similar to: shipro.test

X-BeenThere: r-help at stat.math.ethz.ch X-Mailman-Version: 2.1.5 Precedence: list Reply-To: korponai.janos at nyuduvizig.hu List-Id: "Main R Mailing List: Primary help" <r-help.stat.math.ethz.ch> List-Unsubscribe: <https://www.stat.math.ethz.ch/mailman/listinfo/r-help>, <mailto:r-help-request at stat.math.ethz.ch?subject=unsubscribe> List-Archive:

I am using R 1.9.1 with R Commander GUI under Windows at work, and under Linux Mandrake 10 OR at home. I am having no problems running R Commander under windows. Under Linux, though, the opening and sometimes closing of windows from R Commander produces identical and repetitive error messages (in dialogue boxes and mirrored in the console): >"Warning: X11 protocol error: BadWindow

Dear List! I installed R and quite a few packages I use. When I try to start BiodiversityR the library loads without any problems but GUI do not start. Rcmdr loads without any problems. I am using R 2.13.0 64 bit. Downgrade to R 2.12.2 works. Thanks, Janos

In this dialplan, the SIP user agent is a Sipura two line adapter with line 1 as SIP ID "1000" and line 2 as SIP ID "2000". Basically I have this set up so that 1000 and 2000 are "lines in hunting" on incoming extension "555". I want an incoming call to try to ring ext. 1000, if 1000 is busy, then ring 2000, if 2000 is also busy than ring Voicemail. Here

I'm trying to use the FollowMe app with Asterisk 1.4.17. I've followed the WIKI page on setting it up but I can't seem to get it to work. Here is my Asterisk version: pbx1*CLI> core show version Asterisk 1.4.17 built by root @ pbx1 on a i686 running Linux on 2008-01-10 12:08:48 UTC Here is a log of when the FollowMe is being called: NOTE: I've tried to use the AstDB as

I have an asterisk Redhat 9 box running 4 hardphone extensions. Inter-extension calls are crystal clear. However when I dial out through my iconnect account I get a lot of jitter. At first I thought it was my nat gateway but after I programmed on of the hardphones (budge tone 100) for direct dial to iconnect I have clear voice transmission. I have no way of explaining this. My asterisk sip.conf

Hi The shapiro.test function outputs a value of the W statistic, which should be 1 if the distribution is normal, and a p-value for the test (as the documentation states). I'm a bit confused with some results. I'm getting a W=0.9977 and a p-value=0.1889. I was expecting that a W of 0.9977 would tell me that the distribution is normal so p-value should be small ... What am I missing ?

I have a setup of 3 Cisco 7940 running Sip image 6.3. All these phone are registered by the below information *CLI> sip show peers Name/username Host Mask Port Status 2002/2002 192.168.22.199 (D) 255.255.255.255 5060 Unmonitored 2001/2001 192.168.22.200 (D) 255.255.255.255 5060 Unmonitored 2000/2000 192.168.22.198 (D)

I feel I'm on the verge of setting up a pbx for handling internal calls only... The last problem - I think - I've run into is w/ the phone registration running asterisk -vvvc I get a bunch of messages looking like so Apr 6 14:46:05 NOTICE[1116957488]: chan_sip.c:5623 handle_request: Registration from 'sip:2001@192.168.22.254' failed for '192.168.22.1' Apr 6

Hi guys! Im new there, and i havent found yet stories about uplink bandwith limits, and i would like to limit my Exim''s speed, coz its eating my ADSL''s whole uplink. Til now i used the #:~ tc qdisc add dev ppp0 root tbf rate 50kbit latency 50ms burst 1540 command, buts its limiting the whole link:/ I checked the documents on that link:

Hi! How can I access to the Controller from a Layered web service? Cow

Hi! I try to use a layered webservice and I want to get back an array of users; In the API I use: api_method :listUsers,:returns=>[[User]] in the service: def listUsers User.find(:all) end Result in soap mode: Don''t know how to cast TrueClass to Object Result in XML-RPC mode: You have a nil object when you didn''t expect it! You might have expected

Hi! The last 2 day''s I tried create WebService which get back ActiveRecord object, but it''s always get back error. Today I found why. In Mysql the boolean type is a int(1) alias, but in postgresql the boolean type is boolean(!). When in the database table contain boolean type the AWS going to crazy because it''s can''t recognize it. (It''s say:

Hello everyone, First time on this list, because I can't seem to find anything about my problem. I hope someone here will be able to help me. I have a file and print server running an old Ubuntu 7.04 x86 and Samba 3.0.2.4 that came with it. (I tried upgrading samba once, but it kept crashing, so I went back to this default version, because it works very well.) The problem is, as the title

Dear Members, I would like to share my success story with a scheduled samba4 upgrade. Our faculty domain contains one dc and two fileserver, plus the pc labor windows machines(7 room * 25 machines). We use debian on the servers and installed samba4 from stable backports. Experiences: * i could successfully apply the samdb.py and user.py pathces from Rowland Penny. After that, the user creation

Dear Members, Today i upgraded my small domain which ran on debian 7 to debian 8. The samba version does not change, it stays at 4.1.17 After the upgrade i noticed, that the ssh password auth does not work on the member servers. Excerpt from the log: Aug 18 14:46:31 medea winbindd[707]: STATUS=daemon 'winbindd' finished starting up and ready to serve

Hi, I have a problem with Samba. I use Samba 4.1.17 (because my company's security policy deny Samba upgrade) on Debian. I created a Samba Active Directory Domain Cotroller with linux.local and a Windows Active Directory Domain Controller with windows.local domain (I used Windows Server 2012 R2). I am need to create a smb share in Linux and autheticate users from windows.local domain and need