Hello,
I have problems rebuilding RAID1 array. The bios shows status 'Rebuild'
and 'Volumes with "Rebuild" status will be rebuilt within the
operating
system'.
When I try to do 'atacontrol rebuild ar0':
atacontrol: ioctl(IOCATARAIDREBUILD): Device not configured
I run 6.2-STABLE:
dmesg:
...
atapci1: <Intel ICH8 SATA300 controller> port
0xec00-0xec07,0xe880-0xe883,0xe800-0xe807,0xe480-0xe483,0xe400-0xe41f
mem 0xfebff800-0xfebfffff irq 19 at device 31.2 on pci0
atapci1: AHCI Version 01.10 controller with 6 ports detected
ata5: <ATA channel 0> on atapci1
ata6: <ATA channel 1> on atapci1
ata7: <ATA channel 2> on atapci1
ata8: <ATA channel 3> on atapci1
ata9: <ATA channel 4> on atapci1
ata10: <ATA channel 5> on atapci1
...
ad10: 152627MB <Seagate ST3160811AS 3.AAE> at ata5-master SATA300
ad12: 152627MB <Seagate ST3160811AS 3.AAE> at ata6-master SATA300
ar0: 152625MB <Intel MatrixRAID RAID1> status: READY
ar0: disk0 READY (master) using ad10 at ata5-master
ar0: disk1 READY (mirror) using ad12 at ata6-master
pciconf -lv:
atapci1@pci0:31:2: class=0x010400 card=0x81ec1043 chip=0x28228086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
class = mass storage
subclass = RAID
atacontrol status ar0:
ar0: ATA RAID1 subdisks: ad10 ad12 status: READY
The motherboard is Asus P5-E.
How to rebuild my RAID?
Thanks in advance
Hi I personally would say its a major mistake to use these pseudo-hardware controllers. I really recommend you either use software-raid via gvinum or buy a true full-capable hardware raid controller. cheers Krassimir Slavchev wrote:> Hello, > > I have problems rebuilding RAID1 array. The bios shows status > 'Rebuild' and 'Volumes with "Rebuild" status will be rebuilt within > the operating system'. > When I try to do 'atacontrol rebuild ar0': > atacontrol: ioctl(IOCATARAIDREBUILD): Device not configured > > I run 6.2-STABLE: > > dmesg: > ... > atapci1: <Intel ICH8 SATA300 controller> port > 0xec00-0xec07,0xe880-0xe883,0xe800-0xe807,0xe480-0xe483,0xe400-0xe41f > mem 0xfebff800-0xfebfffff irq 19 at device 31.2 on pci0 > atapci1: AHCI Version 01.10 controller with 6 ports detected > ata5: <ATA channel 0> on atapci1 > ata6: <ATA channel 1> on atapci1 > ata7: <ATA channel 2> on atapci1 > ata8: <ATA channel 3> on atapci1 > ata9: <ATA channel 4> on atapci1 > ata10: <ATA channel 5> on atapci1 > ... > ad10: 152627MB <Seagate ST3160811AS 3.AAE> at ata5-master SATA300 > ad12: 152627MB <Seagate ST3160811AS 3.AAE> at ata6-master SATA300 > ar0: 152625MB <Intel MatrixRAID RAID1> status: READY > ar0: disk0 READY (master) using ad10 at ata5-master > ar0: disk1 READY (mirror) using ad12 at ata6-master > > pciconf -lv: > atapci1@pci0:31:2: class=0x010400 card=0x81ec1043 chip=0x28228086 > rev=0x02 hdr=0x00 > vendor = 'Intel Corporation' > class = mass storage > subclass = RAID > > atacontrol status ar0: > ar0: ATA RAID1 subdisks: ad10 ad12 status: READY > > The motherboard is Asus P5-E. > > > How to rebuild my RAID? > > Thanks in advance > > > _______________________________________________ > freebsd-stable@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org" > > > >-- Georg 'Therion' Bege http://coruscant.info http://www.ninth-art.de therion@ninth-art.de <therion at ninth minus art dot de> GnuPG-Key-ID: 0x5717E214 FingerPrint: A8EC B4B2 C9A9 483B CC87 56EE 07A1 C78E 5717 E214 !DSPAM:465172ad25448062420477!
Hi, On 21 May 2007, at 10:07, Krassimir Slavchev wrote:> Hello, > > I have problems rebuilding RAID1 array. The bios shows status > 'Rebuild' and 'Volumes with "Rebuild" status will be rebuilt within > the operating system'. > When I try to do 'atacontrol rebuild ar0': > atacontrol: ioctl(IOCATARAIDREBUILD): Device not configuredFrom the output below, assuming the system is running OK, the RAID doesn't need rebuilding. The BIOS is just confused about the state of the array, it will probably still boot from it OK. [I've got a system with Intel ESB2 in the same state, anyone who knows how to make the BIOS see sense (short of a full rebuild) please tell.]> I run 6.2-STABLE: > > dmesg: > ... > atapci1: <Intel ICH8 SATA300 controller> port > 0xec00-0xec07,0xe880-0xe883,0xe800-0xe807,0xe480-0xe483,0xe400-0xe41f > mem 0xfebff800-0xfebfffff irq 19 at device 31.2 on pci0 > atapci1: AHCI Version 01.10 controller with 6 ports detected > ata5: <ATA channel 0> on atapci1 > ata6: <ATA channel 1> on atapci1 > ata7: <ATA channel 2> on atapci1 > ata8: <ATA channel 3> on atapci1 > ata9: <ATA channel 4> on atapci1 > ata10: <ATA channel 5> on atapci1 > ... > ad10: 152627MB <Seagate ST3160811AS 3.AAE> at ata5-master SATA300 > ad12: 152627MB <Seagate ST3160811AS 3.AAE> at ata6-master SATA300 > ar0: 152625MB <Intel MatrixRAID RAID1> status: READY > ar0: disk0 READY (master) using ad10 at ata5-master > ar0: disk1 READY (mirror) using ad12 at ata6-master > > pciconf -lv: > atapci1@pci0:31:2: class=0x010400 card=0x81ec1043 > chip=0x28228086 rev=0x02 hdr=0x00 > vendor = 'Intel Corporation' > class = mass storage > subclass = RAID > > atacontrol status ar0: > ar0: ATA RAID1 subdisks: ad10 ad12 status: READY > > The motherboard is Asus P5-E. > > > How to rebuild my RAID? > > Thanks in advance > > > _______________________________________________ > freebsd-stable@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to "freebsd-stable- > unsubscribe@freebsd.org" >-- Bob Bishop +44 (0)118 940 1243 rb@gid.co.uk fax +44 (0)118 940 1295