similar to: Is Asterisk ready for "real" use?

Hi all, I'm looking for recommendations on ethernet switches for a new install. Ideally would want switches with at least 24 ports, ideally with a GE uplink, and that support PoE (power over ethernet) on every port. I've seen lots of switches, and lots of "power hubs", but the combination, which makes a lot of sense, seems rare. What is out there? Do the switches need to be

Hi all, While pondering my choices for local dial tone service via a bunch of POTS lines or a T1, I began to wonder if perhaps there is another way. Are there VoIP dialtone providers? That is, could I use only my internet connection for voice calls and not have a separate T1/POTS bank for that? I guess I am imagining a company that gateways between the PTSN and the internet backbone.

Hi all, This is a NEWBIE question, so all you experienced types that are tired of stupid questions can move on... I've pretty much given up trying to do my entire phone system over IP (including local service), so I have to select and provision my local CO lines. I need about 10-12 lines which can be POTS lines, of course. But, I thought, why not get something digital and expandable

Hi all, To solve my need for dial in modems, I've hit upon an idea: buy a used T1 "analog" modem bank like a Lucent Portmaster that takes in a T1 and provides several 56K modems. This is overkill for a lightly used dial in service, but the prices of these boxes is so cheap (~$300) with ISPs going away from dial in service that it makes sense. This is how I imagine it would work:

hi everyone, Is it possible to serially connect my panasonic KX-TD1232 with a Linux box(Asterisk installed) and have it working? -- P. K. kakarizz@fastmail.fm

Hi all, I like to have a dial in modem on my toll free number so that when I or my employees travel, they can always get in for net access to read email if no better method is available. Right now, my Panasonic KX-TD1232D PBX receives the call on a POTS line and routes it to an analog modem. The speeds achieved are around 24 kbps due to the digitization of the KX-TD1232D introducing

Hi all, I would be most grateful if someone would review my plans for my new phone system and comment on areas of expected trouble and advice on what to do better. Instead of moving our Panasonic KX-TD1232/TVS200 system (ugh...) to our new location, we've decided to jump into IP telephony with *. But we are new to * (but not Linux), so we're trying to learn as much as we can before we

If Someone did that, How I connect extensions.conf with this type of Hybrid system to work with asterisk inside this schema: PSTN--->PANASONIC KX <------> Asterisk | |--------->send internal call Thanks.

Anyone have any luck with connecting Asterisk to the Panasonic KX-TD500. I have Asterisk connected via crossover to the TE110P. We are able to make internal calls into the Asterisk Box but the PBX vendor (I know nothing about the KX-TD500) tells us it is not possible route DID over the trunk. I find this hard to believe. Anyone have any luck with this? Thanks! -------------- next part

Hello, I want to use Asterisk PBX in front of my old, legacy PBX. The legacy PBX can be outfitted with caller-ID and is already able to handle Calling Party Control Signal Detection (this is a Panasonic KX-TD1232 Super Hybrid PBX. My question is how would one enable Asterisk to control the TDM400P/FXS port to provide to the /FXO CO port on the legacy PBX, support for proper answer supervision/CPC

Hi all, There is someone with some experience interconnecting a Panasonic digital PBX (KX-TD1232) with Asterisk? Thank you and best regards, Dan

Hello We have around 50 phones in our company, and I am playing with the thought to gradually go over to using sip services and ip-phones internally. However at first I would liked the Asterisk just to sit between the phone line and the Panaosnic, so I can take out one lin/number at a time to use ip phones. I am new to Asterisk, and haven't done much configuring of the PBX either. So I also

Hi. I've searched the archives and found nothing regarding collaborating Asterisk with a Panasonic PBX (TD1232 to be exact) Here's my question: Can I use a Wildcard X100P to connect an outgoing line jack (on the Panasonic) to Asterisk, so I can route calls from the PBX to Asterisk, and calls from Asterisk to the PBX? On the hardware page for the X100P card is says it's great for

Does anyone know if it is possible to use the following disconnect tone setting with an x100p card? Disconnect Tone: 350@-19,440@-19;4(.25/.25/1+2) This tone was written for a Sipura SPA-3000 for a Panasonic KX-TD1232. The Panasonic does not support disconnect supervision, so this tone is the only thing that will detect a disconnect. It is not a standard fast busy or offhook tone.

Hello, I ftp'ed the binary RPM for samba from us6.samba.org, and when I tried to verify it, rpm said that MD5 was NOT OK. Has anyone else reported this behavior? Thanks, Hiten Sonpal sonpal@ciholas.com Engineer, CIHOLAS Enterprises Voice: 812 476 2721 x 102 2626 Kotter Ave, Unit #D Fax: 812 476 2881 Evansville, IN 47715 http://www.ciholas.com

Hey folks, I have a Digium TE205P working as a man in the middle: PRI line -------- Asterisk/TE205P -------- PBX The PBX is a Panasonic KX - TVP 100. Everything is working great except for one little issue. Asterisk isn't hanging up the PRI B channel when the PBX channel is hung up. I don't want to overload you with information but please ask if more is needed. I suspect I'm

Sorry if I post in this forum, this may be not the right one, but I hope to find in here some experts which could help me out. I have in one location 8 extensions from a Panasonic PBX ?KX-TD1232? connected to FXO Ports on an MultiVoIP Gateway from Multitech. On the other location I have 8 SP5100 IP-Phones from Micronet as remote extensions. Between the locations I have a VPN.

Roberto Could you provide more details about Panasonic PBX test? model unit and configuration details? Best regards Mc GRATH Ricardo E-Mail mcgrathr at mail2web.com

I'm running into some errors I can't figure out. Situation: I have a Sparc IPX (2.6 Solaris), a Mac OS X box and an Ultra Sparc 1 running Solaris 9. I am trying to rsync a web site between the IPX and Ultra 1. All boxes are running 2.5.5 rsync built from source. Problem: Can't get a a sync between the IPX -> Ultra. IPX = kashmir Ultra = vortac Mac = archer Assumptions: a).

I have 6 domain controllers that were running samba-tng using openldap, Six months ago I converted one of the controllers to Samba3.0.20 and exported my ldap information to be compatible with Samba, every works fine. Specifically I could change passwords at the local windows machine. Two weeks ago I converted my other 5 controllers to Samba3.0.21b everything works except changing passwords at