similar to: Problem with a TDM-400P

I am trying to reconfigure an asterisk box that was using an HFC-S card with bristuff but is now using 2 analog lines therefore I want to use the TDM02B to connect to two POTS lines. The TDM02B has 2 red modules. I have this in /etc/zaptel.conf loadzone=nl defaultzone=nl fxsks=1-2 I have /etc/asterisk/zapata.conf signalling=fxs_ks echocancel=yes echocancelwhenbridged=yes echotraining=400

Hi, I'm just starting out with Asterisk, in combination with a TDM400, filled with 2 FXS on channels 1 and 2, and 1 FXO on 4. Having just started, all I want right now is to be able to answer incoming calls on a phone connected to channel 1. The trouble is the caller id. I have caller id enabled on my line, my phone supports it, and when I connect the phone directly to the line, it works.

Dear All I have a problem with a TDM400 card with 4 x FXS modules. The card carries extensions only and there are no incoming lines. I can make a call to the extension on this card with no problems. However, when I try and call out I just get a busy signal. I also get an error message (as shown at the bottom). Is this a problem? Configs below: [root at asterisk etc]# more zaptel.conf

Howdy, 1 x TDM400P card with 1 x fxo module. 1 x BT Pots line. Location - UK Calls work fine outbound but i'm unable to pickup the inbound calls. Asterisk debug: Asterisk -vvvvvvvvvvcg *CLI> -- Starting simple switch on 'Zap/1-1' -- Executing Wait("Zap/1-1", "1") in new stack -- Executing Answer("Zap/1-1", "") in new stack

Feel free to hit me with a cluestick; maybe it will jar something lose... I'm running a stock *@home 0.6 install and after four days of excrutiatingly annoying debugging, I finally came across the obvious problem. The zaptel driver is reading /etc/zaptel.conf; which by default configures one FXS Kewlstart channel. Asterisk, according to "full" log, will see the first channel, then

I've followed the recent thread on caller id with UK British Telecom networks (where the caller id data is delivered before the first ring). My understanding is that if I use a recent CVS head (e.g. CVS-HEAD-09/18/04-17:45:52) and a TDM400 with FXO modules, all I need to do is include the line: usecallerid=uk In my zapata.conf (in the [channels] section) I've done this, but I get: Sep

Hello I just installed a TE110P in a Dell Poweredge 750 (rackmount), which is connected via crossover T1 cable to a adit 600. Anyway, I've encountered an array of errors, which I believe I have narrowed down to the 22 IRQ misses I encounter on zttool. I've noticed that the te110p and the usb device share an IRQ. Could that be the source of my woes? Would disabling the usb device in the

Hi, I have connected a TDM400P to my asterisk, I have enabled DTMF CID, the data is arriving to the asterisk but asterisk isn't interpretating it: its my full log: 1. Mar 10 16:26:03] DEBUG[8715] dsp.c: dsp busy pattern set to 0,0 2. [Mar 10 16:26:03] VERBOSE[9274] logger.c: -- Starting simple switch on 'Zap/4-1' 3. [Mar 10 16:26:03] VERBOSE[9274]

Hello list. I have a question about how to read the incoming calls' callerid on an FXO interface of a TDM 400 analog card; (it's one of those RED modules). Now -may this is the complexity adding step..- I have a GSM gateway attached to this FXO thing; incoming calls are processed as they should. But both when peeking on the CLI, as well as in the phone display I do not see the caller id.

Everyone, Im sure you've seen this error a million times, but Ive looked everywhere I can think of & still haven't found a solution that works. I'm trying to make an outside call, I can call the physical phone from a xlite on another pc (and vice versa) but whenever I try to make a call to the outside world, this happens: on the CLI: Jun 15 08:45:20 NOTICE[10390]:

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

My outgoing FXO calls are answered but have no audio in either direction if I have callprogress=no in chan_dahdi.conf. If I change to callprogress=yes then the audio returns. My chan_dahdi.conf file is listed below. Can anyone point-out why callprogress=no isn't working? #cat /tmp/a [trunkgroups] [channels] language=en context=incoming toneduration=40 ;usedistinctiveringdetection=yes

hi, i have problem with pass-through faxing with this scenario hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.2.X(xen virtual) - linksys ATA i can fax to fax2mail on hylafax but after upgrade asterisk2 to 1.4 faxing is not working hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.4.X(xen virtual) - linksys ATA configuration is same do you hava any idea what is

Hi, I have Asterisk 1.4.18 and I have been running call center queues on it. Today it suddenly stopped adding inbound calls to queues. I am facing with following error: app_queue.c:3939 queue_exec: unable to join queue "myqueue" In extension file: Queue(myqueue|t|||120) And my agents are joining in following

Hello... I have a big problem with asterisk. Every time i make a call asterisk does not bridge the zap channels. The zap channel from which i'm calling remains in state:ring and applicaton:dial and the zap channel with the external line configured remains in state:dialling an Application:AppDial. Zap/20-1 agentie s 1 Dialing AppDial (Outgoing Line) 09399 (None) Zap/9-1 int_omg 09399 5 Ring

Hi, We have got a new PRI card at one of our Office locations and now I need to install the the device on a remote server. Is there any way to know if the device is loaded already. When I give " cat /proc/zaptel/* " it returns the following. # cat /proc/zaptel/* Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) B8ZS/ESF RED IRQ misses: 2 1 WCT1/0/1

i belong to india. i am making pbx using sangoma fxo card. i want that when ever call comes to my PSTN line i should see the no from where call is coming. so i have to configures chan_dahdi.conf according to my region. i checked dahdi.conf and in that they have mentioned for india

<font size="2">I've got an odd situation where callerid is only picked up every other call.&nbsp; Is there anything I can do so callerid works on all calls?<br><br>I'm seeing the channel hangs up during a call<br><br>&nbsp; == Starting post polarity CID detection on channel 4<br>&nbsp;&nbsp;&nbsp; -- Starting simple switch

HI, im having problem with callerid. Im using tdm2400P and i get this from asterisk logs -- Starting simple switch on 'Zap/4-1' [Mar 24 02:07:48] ERROR[2358]: callerid.c:564 callerid_feed: fsk_serie made mylen < 0 (-1) [Mar 24 02:07:48] WARNING[2358]: chan_zap.c:6416 ss_thread: CallerID feed failed: Success [Mar 24 02:07:48] WARNING[2358]: chan_zap.c:6516 ss_thread: CallerID