I'm a long time reader of this list but this is my first post. I sincerely
hope I have done my homework properly before resorting to bother you all.
Equipment:
Fujitsu-Siemens laptop model C-6175
3Com Megahertz 10/100 CardBus NIC model 3CXFE575CT (xl driver)
Problem:
NIC doesn't initialize correctly with ACPI enabled. It works perfectly if I
disable ACPI at boot time. I've tested with GENERIC kernel on 5.4-RELEASE,
6.1-BETA4 and HEAD - same behaviour with all three versions.
Googling turns up many posts with similar or identical error messages on
various pieces of hardware but I can find no solution.
I've enabled the following debug options in loader.conf:
hw.pccard.debug=1
hw.cbb.debug=1
hw.cardbus.debug=1
hw.cardbus.cis_debug=1
Complete dmesgs with ACPI enabled, with ACPI disabled and with "boot
-v" are
attached but snip with relevant error messages is copied below for
convenience. Any suggestions would be higly appreciated.
Thanks
Morgan
cbb0: <TI1420 PCI-CardBus Bridge> at device 4.0 on pci0
cbb0: Found memory at 80000000
cbb0: Secondary bus is 0
cbb0: Secondary bus set to 2 subbus 3
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <TI1420 PCI-CardBus Bridge> at device 4.1 on pci0
cbb1: Found memory at 80001000
cbb1: Secondary bus is 0
cbb1: Secondary bus set to 4 subbus 5
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
Status is 0x30000006
Status is 0x30000820
cbb1: card inserted: event=0x00000000, state=30000820
cbb1: cbb_power: 3V
TUPLE: LINKTARGET [3]: 43 49 53
Manufacturer ID: 01015752
TUPLE: Unknown(0x04) [6]: 03 01 00 00 00 00
TUPLE: Unknown(0x05) [13]: 41 9a 01 b5 1e 01 b5 1e 02 30 ff ff 01
cardbus1: Opening BAR: type=IO, bar=10, len=0100
Product version: 5.0
Product name: 3Com Corporation | 3CCFE575CT | LAN Cardbus Card | 004 |
Functions: Network Adaptor, Memory
CIS reading done
cardbus1: Resource not specified in CIS: id=14, size=80
cardbus1: Resource not specified in CIS: id=18, size=80
cardbus1: Non-prefetchable memory at 88000000-880000ff
cbb alloc res fail
cardbus1: Can't get memory for IO ports
xl0: <3Com 3c575C Fast Etherlink XL> port 0-0xff mem
0x88000000-0x8800007f,0x88001000-0x8800107f at device 0.0 on cardbus1
cbb alloc res fail
xl0: couldn't map ports/memory
device_attach: xl0 attach returned 6
cbb1: cbb_power: 0V
-------------- next part --------------
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-BETA4 #0: Tue Mar 14 13:59:38 UTC 2006
root@wv1u.samsco.home:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Celeron (497.56-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 201261056 (191 MB)
avail memory = 187408384 (178 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <FUJ IRIS> on motherboard
acpi0: Power Button (fixed)
acpi_ec0: <Embedded Controller: GPE 0x9> port 0x62,0x66 on acpi0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem
0xe0000000-0xe3ffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
cbb0: <TI1420 PCI-CardBus Bridge> at device 4.0 on pci0
cbb0: Found memory at 80000000
cbb0: Secondary bus is 0
cbb0: Secondary bus set to 2 subbus 3
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <TI1420 PCI-CardBus Bridge> at device 4.1 on pci0
cbb1: Found memory at 80001000
cbb1: Secondary bus is 0
cbb1: Secondary bus set to 4 subbus 5
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1040-0x104f at device 7.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1060-0x107f irq 9
at device 7.2 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge> at device 7.3 (no driver attached)
pci0: <multimedia, audio> at device 8.0 (no driver attached)
pci0: <simple comms> at device 16.0 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model GlidePoint, device ID 0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 drq 1
on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
sio1 port 0x2e8-0x2ef irq 3 drq 3 on acpi0
sio1: type 16550A
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ugen0: vendor 0x0a12 product 0x0001, rev 1.10/8.28, addr 2
Timecounter "TSC" frequency 497558472 Hz quality 800
Timecounters tick every 1.000 msec
Status is 0x30000006
Status is 0x30000820
cbb1: card inserted: event=0x00000000, state=30000820
cbb1: cbb_power: 3V
TUPLE: LINKTARGET [3]: 43 49 53
