vizion communication
2003-Apr-23 21:50 UTC
Fw: Anyone please???? SMP & general health check!!
I put this to the smp list and to stable but have had no takers from wither. nThere are both smp and other system issues and I am just wondering if anyoe would be willing to take a look at this output from dmesg and let me have some advice Thanks david ----- Original Message ----- From: "vizion communication" <vizion@ixpres.com> To: <freebsd-smp@freebsd.org> Sent: Wednesday, April 23, 2003 9:03 PM Subject: Anyone please???? SMP health check!!> I posted this a few days back but have had no takers... > > I hope you will not mind if I repeat the query?? > > David > ----- Original Message ----- > From: "vizion communication" <vizion@ixpres.com> > To: <freebsd-smp@freebsd.org> > Sent: Monday, April 21, 2003 8:23 AM > Subject: SMP health check!! > > > > Hi > > > > OK I have a quad processor proliant 5500 and amuncertain> > whether I am getting the performance I would expect from > it. > > > > There are entries in dmesg which clearly relate to SMP I > do > > not understand so here is all the output -- comments & > > guidance appreciated. > > > > ---------------------------------------------------------- > > > > Copyright (c) 1992-2002 The FreeBSD Project. > > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, > > 1992, 1993, 1994 > > The Regents of the University of California. All rights > > reserved. > > FreeBSD 4.7-RELEASE #0: Sun Feb 16 17:25:33 PST 2003 > > root@dns3.vizion2000.net:/usr/obj/usr/src/sys/COMPAQ > > Timecounter "i8254" frequency 1193182 Hz > > CPU: Pentium III/Pentium III Xeon/Celeron (499.84-MHz > > 686-class CPU) > > Origin = "GenuineIntel" Id = 0x672 Stepping = 2 > > > > >Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,S> > EP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > > real memory = 2147467264 (2097136K bytes) > > config> di sn0 > > config> di lnc0 > > config> di ie0 > > config> di fe0 > > config> di cs0 > > config> q > > avail memory = 2086445056 (2037544K bytes) > > APIC_IO: MP table broken: 8259->APIC entry missing! > > Changing APIC ID for IO APIC #0 from 0 to 8 on chip > > Programming 35 pins in IOAPIC #0 > > IOAPIC #0 intpin 2 -> irq 0 > > FreeBSD/SMP: Multiprocessor motherboard > > cpu0 (BSP): apic id: 3, version: 0x00040011, at > 0xfee00000 > > cpu1 (AP): apic id: 0, version: 0x00040011, at > 0xfee00000 > > cpu2 (AP): apic id: 1, version: 0x00040011, at > 0xfee00000 > > cpu3 (AP): apic id: 2, version: 0x00040011, at > 0xfee00000 > > io0 (APIC): apic id: 8, version: 0x00220011, at > 0xfec00000 > > Preloaded elf kernel "kernel" at 0xc051f000. > > Preloaded userconfig_script "/boot/kernel.conf" at > > 0xc051f09c. > > Pentium Pro MTRR support enabled > > md0: Malloc disk > > npx0: <math processor> on motherboard > > npx0: INT 16 interface > > pcib0: <Intel 82454NX PXB#0, Bus#A> on motherboard > > pci0: <PCI bus> on pcib0 > > pcib1: <PCI to PCI bridge (vendor=8086 device=5200)> at > > device 1.0 on pci0 > > pci1: <PCI bus> on pcib1 > > pci0: <unknown card> (vendor=0x8086, dev=0x5201) at 1.1 > irq > > 9 > > pci0: <NVidia Riva Ultra Vanta TNT2 graphicsaccelerator>> at > > 2.0 irq 5 > > pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 12.0 > > sym0: <875> port 0x2000-0x20ff mem > > 0xc4fd0000-0xc4fd0fff,0xc4fe0000-0xc4fe00ff irq 10 at > device > > 13.0 on pci0 > > sym0: No NVRAM, ID 7, Fast-20, SE, parity checking > > sym1: <875> port 0x2400-0x24ff mem > > 