similar to: Dialing using X100P

I need help creating a channel for my phone device (Quicknet PhoneJack). I have installed and loaded the driver and phone devices listen in /dev (phone0 - phone15). [phone.conf] mode=dialtone format=slinear device => /dev/phone0 fxoks=2 ;Quicknet PhoneJack [extensions.conf] ... exten=>_NXXNXXXXXX,1,Dial,Phone/phone0 ... When I try to make a call, I get the following output: Executing

First, here's what I want to do / what I have: X100P and a Quicknet PhoneJack. I want to be able to pick up the analog phone (connected to the phonejack) and dial another computer (with the same hardware) or just make a regular phone call which will be decided by asterisk depending on the phone number dialed. I know that this won't be taking full advantage of asterisk, but I'm

Hi all, I am still confused about the way to use asterisk with QuickNet Phonejack. If I am not wrong, The phonejack card should be using the phone.conf as the asterisk channel. I was initially confused with the ZAP channel (The digium card), now that I have found out that Phonejack should use the Linux Telephony Devices and its configuration file is phone.conf, but the question is I do not know

Hi, I have recently discovered the project along with the PhoneJacks produced by quicknet, they could be the answer to something I have been looking into. I would like to be able to test using a dial-in server & possibily also a Windows RAS server, however I only have 1 phone line. I was thinking that I create a setup like that illustrated below to solve the problem:- Ext 1000

I'm having a problem defining my channels Here is my zapata.conf ----------------------------------------------------------------------------------------------------- ; Zapata telephony interface ; ; Configuration file [channels] ; rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes

Hi Friends, I am new to linux and new to asterisk. I need some help setting up asterisk in my linux box. Does anyone have a step by step guide ? On my PC i have installed a phonejack (from Quicknet) as well. Your help is appreciated.. I kind lost.. thanks, _________________________________________________________________ Expand your wine savvy — and get some great new recipes — at MSN Wine.

no matter which way I have my /etc/zaptel.cfg this only started happening after a yesterdays CVS update to my zaptel source... Line 1: fxoks=1 Line 2: fxsks=2 Line 23: loadzone=us Line 28: defaultzone=us <End of File> Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) 2 channels

Hi list, I have some problems to get the QuickNet Internet PhoneJack working. What .conf files do I have to edit to get a dialtone for the first test with the standard configs from asterisk? I have the ixj driver running and a cat /proc/ixj after asterisk start tells me one reader and one writer. But if I pick up the receiver I don't get a dialtone nor I'm able to dial a number.

Hi, I just got my TDM400P card (2 modules) and i installed it no probs. The card is detected fine, but for some reason when I add the card to zaptel.conf i get the following error: --snip-- ZT_CHANCONFIG failed on channel 2: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? --snip-- My /etc/zaptel.conf looks

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

Sorry, if this question has been asked before. I have redhat 9 and asterisk installed. I would like to know how can i make work the phonejack with asterisk.

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

Hello. Well I finally rx'd my dev kit (new batch of TDM's apparently. I'm on Mandrake 9.1 There were no hardware install instructions, it would have been nice to know whether the 4-way power connector was to be used or was for some other future or expansion purpose. It came with a floppy disc, no label and it wasn't even write protected. The only readme file was

Hi, I am a newbie in asterisk, i could compile it and run it with no problem on a RedHat 9. In the same box, i got a linejack and a phonejack cards and i downloaded the CVS driver from quicknet. This 2 card were working in a openh323 (openphone and pstn) project with gnugk on a RedHat 9. I am using the default samples, and i tried /dev/phone0 and /dev/phone1, but when i run asterisk, i get this

How will this fare? I am planning on putting an asterisk box for my brother in the Philippines but they only have dialup internet. I want them to be able to use a telephone set on a phonejack or linejack card and call me and vice versa via VOIP. My setup in the US is working already with a broadband cable connection. I am thinking that dialup may not work because of the bandwidth required

Hi, Would someone assist me with the configuration of my TMD10B and X100P cards? I would ask Digium but my support was good for only one install...( I had to rebuild my * box). I wrote down the configuration but I must have made a mistake somewhere. I have followed the instructions on the Digium site but I must be missing something. Here's the config (snippets) I've been attempting to

Perhaps this will help... I have a phone connected to a QuickNet PhoneJack card. When I pick it up, I get a dial tone. When I dial a certain number of digits, the call is processed by Asterisk. The question: How does Asterisk determine how many numbers to let me dial? I'm banging my head against the desk here... _9XXXXXXX lets me make an outbound call, but _9X. only lets me dial 9 plus

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the

[root@server ~]# modprobe zaptel [root@server ~]# modprobe wcfxo ZT_CHANCONFIG failed on channel 1: No such device or address (6) FATAL: Error running install command for wcfxo [root@server ~]# ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address