Manufacturer ID: 01015752
TUPLE: Unknown(0x04) [6]: 03 01 00 00 00 00
TUPLE: Unknown(0x05) [13]: 41 9a 01 b5 1e 01 b5 1e 02 30 ff ff 01
cardbus1: Opening BAR: type=IO, bar=10, len=0100
Product version: 5.0
Product name: 3Com Corporation | 3CCFE575CT | LAN Cardbus Card | 004 |
Functions: Network Adaptor, Memory
CIS reading done
cardbus1: Resource not specified in CIS: id=14, size=80
cardbus1: Resource not specified in CIS: id=18, size=80
cardbus1: Non-prefetchable memory at 88000000-880000ff
cbb alloc res fail
cardbus1: Can't get memory for IO ports
xl0: <3Com 3c575C Fast Etherlink XL> port 0-0xff mem
0x88000000-0x8800007f,0x88001000-0x8800107f at device 0.0 on cardbus1
cbb alloc res fail
xl0: couldn't map ports/memory
device_attach: xl0 attach returned 6
cbb1: cbb_power: 0V
ad0: 5729MB <FUJITSU MHK2060AT D836> at ata0-master UDMA33
acd0: CDROM <CD-224E/1.7A> at ata1-master UDMA33
Trying to mount root from ufs:/dev/ad0s1a
-------------- next part --------------
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-BETA4 #0: Tue Mar 14 13:59:38 UTC 2006
root@wv1u.samsco.home:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Celeron (497.56-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 201261056 (191 MB)
avail memory = 187424768 (178 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
cpu0 on motherboard
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 7 Entries> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem
0xe0000000-0xe3ffffff at device 0.0 on pci0
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
cbb0: <TI1420 PCI-CardBus Bridge> at device 4.0 on pci0
cbb0: Found memory at 80000000
cbb0: Secondary bus is 0
cbb0: Secondary bus set to 2 subbus 3
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <TI1420 PCI-CardBus Bridge> at device 4.1 on pci0
cbb1: Found memory at 80001000
cbb1: Secondary bus is 0
cbb1: Secondary bus set to 4 subbus 5
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1040-0x104f at device 7.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1060-0x107f irq 9
at device 7.2 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge> at device 7.3 (no driver attached)
pci0: <multimedia, audio> at device 8.0 (no driver attached)
pci0: <simple comms> at device 16.0 (no driver attached)
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model GlidePoint, device ID 0
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
on isa0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
sio4: <NSC6001> at port 0x2e8-0x2ef irq 3 drq 3 on isa0
sio4: type 16550A
unknown: <PNP0401> can't assign resources (port)
psmcpnp0: irq resource info is missing; assuming irq 12
unknown: <PNP0700> can't assign resources (port)
ugen0: vendor 0x0a12 product 0x0001, rev 1.10/8.28, addr 2
Timecounter "TSC" frequency 497559755 Hz quality 800
Timecounters tick every 1.000 msec
Status is 0x30000006
Status is 0x30000820
cbb1: card inserted: event=0x00000000, state=30000820
cbb1: cbb_power: 3V
TUPLE: LINKTARGET [3]: 43 49 53
Manufacturer ID: 01015752
TUPLE: Unknown(0x04) [6]: 03 01 00 00 00 00
TUPLE: Unknown(0x05) [13]: 41 9a 01 b5 1e 01 b5 1e 02 30 ff ff 01
cardbus1: Opening BAR: type=IO, bar=10, len=0100
Product version: 5.0
Product name: 3Com Corporation | 3CCFE575CT | LAN Cardbus Card | 004 |
Functions: Network Adaptor, Memory
CIS reading done
cardbus1: Resource not specified in CIS: id=14, size=80
cardbus1: Resource not specified in CIS: id=18, size=80
cardbus1: Non-prefetchable memory at 88000000-880000ff
cardbus1: IO port at 1100-11ff
xl0: <3Com 3c575C Fast Etherlink XL> port 0x1100-0x11ff mem
0x88000000-0x8800007f,0x88001000-0x8800107f irq 10 at device 0.0 on cardbus1
miibus0: <MII bus> on xl0
tdkphy0: <TDK 78Q2120 media interface> on miibus0
tdkphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 00:04:76:f6:4f:d8
ad0: 5729MB <FUJITSU MHK2060AT D836> at ata0-master UDMA33
acd0: CDROM <CD-224E/1.7A> at ata1-master UDMA33
Trying to mount root from ufs:/dev/ad0s1a
-------------- next part --------------
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-BETA4 #0: Tue Mar 14 13:59:38 UTC 2006
root@wv1u.samsco.home:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0aa2000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0aa216c.
