Hi All. I have installed Asterisk on linux Redhat version 9, I follow step by ssstep the installation, my card digium is TDM400P, whith modprobe wcfxs I have load this module. My vonfiguration files are in /etc/asterisk, the file /etc/zaptel.conf hace the folloeing lines: fxoks=1 #fxsks=4 loadzone=us defaultzone=us whit command ztcfg -vv say: Zaptel Configuration =====================Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) 1 channels configured. Nut when I start the asterisk the following message appear" Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: manager.c:1478 in init_manager: Unable to open management configuration manager.conf. Call management disabled. Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: chan_agent.c:809 in read_agent_config: No agent configuration found -- agent support disabled Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: chan_mgcp.c:3948 in reload_config: Unable to load config mgcp.conf, MGCP disabled Apr 28 10:54:53 localhost asterisk[2557]: ERROR[2557]: chan_iax2.c:6839 in set_config: Unable to load config iax.conf Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: iax2-provision.c:496 in iax_provision_reload: No IAX provisioning configuration found, IAX provisioning disabled. Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: chan_skinny.c:2541 in reload_config: Unable to load config skinny.conf, Skinny disabled Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: chan_oss.c:1016 in load_module: XXX I don't work right with non-full duplex sound cards XXX Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: chan_oss.c:257 in sound_thread: Read error on sound device: Resource temporarily unavailable Apr 28 10:54:53 localhost asterisk[2557]: ERROR[2557]: chan_zap.c:6220 in mkintf: Signalling requested is FXS Kewlstart but line is in FXO Kewlstart signalling Apr 28 10:54:53 localhost asterisk[2557]: ERROR[2557]: chan_zap.c:9155 in setup_zap: Unable to register channel '1' Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: loader.c:345 in ast_load_resource: chan_zap.so: load_module failed, returning -1 Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: loader.c:440 in load_modules: Loading module chan_zap.so failed! Somebody can give me suggestions? Thanks in Advanced, Regards. _________________________________________________________________ Don't just search. Find. Check out the new MSN Search! http://search.msn.click-url.com/go/onm00200636ave/direct/01/
did you do the following service zaptel stop service zaptel start then run asterisk...
On Thu, 28 Apr 2005 16:01:44 +0000 "Luz Lopez" <viaris@hotmail.com> wrote:> Hi All. > > I have installed Asterisk on linux Redhat version 9, I >follow step by ssstep the installation, my card digium is >TDM400P, whith modprobe wcfxs I have load this module. > > My vonfiguration files are in /etc/asterisk, the file >/etc/zaptel.conf hace the folloeing lines: > fxoks=1 > #fxsks=4 > loadzone=us > defaultzone=us > > whit command ztcfg -vv say: > > Zaptel Configuration > =====================> Channel map: > Channel 01: FXO Kewlstart (Default) (Slaves: 01) > 1 channels configured. > > > Nut when I start the asterisk the following message >appear" > > Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: >manager.c:1478 in init_manager: Unable to open management >configuration manager.conf. Call management disabled. > Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: >chan_agent.c:809 in read_agent_config: No agent >configuration found -- agent support disabled > Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: >chan_mgcp.c:3948 in reload_config: Unable to load config >mgcp.conf, MGCP disabled > Apr 28 10:54:53 localhost asterisk[2557]: ERROR[2557]: >chan_iax2.c:6839 in set_config: Unable to load config >iax.conf > Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: >iax2-provision.c:496 in iax_provision_reload: No IAX >provisioning configuration found, IAX provisioning >disabled. > Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: >chan_skinny.c:2541 in reload_config: Unable to load >config skinny.conf, Skinny disabled > Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: >chan_oss.c:1016 in load_module: XXX I don't work right >with non-full duplex sound cards XXX > Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: >chan_oss.c:257 in sound_thread: Read error on sound >device: Resource temporarily unavailable > Apr 28 10:54:53 localhost asterisk[2557]: ERROR[2557]: >chan_zap.c:6220 in mkintf: Signalling requested is FXS >Kewlstart but line is in FXO Kewlstart signalling > Apr 28 10:54:53 localhost asterisk[2557]: ERROR[2557]: >chan_zap.c:9155 in setup_zap: Unable to register channel >'1' > Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: >loader.c:345 in ast_load_resource: chan_zap.so: >load_module failed, returning -1 > Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: >loader.c:440 in load_modules: Loading module chan_zap.so >failed! > > Somebody can give me suggestions? > > Thanks in Advanced, > > Regards. >Did you put the correct settings in zapata.conf as per the wiki?? http://www.voip-info.org/wiki-Asterisk+config+zapata.conf