0xc4fb0000-0xc4fb0fff,0xc4fc0000-0xc4fc00ff irq 15 at > device > > 13.1 on pci0 > > sym1: No NVRAM, ID 7, Fast-20, SE, parity checking > > pci0: <ATI Mach64-GV graphics accelerator> at 14.0 > > isab0: <Intel 82371AB PCI to ISA bridge> at device 15.0on> > pci0 > > isa0: <ISA bus> on isab0 > > atapci0: <Intel PIIX4 ATA33 controller> port0x2c00-0x2c0f> > at device 15.1 on pci0 > > ata0: at 0x1f0 irq 14 on atapci0 > > ata1: at 0x170 irq 15 on atapci0 > > uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port > > 0x2c20-0x2c3f at device 15.2 on pci0 > > pci_cfgintr: can't route an interrupt to 0:15 INTD > > uhci0: Could not allocate irq > > device_probe_and_attach: uhci0 attach returned 6 > > Timecounter "PIIX" frequency 3579545 Hz > > chip0: <Intel 82371AB Power management controller> port > > 0x1240-0x124f at device 15.3 on pci0 > > pcib2: <Intel 82454NX PCI Expander Bridge> at device18.0> on > > pci0 > > pcib3: <Intel 82454NX PCI Expander Bridge> at device19.0> on > > pci0 > > pcib4: <Intel 82454NX PXB#0, Bus#B> on motherboard > > pci4: <PCI bus> on pcib4 > > pcib5: <IBM 82351 PCI-PCI bridge> at device 1.0 on pci4 > > pci5: <PCI bus> on pcib5 > > ida0: <Compaq Smart Array 3200 controller> port > > 0x4000-0x40ff mem 0xc6ef0000-0xc6ef00ff irq 15 at device > 0.0 > > on pci5 > > ida0: drives=4 firm_rev=4.06 > > idad0: <Compaq Logical Drive> on ida0 > > idad0: 24997MB (51195840 sectors), blocksize=512 > > idad1: <Compaq Logical Drive> on ida0 > > idad1: 14997MB (30714240 sectors), blocksize=512 > > idad2: <Compaq Logical Drive> on ida0 > > idad2: 12096MB (24773760 sectors), blocksize=512 > > idad3: <Compaq Logical Drive> on ida0 > > idad3: 26029MB (53309280 sectors), blocksize=512 > > ahc0: <Adaptec 2940 SCSI adapter> port 0x3000-0x30ff mem > > 0xc6df0000-0xc6df0fff irq 11 at device 2.0 on pci4 > > aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs > > pcib6: <DEC 21152 PCI-PCI bridge> at device 5.0 on pci4 > > pci6: <PCI bus> on pcib6 > > de0: <Digital 21140A Fast Ethernet> port 0x5000-0x507fmem> > 0xc6ff0000-0xc6ff007f irq 9 at device 4.0 on pci6 > > de0: Cogent EM440TX 21140A [10-100Mb/s] pass 2.2 > > de0: address 00:00:d1:1c:c4:f9 > > de1: <Digital 21140A Fast Ethernet> port 0x5080-0x50ffmem> > 0xc6fe0000-0xc6fe007f irq 9 at device 5.0 on pci6 > > de1: Cogent EM440TX 21140A [10-100Mb/s] pass 2.2 > > de1: address 00:00:d1:1c:c4:fa > > de2: <Digital 21140A Fast Ethernet> port 0x5400-0x547fmem> > 0xc6fd0000-0xc6fd007f irq 9 at device 6.0 on pci6 > > de2: Cogent EM440TX 21140A [10-100Mb/s] pass 2.2 > > de2: address 00:00:d1:1c:c4:fb > > de3: <Digital 21140A Fast Ethernet> port 0x5480-0x54ffmem> > 0xc6fc0000-0xc6fc007f irq 9 at device 7.0 on pci6 > > de3: Cogent EM440TX 21140A [10-100Mb/s] pass 2.2 > > de3: address 00:00:d1:1c:c4:fc > > eisa0: <EISA bus> on motherboard > > mainboard0: <CPQ0808 (System Board)> on eisa0 slot 0 > > orm0: <Option ROMs> at iomem > 0xe8000-0xedfff,0xee000-0xeffff > > on isa0 > > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7irq> 6 > > drq 2 on isa0 > > fdc0: FIFO enabled, 8 bytes threshold > > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 > on > > isa0 > > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > > kbd0 at atkbd0 > > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > > psm0: model IntelliMouse Explorer, device ID 4 > > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem > > 0xa0000-0xbffff on isa0 > > sc0: <System console> at flags 0x100 on isa0 > > sc0: VGA <16 