Calibrating clock(s) ... i8254 clock: 1193073 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 497559648 Hz
CPU: Intel Celeron (497.56-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 201261056 (191 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c25000 - 0x000000000bc57fff, 184758272 bytes (45107 pages)
avail memory = 187408384 (178 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f63a0
bios32: Entry = 0xfd8a6 (c00fd8a6) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xfd890+0x134
pnpbios: Found PnP BIOS data at 0xc00f63d0
pnpbios: Entry = f0000:aa9f Rev = 1.0
Other BIOS signatures found:
wlan: <802.11 Link Layer>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <FUJ IRIS> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003904
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
pcibios: BIOS version 2.10
Found $PIR table, 7 entries at 0xc00fdf50
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 7 D 0x63 9 10 11
embedded 0 4 A 0x60 10 11
embedded 0 8 A 0x62 5 7 9 10
slot 1 0 16 A 0x61 9
slot 2 0 17 A 0x63 9
embedded 0 1 A 0x61 9 10 11
embedded 1 0 A 0x61 9 10 11
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 4 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 4 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 4 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 16 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 17 func 0
acpi0: Power Button (fixed)
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 5 9 10 11
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 5 9 10 11
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 9 10 11
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 9 N 0 5 9 10 11
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 9 N 0 5 9 10 11
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 9 10 11
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 5 9 10 11
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 5 N 0 5 9 10 11
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 9 10 11
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 9 N 0 5 9 10 11
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 9 N 0 5 9 10 11
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 9 10 11
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 0 func 0
acpi_ec0: <Embedded Controller: GPE 0x9> port 0x62,0x66 on acpi0
acpi_ec0: info: new max delay is 140 us
acpi_ec0: info: new max delay is 270 us
acpi_ec0: info: new max delay is 280 us
acpi_ec0: info: new max delay is 310 us
acpi_ec0: info: new max delay is 380 us
acpi_ec0: info: new max delay is 11000 us
ACPI timer: 0/4 0/5 0/5 0/5 0/5 0/5 0/4 0/5 0/4 0/5 -> 0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x1010
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.7.INTD at func 2: 9
ACPI: Found matching pin for 0.4.INTA at func 0: 255
ACPI: Found matching pin for 0.4.INTA at func 1: 255
ACPI: Found matching pin for 0.8.INTA at func 0: 5
ACPI: Found matching pin for 0.16.INTA at func 0: 9
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x7190, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 3, range 32, base e0000000, size 26, enabled
found-> vendor=0x8086, dev=0x7191, revid=0x03
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x001f, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x80 (3840 ns), mingnt=0x8c (35000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x104c, dev=0xac51, revid=0x00
bus=0, slot=4, func=0
class=06-07-00, hdrtype=0x02, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns)
intpin=a, irq=255
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base 00000000, size 12, enabled
found-> vendor=0x104c, dev=0xac51, revid=0x00
bus=0, slot=4, func=1
class=06-07-00, hdrtype=0x02, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns)
intpin=a, irq=255
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base 00000000, size 12, enabled
found-> vendor=0x8086, dev=0x7110, revid=0x02
