5.3-STABLE. It doesnt output next (GIANT-LOCKED)
line.
sym0: [GIANT-LOCKED]
pcib2: <ACPI Host-PCI bridge> on acpi0
pci2: <ACPI PCI bus> on pcib2
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
orm0: <Option ROMs> at iomem 0xc9000-0xccfff,0xc0000-0xc8fff on isa0
pmtimer0 on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1393303550 Hz quality 800
Timecounters tick every 1.000 msec
ipfw2 initialized, divert enabled, rule-based forwarding enabled,
default to deny, logging limited to 100 packets/entry by default
acd0: CDROM <SR244W> at ata1-master PIO4
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
(probe7:sym0:0:8:0): phase change 6-7 6@3e772d8c resid=4.
ses0 at sym0 bus 0 target 8 lun 0
ses0: <SDR GEM318 0> Fixed Processor SCSI-2 device
ses0: 3.300MB/s transfers
ses0: SAF-TE Compliant Device
da0 at sym0 bus 0 target 0 lun 0
da0: <FUJITSU MAN3367MC 5207> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz, offset 62, 16bit), Tagged
Queueing Enabled
da0: 35044MB (71771688 512 byte sectors: 255H 63S/T 4467C)
Mounting root from ufs:/dev/da0s1a
--
Maxim Maximov