virtual consoles, flags=0x300> > > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > > sio0: type 16550A > > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > > sio1: type 16550A > > ppc0: cannot reserve I/O port range > > APIC_IO: Testing 8254 interrupt delivery > > APIC_IO: routing 8254 via IOAPIC #0 intpin 2 > > SMP: AP CPU #3 Launched! > > SMP: AP CPU #1 Launched! > > SMP: AP CPU #2 Launched! > > acd0: CDROM <CDU5211> at ata0-master PIO4 > > Waiting 15 seconds for SCSI devices to settle > > de1: enabling Full Duplex 100baseTX port > > de0: enabling 10baseT port > > de2: enabling 10baseT port > > de0: link down: cable problem? > > de2: link down: cable problem? > > de3: autosense failed: cable problem? > > (probe31:ahc0:0:1:0): SCB 0x5 - timed out > > ahc0: Dumping Card State in Message-out phase, atSEQADDR> > 0xe3 > > ACCUM = 0xa0, SINDEX = 0x61, DINDEX = 0x8c, ARG_2 = 0x0 > > HCNT = 0x0 SCBPTR = 0x2 > > SCSISEQ = 0x12, SBLKCTL = 0x0 > > DFCNTRL = 0x0, DFSTATUS = 0x29 > > LASTPHASE = 0xa0, SCSISIGI = 0xb6, SXFRCTL0 = 0x88 > > SSTAT0 = 0x7, SSTAT1 = 0x3 > > STACK == 0xe1, 0xfb, 0x156, 0x0 > > SCB count = 10 > > Kernel NEXTQSCB = 7 > > Card NEXTQSCB = 3 > > QINFIFO entries: 3 2 9 8 > > Waiting Queue entries: > > Disconnected Queue entries: 1:5 > > QOUTFIFO entries: > > Sequencer Free SCB List: 0 3 4 5 6 7 8 9 10 11 12 13 1415> > Sequencer SCB Info: 0(c 0x40, s 0x7, l 0, t 0xff) 1(c > 0x44, > > s 0x17, l 0, t 0x5) 2(c 0x40, s 0x27, l 0, t 0x4) 3(c0x0,> s > > 0xff, l 255, t 0xff) 4(c 0x0, s 0xff, l 255, t 0xff) 5(c > > 0x0, s 0xff, l 255, t 0xff) 6(c 0x0, s 0xff, l 255, t > 0xff) > > 7(c 0x0, s 0xff, l 255, t 0xff) 8(c 0x0, s 0xff, l 255,t> > 0xff) 9(c 0x0, s 0xff, l 255, t 0xff) 10(c 0x0, s 0xff,l> > 255, t 0xff) 11(c 0x0, s 0xff, l 255, t 0xff) 12(c 0x0,s> > 0xff, l 255, t 0xff) 13(c 0x0, s 0xff, l 255, t 0xff)14(c> > 0x0, s 0xff, l 255, t 0xff) 15(c 0x0, s 0xff, l 255, t > 0xff) > > Pending list: 8(c 0x40, s 0x7, l 1), 9(c 0x50, s 0x67, l > 0), > > 2(c 0x50, s 0x57, l 0), 3(c 0x50, s 0x47, l 0), 4(c0x40,> s > > 0x27, l 0), 5(c 0x40, s 0x17, l 0) > > Kernel Free SCB list: 6 1 0 > > Untagged Q(0): 8 > > Untagged Q(1): 5 > > Untagged Q(2): 4 > > Untagged Q(4): 3 > > Untagged Q(5): 2 > > Untagged Q(6): 9 > > (probe31:ahc0:0:1:0): Other SCB Timeout > > (probe32:ahc0:0:2:0): SCB 0x4 - timed out > > ahc0: Dumping Card State in Message-out phase, atSEQADDR> > 0x15c > > ACCUM = 0xa0, SINDEX = 0x61, DINDEX = 0x8c, ARG_2 = 0x0 > > HCNT = 0x0 SCBPTR = 0x2 > > SCSISEQ = 0x12, SBLKCTL = 0x0 > > DFCNTRL = 0x0, DFSTATUS = 0x29 > > LASTPHASE = 0xa0, SCSISIGI = 0xb6, SXFRCTL0 = 0x88 > > SSTAT0 = 0x7, SSTAT1 = 0x3 > > STACK == 0xfb, 0x156, 0x0, 0xe1 > > SCB count = 10 > > Kernel NEXTQSCB = 7 > > Card NEXTQSCB = 3 > > QINFIFO entries: 3 2 9 8 > > Waiting Queue entries: > > Disconnected Queue entries: 1:5 > > QOUTFIFO entries: > > Sequencer Free SCB List: 0 3 4 5 6 7 8 9 10 11 12 13 1415> > Sequencer SCB Info: 0(c 0x40, s 0x7, l 0, t 0xff) 1(c > 0x44, > > s 0x17, l 0, t 0x5) 2(c 0x40, s 0x27, l 0, t 0x4) 3(c0x0,> s > > 0xff, l 255, t 0xff) 4(c 0x0, s 0xff, l 255, t 0xff) 5(c > > 0x0, s 0xff, l 255, t 0xff) 6(c 0x0, s 0xff, l 255, t > 0xff) > > 7(c 0x0, s 0xff, l 255, t 0xff) 8(c 0x0, s 0xff, l 255,t> > 0xff) 9(c 0x0, s 0xff, l 255, t 0xff) 10(c 0x0, s 0xff,l> > 255, t 0xff) 11(c 0x0, s 0xff, l 255, t 0xff) 12(c 0x0,s> > 0xff, l 255, t 0xff) 13(c 0x0, s 0xff, l 255, t 0xff)14(c> > 0x0, s 0xff, l 255, t 0xff) 15(c 0x0, s 