bus=0, slot=7, func=0
class=06-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7111, revid=0x01
bus=0, slot=7, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 00001040, size 4, enabled
found-> vendor=0x8086, dev=0x7112, revid=0x01
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=9
map[20]: type 4, range 32, base 00001060, size 5, port disabled
pcib0: matched entry for 0.7.INTD (src \\_SB_.LNKD:0)
pcib0: slot 7 INTD routed to irq 9 via \\_SB_.LNKD
found-> vendor=0x8086, dev=0x7113, revid=0x03
bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[90]: type 4, range 32, base 0000ff80, size 4, enabled
found-> vendor=0x1013, dev=0x6005, revid=0x01
bus=0, slot=8, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x18 (6000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fc010000, size 12, enabled
map[14]: type 1, range 32, base fc000000, size 16, enabled
pcib0: matched entry for 0.8.INTA (src \\_SB_.LNKC:0)
pcib0: slot 8 INTA routed to irq 5 via \\_SB_.LNKC
found-> vendor=0x11c1, dev=0x0450, revid=0x00
bus=0, slot=16, func=0
class=07-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xfc (63000 ns), maxlat=0x0e (3500 ns)
intpin=a, irq=9
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base fc011000, size 8, memory disabled
map[14]: type 4, range 32, base 00001050, size 3, port disabled
map[18]: type 4, range 32, base 00001400, size 8, enabled
pcib0: matched entry for 0.16.INTA (src \\_SB_.LNKB:0)
pcib0: slot 16 INTA routed to irq 9 via \\_SB_.LNKB
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem
0xe0000000-0xe3ffffff at device 0.0 on pci0
agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xe0000000
agp0: allocating GATT for aperture of size 64M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0x2000-0x2fff
pcib1: memory decode 0xfc100000-0xfdffffff
pcib1: prefetched decode 0xfff00000-0xfffff
ACPI: Found matching pin for 1.0.INTA at func 0: 9
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x1002, dev=0x4c4d, revid=0x64
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fd000000, size 24, enabled
pcib1: (null) requested memory range 0xfd000000-0xfdffffff: good
map[14]: type 4, range 32, base 00002000, size 8, enabled
pcib1: (null) requested I/O range 0x2000-0x20ff: in range
map[18]: type 1, range 32, base fc100000, size 12, enabled
pcib1: (null) requested memory range 0xfc100000-0xfc100fff: good
pcib1: matched entry for 1.0.INTA (src \\_SB_.LNKB:0)
pcib1: slot 0 INTA routed to irq 9 via \\_SB_.LNKB
pci1: <display, VGA> at device 0.0 (no driver attached)
cbb0: <TI1420 PCI-CardBus Bridge> at device 4.0 on pci0
cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x80000000
cbb0: Found memory at 80000000
cbb0: Secondary bus is 0
cbb0: Secondary bus set to 2 subbus 3
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib0: matched entry for 0.4.INTA (src \\_SB_.LNKA:0)
pcib0: slot 4 INTA routed to irq 11 via \\_SB_.LNKA
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
0x00: 0xac51104c 0x02100007 0x06070000 0x00824008
0x10: 0x80000000 0x020000a0 0x20030200 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc
0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b
0x40: 0x109510cf 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x20649061 0x00000000 0x00000000 0x01cc1d22
0x90: 0x606602c0 0x00000000 0x00000000 0x00000000
0xa0: 0xfe110001 0x00c00000 0x00000815 0x0000000b
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
cbb1: <TI1420 PCI-CardBus Bridge> at device 4.1 on pci0
cbb1: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x80001000
cbb1: Found memory at 80001000
cbb1: Secondary bus is 0
cbb1: Secondary bus set to 4 subbus 5
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib0: matched entry for 0.4.INTA (src \\_SB_.LNKA:0)
pcib0: slot 4 INTA routed to irq 11 via \\_SB_.LNKA
cbb1: [MPSAFE]
cbb1: PCI Configuration space:
0x00: 0xac51104c 0x02100007 0x06070000 0x00824008
0x10: 0x80001000 0x020000a0 0x20050400 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc
