Displaying 12 results from an estimated 12 matches similar to: "cox regression warning/error messages"
2008 Nov 29
0
Error in check(itp) : object does not represent a K sample problem with censored data
Hello,
I have two questions regarding a survival analysis I have been
working on. Below is the code to date.
The variables:
1) recidivism$intDaysUntilFVPO are the number of days before an
violent offence was committed - if no offence was committed than the
days between court hearing and end of data collection was recorded.
2) recidivism$intDaysUntilFNVPO are the number of days before a
2009 Mar 14
1
obtaining the values for the hazard function in a cox regression
Hello ,
I am hoping for some advice regarding obtaining the values for the
hazard function in a cox regression that I have undertaken. I have a
model in the following form, analysed with the package survival (v.
2.34-1) and a log-log plot obtained using Design (v. 2.1-2).
For two variables, the lines in the survival curves crossed. The
statistician I been obtaining advice from (who does not
2009 Mar 16
0
hazard function in a Cox model
-- begin included message ---
I am hoping for some advice regarding obtaining the values for the
hazard function in a cox regression that I have undertaken. I have a
model in the following form, analysed with the package survival (v.
2.34-1) and a log-log plot obtained using Design (v. 2.1-2).
For two variables, the lines in the survival curves crossed. The
statistician I been obtaining
2009 Mar 28
1
stratified variables in a cox regression
>Hello,
I am hoping for assistance in regards to examining the contribution
of stratified variables in a cox regression. A previous post by Terry
Therneau noted that "That is the point of a strata; you are declaring
a variable to NOT be proportional hazards, and thus there is no
single "hazard ratio" that describes it". Given this purpose of
stratification, in the
2016 Dec 10
0
Success with Broadcom installation
Wanted to report success, following this procedure:
https://wiki.centos.org/HowTos/Laptops/Wireless/Broadcom
At the bottom, I see something of a compatibility matrix, but a line
representing my specific setup does not exists. So I offer the following
data to show that it works in my environment.
[erik at localhost ~]$ uname -r
3.10.0-327.36.3.el7.x86_64
[erik at localhost ~]$ cat
2013 Oct 31
7
[Bug 870] New: Iptables cannot block outbound packets sent by Nessus
https://bugzilla.netfilter.org/show_bug.cgi?id=870
Summary: Iptables cannot block outbound packets sent by Nessus
Product: iptables
Version: 1.4.x
Platform: x86_64
OS/Version: Ubuntu
Status: NEW
Severity: normal
Priority: P5
Component: iptables
AssignedTo: netfilter-buglog at lists.netfilter.org
2012 Nov 29
5
bootstrapped cox regression (rms package)
Hi,
I am trying to convert a colleague from using SPSS to R, but am having
trouble generating a result that is similar enough to a bootstrapped cox
regression analysis that was run in SPSS. I tried unsuccessfully with
bootcens, but have had some success with the bootcov function in the rms
package, which at least generates confidence intervals similar to what is
observed in SPSS. However, the
2013 Jan 16
1
rombios unable to loaded MPT BIOS
Hi All,
When tried to pass through 2 mpt2sas HBA to hvm guest, hvmloader
paused with below:
MPT BIOS Fault 09h encountered at adapter PCI(00h,04h,00h)
Press any key to continue...
Checked related codes and mostly like it caused by rombios did not
loaded MPT BIOS properly, and lead MPT BIOS failed to bootup.
config-file of the guest as below:
----------------------------------
# cat vm.cfg
2012 Nov 29
0
bootstrapped cox regression in rms package (non html!)
Hi,
I am trying to convert a colleague from using SPSS to R, but am having
trouble generating a result that is similar enough to a bootstrapped
cox regression analysis that was run in SPSS. I tried unsuccessfully
with bootcens, but have had some success with the bootcov function in
the rms package, which at least generates confidence intervals similar
to what is observed in SPSS. However, the
2004 Dec 20
3
Problems with loading TE110 module
Hello!
I discovered, that I'm unable to load ther kernel module under 2.4.28.
Before that I had 2.4.26 and tryed to upgrade the kernel to 2.4.28.
After restart (reboot - soft restart) I can't load the module. When I
go back to 2.4.26 and try to load the module, I'm getting the same
problem.
Only turning off/on helps. What can I do? It's very annoying because
the box is in hosting
2004 Dec 29
18
No response on port 80 with Shorewall
I have problem getting answer on http request from all my local subnets
but not from local subnet.
Ping and requests on ports 21 22 23 25 110 works fine.
I logged port 80 in rules files and I got
accept entry same for local subnet and other subnets.
Local subnet is 192.168.6
Dec 29 09:52:40 zinfsrv2 kernel: Shorewall:loc2fw:ACCEPT:IN=eth0 OUT=
MAC=00:09:6b:07:ca:cc:00:10:b5:fa:bd:71:08:00