CentOS - Dec 2007 - CentOS 5.1 on intel DQ35JO , Q35 chipsed based board

Hi,
i was trying to install CentOS 5.1 on new machine based on Intel Q35 desktop
board, witch 2 SATA disks (configured as RAID 1) , 8GB RAM and Intel Core2
QUADCORE.
The first problem was with install - it hangs before installer startup at
ACPI messages. So i installed it with ACPI=off switch.

The first problem is :
Dec  7 09:54:01 vmhost1 kernel: BIOS bug, no explicit IRQ entries, using
default mptable. (tell your hw vendor)
Dec  7 09:54:01 vmhost1 kernel: Processors: 1
Which kernel should i use? I have default installed kernel.


The second problem is with LVM (probably raid on board - in bios i switched
in sata mode to raid, and created in raid utility RAID1 volume from those 2
disks:

  /dev/sdb1                [      101.94 MB]
  Found duplicate PV hpGVb3U5Q0lxFe1LN6eJpSCJSWs0xfpu: using /dev/sdb2 not
/dev/sda2
  /dev/sdb2                [      297.99 GB] LVM physical volume
[root at vmhost1 archive]#
What does it means and how can i fix this?

Thanks a lot

David Hlacik
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://lists.centos.org/pipermail/centos/attachments/20071207/9884d0ae/attachment-0003.html>

David Hl??ik wrote:
> Hi,
> i was trying to install CentOS 5.1 on new machine based on Intel Q35 
> desktop board, witch 2 SATA disks (configured as RAID 1) , 8GB RAM and 
> Intel Core2 QUADCORE.
> The first problem was with install - it hangs before installer startup 
> at ACPI messages. So i installed it with ACPI=off switch.
> The first problem is :
> Dec 7 09:54:01 vmhost1 kernel: BIOS bug, no explicit IRQ entries, 
> using default mptable. (tell your hw vendor)
> Dec 7 09:54:01 vmhost1 kernel: Processors: 1
> Which kernel should i use? I have default installed kernel.
update the BIOS to the latest, make sure you do a CMOS reset to 
defaults, and turn ACPI back on and try again.....

ahhh after I wrote that previous line, I googled `linux dq35jo` and 
found http://kbase.redhat.com/faq/FAQ_103_11855.shtm about 5 hits down.

Issue:
Why does my Intel DQ35JO or DQ35MP-based system not boot when
I try to perform the initial installation of Red Hat Enterprise Linux 5.1?

Resolution:

The Intel DQ35JO and DQ35MP systems require the specific boot parameter 
pci=nommconf
to boot during the initial installation of Red Hat Enterprise Linux 5.1 
(RHEL5.1).

The parameter is not needed after installation.


> The second problem is with LVM (probably raid on board - in bios i 
> switched in sata mode to raid, and created in raid utility RAID1 
> volume from those 2 disks:
>
> /dev/sdb1 [ 101.94 MB]
> Found duplicate PV hpGVb3U5Q0lxFe1LN6eJpSCJSWs0xfpu: using /dev/sdb2 
> not /dev/sda2
> /dev/sdb2 [ 297.99 GB] LVM physical volume
> [root at vmhost1 archive]#
> What does it means and how can i fix this?

turn that fake raid crap off, and use linux software raid instead. 
Anaconda makes combining linux raid mirroring and LVM a bit tricky at 
setup time, but it -can- be done. custom disk partitioning, delete all 
partitions, create a 120MB /boot on both drives, create a raid1 mirror 
on the rest of the two drives, then create LVM partition(s) as / (and 
/var,/home, whatever if you want several seperate file systems, your 
choice) in that raid metadisk, and install to that.