0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b
0x40: 0x109510cf 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x20649061 0x00000000 0x00000000 0x01cc1d22
0x90: 0x606602c0 0x00000000 0x00000000 0x00000000
0xa0: 0xfe110001 0x00c00000 0x00000815 0x0000000b
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
PCI-ISA bridge with incorrect subclass 0x80
PCI-ISA bridge with incorrect subclass 0x80
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1040-0x104f at device 7.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1040
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=01
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x01 err=0x04 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=00 stat1=01 devices=0x4<ATAPI_MASTER>
ata1: [MPSAFE]
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1060-0x107f irq 9
at device 7.2 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1060
uhci0: [GIANT-LOCKED]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge> at device 7.3 (no driver attached)
pci0: <multimedia, audio> at device 8.0 (no driver attached)
pci0: <simple comms> at device 16.0 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model GlidePoint, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
ppc0: using extended I/O port range
ppc0: ECP SPP SPP
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 drq 1
on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0: irq maps: 0x201 0x211 0x201 0x201
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
sio1: irq maps: 0x201 0x209 0x201 0x201
sio1 port 0x2e8-0x2ef irq 3 drq 3 on acpi0
sio1: type 16550A
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
acpi0
fdc0: ic_type 90 part_id 73
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ex_isa_identify()
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
ugen0: vendor 0x0a12 product 0x0001, rev 1.10/8.28, addr 2
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 497559648 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
battery0: battery initialization start
Status is 0x30000006
Status is 0x30000820
cbb1: card inserted: event=0x00000000, state=30000820
cbb1: cbb_power: 3V
TUPLE: LINKTARGET [3]: 43 49 53
Manufacturer ID: 01015752
TUPLE: Unknown(0x04) [6]: 03 01 00 00 00 00
TUPLE: Unknown(0x05) [13]: 41 9a 01 b5 1e 01 b5 1e 02 30 ff ff 01
cardbus1: Opening BAR: type=IO, bar=10, len=0100
Product version: 5.0
Product name: 3Com Corporation | 3CCFE575CT | LAN Cardbus Card | 004 |
Functions: Network Adaptor, Memory
CIS reading done
cardbus1: Resource not specified in CIS: id=14, size=80
cardbus1: Resource not specified in CIS: id=18, size=80
cardbus1: Non-prefetchable memory at 88000000-880000ff
cbb alloc res fail
cardbus1: Can't get memory for IO ports
found-> vendor=0x10b7, dev=0x5257, revid=0x10
bus=4, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0xa8 (5040 ns), mingnt=0x0a (2500 ns), maxlat=0x05 (1250 ns)
intpin=a, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
xl0: <3Com 3c575C Fast Etherlink XL> port 0-0xff mem
0x88000000-0x8800007f,0x88001000-0x8800107f at device 0.0 on cardbus1
cbb alloc res fail
xl0: couldn't map ports/memory
device_attach: xl0 attach returned 6
cbb1: cbb_power: 0V
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=80 wire
ad0: setting PIO4 on PIIX4 chip
ad0: setting UDMA33 on PIIX4 chip
battery0: battery initialization done, tried 1 times
ad0: 5729MB <FUJITSU MHK2060AT D836> at ata0-master UDMA33
ad0: 11733120 sectors [12416C/15H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad0
ad0: Intel check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: setting PIO4 on PIIX4 chip
acd0: setting UDMA33 on PIIX4 chip
acd0: <CD-224E/1.7A> CDROM drive at ata1 as master
acd0: read 4134KB/s (4134KB/s), 128KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ATA PseudoRAID loaded
Trying to mount root from ufs:/dev/ad0s1a
start_init: trying /sbin/init