Hi all I am trying to configure an E100P channel bank card. The * will be connected to a PSTN switch with an E1 line. I am a bit confused with signaling table of E100P Digium Cards. The signaling table of E100P Digium cards is each 64K channel's ABCD bits which indicate the state for transmit signaling. My problem now is where to find the CAS(Channel Associated Signalling) signaling ABCD bit table ? (TxABCD, RxABCD) How can I modify the ABCD value ? Thanks for your help. These are my system info: [zaptel.conf] # E100P card span=1,0,0,cas,hdb3,crc4 fxoks=1-12 unused=13-15 unused=17-31 # # Wildcard X100P card fxsks=32 defaultzone=us loadzone=us [zapata.conf] [channels] musiconhold=default signalling=fxo_ks echocancel=yes echocancelwhenbridged=yes echotraining=400 callerid=asreceived context=default channel => 1-12 language=en signalling=fxs_ks channel => 32 Output of zttool: - Alarms Span OK Digium Wildcard E100P E1/PRA Card 0 OK Wildcard X101P Board 1 Current Alarms: No alarms. Sync Source: Internally clocked IRQ Misses: 0 Bipolar Viol: 0 Tx/Rx Levels: 0/ 0 Total/Conf/Act: 31/ 12/ 0 1111111111222222222333 1234567890123456789012345789012 TxA 000000000000 TxB 111111111111 TxC 000000000000 TxD 111111111111 RxA 000000000000 RxB 000000000000 RxC 111111111111 RxD 000000000000 - [root at GW /]# lsmod Module Size Used by Not tainted wcfxo 9376 0 (unused) wct1xxp 13184 0 (unused) zaptel 179168 0 [wcfxo wct1xxp] [root at GW /]# cat /proc/interrupts CPU0 0: 68392 XT-PIC timer 1: 4 XT-PIC keyboard 2: 0 XT-PIC cascade 3: 453361 XT-PIC wcfxo 5: 1048 XT-PIC eth0 8: 1 XT-PIC rtc 9: 0 XT-PIC usb-ohci, usb-ohci, ehci-hcd 10: 415190 XT-PIC t1xxp 12: 32 XT-PIC PS/2 Mouse 14: 5257 XT-PIC ide0 15: 0 XT-PIC ide1 NMI: 0 ERR: 0 [root at GW /]# cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3//CRC4 1 WCT1/0/1 FXOKS 2 WCT1/0/2 FXOKS ... 11 WCT1/0/11 FXOKS 12 WCT1/0/12 FXOKS -- James Lin
Peter Svensson
2005-May-02 22:54 UTC
[Asterisk-Users] signaling table of E100P Digium Cards
On Tue, 3 May 2005, James Lin wrote:> I am trying to configure an E100P channel bank card. > > The * will be connected to a PSTN switch with an E1 line. > > I am a bit confused with signaling table of E100P Digium Cards. > > The signaling table of E100P Digium cards is each 64K channel's ABCD > bits which indicate the state for transmit signaling. > > My problem now is where to find the CAS(Channel Associated Signalling) > signaling ABCD bit table ? (TxABCD, RxABCD) > > How can I modify the ABCD value ?For CAS on an E1 you need MFC/R2 support. See http://www.soft-switch.org/unicall/installing-mfcr2.html. Peter