Hello, I have the following setup: 1. Ubuntu Dapper Server 6.06 plus latest patches 2. Asterisk 1.2.11 3. libpri 1.2.3 4. Zaptel 1.2.8 5. Digium TDM22 (TDM400P) 6. Analog phone plugged in port 3 7. The wctdm, zaptel modules load at startup, I type asterisk as root and it is activated. 8. I check the Channel Map and I have the following: Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels configured. I can ssh into the server and remotely connect to the server. Great! The card is not connected to an outside line as of yet but I have no dialtone on the phone. I spoke with a rep. at digium and was told a dialtone should be there. Zaptel.conf : loadzone=us defaultzone=us fxoks=1,2 fxsks=3,4 Zapata.conf: ;FXS Modules signalling=fxo_ks channel => 1,2 ; ;FXO Modules signalling=fxs_ks channel => 3,4 I made sure the card is not sharing an IRQ, I checked the hard drive and all is well. I load zttool and get the following: cat /proc/zaptel/* Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1" 1 WCTDM/0/0 2 WCTDM/0/1 3 WCTDM/0/2 4 WCTDM/0/3 Any suggestions? Ed -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061005/9006678d/attachment.htm
Hi Ed -> 5. Digium TDM22 (TDM400P) > 6. Analog phone plugged in port 3> Channel 01: FXO Kewlstart (Default) (Slaves: 01) > Channel 02: FXO Kewlstart (Default) (Slaves: 02) > Channel 03: FXS Kewlstart (Default) (Slaves: 03) > Channel 04: FXS Kewlstart (Default) (Slaves: 04) > > Zaptel.conf : > loadzone=us > defaultzone=us > fxoks=1,2 > fxsks=3,4 > > Zapata.conf: > ;FXS Modules > signalling=fxo_ks > channel => 1,2 > > ;FXO Modules > signalling=fxs_ks > channel => 3,4 > > Any suggestions?It looks like you may have the phone plugged into the wrong port. You have port 3 listed as an FXO module. You want to plug the phone into an FXS port. - Noah
Did you set immediate=no in zapata.conf? Francesco Eddie Johnson Jr wrote:> > > > Hello, > > > > I have the following setup: > > > > 1. Ubuntu Dapper Server 6.06 plus latest patches > > > > 2. Asterisk 1.2.11 > > > > 3. libpri 1.2.3 > > > > 4. Zaptel 1.2.8 > > > > 5. Digium TDM22 (TDM400P) > > > > 6. Analog phone plugged in port 3 > > > > 7. The wctdm, zaptel modules load at startup, I type asterisk as root and > > it is activated. > > > > 8. I check the Channel Map and I have the following: > > > > > > Channel map: > > > > Channel 01: FXO Kewlstart (Default) (Slaves: 01) > > Channel 02: FXO Kewlstart (Default) (Slaves: 02) > > Channel 03: FXS Kewlstart (Default) (Slaves: 03) > > Channel 04: FXS Kewlstart (Default) (Slaves: 04) > > > > 4 channels configured. > > > > I can ssh into the server and remotely connect to the server. Great! > The card is not connected to an outside line as of yet but I have no > dialtone on the phone. I spoke with a rep. at digium and was told a > dialtone should be there. > > > > Zaptel.conf : > > > > > > loadzone=us > > defaultzone=us > > fxoks=1,2 > > fxsks=3,4 > > > > Zapata.conf: > > > > ;FXS Modules > > signalling=fxo_ks > > channel => 1,2 > > ; > > ;FXO Modules > > signalling=fxs_ks > > channel => 3,4 > > > > I made sure the card is not sharing an IRQ, I checked the hard drive > and all is well. I load zttool and get the following: > > > > cat /proc/zaptel/* > > Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1" > > > > 1 WCTDM/0/0 > > 2 WCTDM/0/1 > > 3 WCTDM/0/2 > > 4 WCTDM/0/3 > > > > Any suggestions? > > > > Ed > > > > ------------------------------------------------------------------------ > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