0xff, l 255, t > 0xff) > > Pending list: 8(c 0x40, s 0x7, l 1), 9(c 0x50, s 0x67, l > 0), > > 2(c 0x50, s 0x57, l 0), 3(c 0x50, s 0x47, l 0), 4(c0x40,> s > > 0x27, l 0), 5(c 0x40, s 0x17, l 0) > > Kernel Free SCB list: 6 1 0 > > Untagged Q(0): 8 > > Untagged Q(1): 5 > > Untagged Q(2): 4 > > Untagged Q(4): 3 > > Untagged Q(5): 2 > > Untagged Q(6): 9 > > (probe32:ahc0:0:2:0): BDR message in message buffer > > (probe32:ahc0:0:2:0): no longer in timeout, status = 300 > > Mounting root from ufs:/dev/idad0s1a > > da0 at ahc0 bus 0 target 0 lun 0 > > da0: <SEAGATE ST34371N 0280> Fixed Direct Access SCSI-2 > > device > > da0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged > > Queueing Enabled > > da0: 4148MB (8496960 512 byte sectors: 64H 32S/T 4148C) > > da3 at ahc0 bus 0 target 4 lun 0 > > da3: <SEAGATE ST34371N 0280> Fixed Direct Access SCSI-2 > > device > > da3: 10.000MB/s transfers (10.000MHz, offset 15), Tagged > > Queueing Enabled > > da3: 4148MB (8496960 512 byte sectors: 64H 32S/T 4148C) > > da2 at ahc0 bus 0 target 2 lun 0 > > da2: <SEAGATE ST34371N 0484> Fixed Direct Access SCSI-2 > > device > > da2: 10.000MB/s transfers (10.000MHz, offset 15), Tagged > > Queueing Enabled > > da2: 4148MB (8496884 512 byte sectors: 64H 32S/T 4148C) > > da5 at ahc0 bus 0 target 6 lun 0 > > da5: <SEAGATE ST15150N 0023> Fixed Direct Access SCSI-2 > > device > > da5: 10.000MB/s transfers (10.000MHz, offset 15), Tagged > > Queueing Enabled > > da5: 4095MB (8388315 512 byte sectors: 64H 32S/T 4095C) > > da4 at ahc0 bus 0 target 5 lun 0 > > da4: <SEAGATE ST15150N 0023> Fixed Direct Access SCSI-2 > > device > > da4: 10.000MB/s transfers (10.000MHz, offset 15), Tagged > > Queueing Enabled > > da4: 4095MB (8388315 512 byte sectors: 64H 32S/T 4095C) > > da1 at ahc0 bus 0 target 1 lun 0 > > da1: <SEAGATE ST34371N 0484> Fixed Direct Access SCSI-2 > > device > > da1: 10.000MB/s transfers (10.000MHz, offset 15), Tagged > > Queueing Enabled > > da1: 4148MB (8496884 512 byte sectors: 64H 32S/T 4148C) > > > > _______________________________________________ > freebsd-smp@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-smp > To unsubscribe, send any mail to"freebsd-smp-unsubscribe@freebsd.org">
On Wed, Apr 23, 2003 at 09:21:52PM -0700, vizion communication wrote:> I put this to the smp list and to stable but have had no > takers from wither. nThere are both smp and other system > issues and I am just wondering if anyoe would be willing to > take a look at this output from dmesg and let me have some > advice >You should trim up the dmesg output, and highlight the items that concern you. Offhand, I don't see anything there that seems out of place. Bruce -- ------------------------------------------------------------------------ "I like bad!" Bruce Burden Austin, TX. - Thuganlitha The Power and the Prophet Robert Don Hughes
vizion communication wrote:> I put this to the smp list and to stable but have had no > takers from wither. nThere are both smp and other system > issues and I am just wondering if anyoe would be willing to > take a look at this output from dmesg and let me have some > advice >You should just move to the -CURRENT branch. 4.x has SMP, but it's not really how SMP should be implemented. The 5.x branch has started true fine-grained SMP and is the direction for you to go IMO. 5.1-RELEASE will be out soon and should be stable for you. Pete... P.S. You could just forget the whole thing and send me that quad proc beast. :-)