You need to change the line type in either your zapata.conf or your zaptel.conf they need to match. ----- Original Message ----- From: "Luz Lopez" <viaris@hotmail.com> To: <asterisk-users@lists.digium.com> Sent: Thursday, April 28, 2005 11:01 AM Subject: [Asterisk-Users] start asterisk> Hi All. > > I have installed Asterisk on linux Redhat version 9, I follow step by > ssstep the installation, my card digium is TDM400P, whith modprobe wcfxs I > have load this module. > > My vonfiguration files are in /etc/asterisk, the file /etc/zaptel.conf > hace the folloeing lines: > fxoks=1 > #fxsks=4 > loadzone=us > defaultzone=us > > whit command ztcfg -vv say: > > Zaptel Configuration > =====================> Channel map: > Channel 01: FXO Kewlstart (Default) (Slaves: 01) > 1 channels configured. > > > Nut when I start the asterisk the following message appear" > > Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: manager.c:1478 in > init_manager: Unable to open management configuration manager.conf. Call > management disabled. > Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: chan_agent.c:809 > in read_agent_config: No agent configuration found -- agent support > disabled > Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: chan_mgcp.c:3948 > in reload_config: Unable to load config mgcp.conf, MGCP disabled > Apr 28 10:54:53 localhost asterisk[2557]: ERROR[2557]: chan_iax2.c:6839 in > set_config: Unable to load config iax.conf > Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: > iax2-provision.c:496 in iax_provision_reload: No IAX provisioning > configuration found, IAX provisioning disabled. > Apr 28 10:54:53 localhost asterisk[2557]: NOTICE[2557]: chan_skinny.c:2541 > in reload_config: Unable to load config skinny.conf, Skinny disabled > Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: chan_oss.c:1016 > in load_module: XXX I don't work right with non-full duplex sound cards > XXX > Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: chan_oss.c:257 in > sound_thread: Read error on sound device: Resource temporarily unavailable > Apr 28 10:54:53 localhost asterisk[2557]: ERROR[2557]: chan_zap.c:6220 in > mkintf: Signalling requested is FXS Kewlstart but line is in FXO Kewlstart > signalling > Apr 28 10:54:53 localhost asterisk[2557]: ERROR[2557]: chan_zap.c:9155 in > setup_zap: Unable to register channel '1' > Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: loader.c:345 in > ast_load_resource: chan_zap.so: load_module failed, returning -1 > Apr 28 10:54:53 localhost asterisk[2557]: WARNING[2557]: loader.c:440 in > load_modules: Loading module chan_zap.so failed! > > Somebody can give me suggestions? > > Thanks in Advanced, > > Regards. > > _________________________________________________________________ > Don't just search. Find. Check out the new MSN Search! > http://search.msn.click-url.com/go/onm00200636ave/direct/01/ > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users
Asterisk Users / Asterisk Biz List Members, About a week ago I cross-posted a message titled "Large Asterisk Setup (~500 Concurrent Calls + Scalability)" to Asterisk-Users and Asterisk-Biz. For reference, the threads generated by that message are archived at the following locations: http://lists.digium.com/pipermail/asterisk-users/2005-April/102823.html http://lists.digium.com/pipermail/asterisk-biz/2005-April/004590.html First, I would like to thank you all for your excellent suggestions and contributions. My misunderstanding of the Digium quad-span card's scaling limitations was corrected (PCI bus traffic is not the problem, it is the number of interrupts generated by the Zaptel drivers) and I was directed to replace the Asterisk Slave Servers in this diagram (http://home.comcast.net/~mroth01/LargeAsteriskSetup.gif) with a VoIP gateway. Following up on that suggestion, I began researching T-1 time division multiplexing in order to understand where the DSP load on an Asterisk server originates and the best options for purchasing a VoIP gateway to offload that processing onto. The results of that research can be found at the following links: T-1 Multiplexing - PSTN Side (http://home.comcast.net/~mroth01/T1-PSTN.gif) T-1 Multiplexing - CPE Side (http://home.comcast.net/~mroth01/T1-CPE.gif) Basic T-1 Time Division Multiplexer (http://home.comcast.net/~mroth01/T1-TDM.gif) Telephony Glossary (http://home.comcast.net/~mroth01/telephony-glossary.html) Sources (http://home.comcast.net/~mroth01/sources.html) My understanding of the T-1 TDM and the PSTN side is pretty solid, as it is mainly based off of Intel Corporation's T1/E1 Technology Primer (see Sources), but the CPE side is largely deduced from what I knew about the PSTN side. There may be holes or mistakes, so I would appreciate any corrections or additions that you can offer. Specifically, I would like a detail of the TDM - VoIP conversion process, similar to the basic T-1 TDM one I provided. The differences between a T-1, DS-1, and ISDN are subtle and not universally agreed upon. For a discussion of these issues see the following links: What's the diff between a T1 and a DS1 (http://pbxtech.info/showthread.php?t=1100) PRI setup (http://pbxtech.info/showthread.php?t=1250) In closing, I have a few questions: - Is my understanding of using the same codecs and signaling protocols on both sides of the Asterisk server in order to circumvent transcoding and conversions on the server correct? - Are there any other host-intensive processes that I should consider offloading to the gateway, such as echo cancellation? - What does the PCM ?-law codec used in T-1 multiplexing map to in terms of Asterisk codecs (G.711 ?-law, perhaps)? - What codec does the Monitor application use when digitally recording calls (if possible, I would like to avoid transcoding the streams when recording and let sox handle the conversions on a different box)? Thank you for your time, Matthew Roth http://voip-info.org/tiki-index.php?page=Running%20Asterisk%20on%20Debian