Yes, I have and I received the following: In zapata.conf your first two channels should be fxs_ks because the first two modules are FXO mdoules. Your last two channels should be fxo_ks because the second two modules are FXS modules. For the TDM400P(TDM 22) the FXS modules work with the phone. The 3 port is for the line. So I unplugged it from port 3, and plugged the analog phone in port 1, made the changes to the channels and set immediate=no, restart the server and activated asterisk. Nothing, my friend. Any more suggestions, Ed -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Francesco Francesconi Sent: Friday, October 06, 2006 10:23 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] No Dialtone Did you set immediate=no in zapata.conf? Francesco Eddie Johnson Jr wrote:> > > > Hello, > > > > I have the following setup: > > > > 1. Ubuntu Dapper Server 6.06 plus latest patches > > > > 2. Asterisk 1.2.11 > > > > 3. libpri 1.2.3 > > > > 4. Zaptel 1.2.8 > > > > 5. Digium TDM22 (TDM400P) > > > > 6. Analog phone plugged in port 3 > > > > 7. The wctdm, zaptel modules load at startup, I type asterisk as root and > > it is activated. > > > > 8. I check the Channel Map and I have the following: > > > > > > Channel map: > > > > Channel 01: FXO Kewlstart (Default) (Slaves: 01) > > Channel 02: FXO Kewlstart (Default) (Slaves: 02) > > Channel 03: FXS Kewlstart (Default) (Slaves: 03) > > Channel 04: FXS Kewlstart (Default) (Slaves: 04) > > > > 4 channels configured. > > > > I can ssh into the server and remotely connect to the server. Great! > The card is not connected to an outside line as of yet but I have no > dialtone on the phone. I spoke with a rep. at digium and was told a > dialtone should be there. > > > > Zaptel.conf : > > > > > > loadzone=us > > defaultzone=us > > fxoks=1,2 > > fxsks=3,4 > > > > Zapata.conf: > > > > ;FXS Modules > > signalling=fxo_ks > > channel => 1,2 > > ; > > ;FXO Modules > > signalling=fxs_ks > > channel => 3,4 > > > > I made sure the card is not sharing an IRQ, I checked the hard drive > and all is well. I load zttool and get the following: > > > > cat /proc/zaptel/* > > Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1" > > > > 1 WCTDM/0/0 > > 2 WCTDM/0/1 > > 3 WCTDM/0/2 > > 4 WCTDM/0/3 > > > > Any suggestions? > > > > Ed > > > > ------------------------------------------------------------------------ > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >_______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Yes, I did. Still nothing. Ed -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Francesco Francesconi Sent: Friday, October 06, 2006 10:23 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] No Dialtone Did you set immediate=no in zapata.conf? Francesco Eddie Johnson Jr wrote:> > > > Hello, > > > > I have the following setup: > > > > 1. Ubuntu Dapper Server 6.06 plus latest patches > > > > 2. Asterisk 1.2.11 > > > > 3. libpri 1.2.3 > > > > 4. Zaptel 1.2.8 > > > > 5. Digium TDM22 (TDM400P) > > > > 6. Analog phone plugged in port 3 > > > > 7. The wctdm, zaptel modules load at startup, I type asterisk as root and > > it is activated. > > > > 8. I check the Channel Map and I have the following: > > > > > > Channel map: > > > > Channel 01: FXO Kewlstart (Default) (Slaves: 01) > > Channel 02: FXO Kewlstart (Default) (Slaves: 02) > > Channel 03: FXS Kewlstart (Default) (Slaves: 03) > > Channel 04: FXS Kewlstart (Default) (Slaves: 04) > > > > 4 channels configured. > > > > I can ssh into the server and remotely connect to the server. Great! > The card is not connected to an outside line as of yet but I have no > dialtone on the phone. I spoke with a rep. at digium and was told a > dialtone should be there. > > > > Zaptel.conf : > > > > > > loadzone=us > > defaultzone=us > > fxoks=1,2 > > fxsks=3,4 > > > > Zapata.conf: > > > > ;FXS Modules > > signalling=fxo_ks > > channel => 1,2 > > ; > > ;FXO Modules > > signalling=fxs_ks > > channel => 3,4 > > > > I made sure the card is not sharing an IRQ, I checked the hard drive > and all is well. I load zttool and get the following: > > > > cat /proc/zaptel/* > > Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1" > > > > 1 WCTDM/0/0 > > 2 WCTDM/0/1 > > 3 WCTDM/0/2 > > 4 WCTDM/0/3 > > > > Any suggestions? > > > > Ed > > > > ------------------------------------------------------------------------ > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >_______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users