similar to: Is PCI-Passthrough supported in Linux 2.4 domU kernel?

Hi list, The crux of my setup is given in the Subject: field. I''m using Xen 3.0.3 (release) on a VIA Nehemiah chipset with Linux 2.6.16.29 in both dom0 and domU. Because the documentation on PCI passthrough is a bit sparse, I''m turning to the mailing list.. hopefully you guys have some input. My goal is to set up a system where: * 1 domU VM runs at a time. * The VM can be

Fixed : Double amount of memory from 128 to 256 and iommu works it out fine. RTFEM (read the fucking error message) : [ 0.872160] Kernel panic - not syncing: Out of memory and no killable processes... ________________________________________________________________________________________________________________ Frédéric Abel| RTS France BeNeLux | Quantum Corporation

Hi, is it possible to use a vga controller in domU via pci passthrough? What''s about nvidia/ati kernel modules? I tried to hide a ati radeon 9200 in dom0 and use it in domU but X fails to start with the following error (seems to be unrelated to the vga hardware): xf86OpenConsole: Cannot open /dev/tty0 (No such file or directory) Thanks & Regards Daniel

Hello, my dom0 is an alpinelinux installed with kernel 3.10.14-1-grsec and xen 4.2.2. My domU is an opensuse 12.3 with all patches installed. The system works great, but when I do only switch xen from 4.2.2 to 4.3.0 (packages from http://nl.alpinelinux.org/alpine/edge/main/x86_64/) then my kernel in the domU does an Oops and the drivers for my dvb card aren''t loaded successfully. When I

I started a new thread because this not a pv-ops dom0 anymore. I''m running Andrew Lyon''s 2.6.31-4 patches for a non-pv-ops kernel. Got it again, after issuing "poweroff" from the domU. (XEN) (XEN) NMI - MEMORY ERROR (XEN) ----[ Xen-3.5-unstable x86_64 debug=y Not tainted ]---- (XEN) CPU: 0 (XEN) RIP: e008:[<ffff82c48011f55c>] remove_from_heap+0x8f/0xd0

Hi! As dom0 I''m running Ubuntu Hardy withe xen 3.3 from backports. Reason to using xen 3.3 is that I could get Intrepid stock kernel to work as domu with xen 3.2. Now the problem I have is that I can''t passthrough PCI-devices to my domu. If I run lspci in the domu nothing is returned. I''ve tried to use the kernel from Hardy (2.6.24-21-xen) and stock kernel from

Hi all! I want to assign a physical network card (e100) to a domU: I think Dom0 is ok but domU does not recognize the pci nic. into DomU I don''t know wath should I see: I have nothing in dmesg nor in messages... Into Dom0 I have this modules.conf: options pciback hide=(0000:03: 08.0) install e100 /sbin/modprobe pciback; /sbin/modprobe --ignore-install e100 This is dmesg: pciback

testing, uname -ri 2.6.33-rc5-4-xen x86_64 rpm -qa | grep -i Xen-4 xen-4.0.0_20873_01-29.1.x86_64 cat test.cfg name = ''test'' builder = ''linux'' bootloader = ''/usr/lib/xen/boot/domUloader.py'' bootargs = ''--entry=xvda1:vmlinuz-xen,/boot/initrd-xen'' disk = [

I am having problems getting my 64-bit Debian Squeeze (Xen version 4.0, Linux Kernel 2.6.32) dom0 to pass a Gigabyte HD 5450 graphics card to an HVM 64-bit Arch Linux domU. I have two Gigabyte HD 5450 graphics cards connected to my Gigabyte GA-X79-UP4 motherboard. I can pass the secondary card (the one the bios doesn’t show up on) to an HVM 32-bit Windows XP domU (I thought that would be the hard

Hi, I have a perfectly running Xen 3.0.4 installation with kernel 2.6.16-42 with PCI passthrough for my internet interface (ethernet). But with I boot my 2.6.19 xen kernel on dom0, I''m unable to have the NIC working in domU. I can see the NIC both in domU and dom0 with lspci. All other network interfaces are working correctly (ethernet in dom0 and bridges). Here is my entry in grub

Hi, Not trying to be obnoxious on this list. I thought perhaps phrasing the subject line specific will catch some ones eye (hopefully). Would like some help on 2 issues. 1 - I have PCI pass through working for an Nvidia card which is my 2nd graphics adapter and I wish to dedicate it to a particular domU. I had to mod my initrd as follows; mkinitrd -f --preload=pciback

Hi all, I have a problem with pci passthrough in xen 3.4.0 (Debian Lenny). I need to pass the audio board (which is 00:1b.0) to the domU, so I do the following: - Put pciback.permissive pciback.hide=(00:1b.0) in dom0 kernel boot options - Put swiotlb=force in domU kernel boot options - Put pci = [ ''00:1b.0'' ] in domU config file - reboot the machine I can see in dmesg the

More information... I have pcifront showing as a module in the DomU and the usb shows in dmesg as: [ 3.167543] usbcore: registered new interface driver usbfs [ 3.167563] usbcore: registered new interface driver hub [ 3.167585] usbcore: registered new device driver usb [ 3.196056] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.196060] usb usb1: New USB device strings:

Greetings, I have Xen installation with all domains (dom0+domU) being Debian Lenny. I''d like to pass my usb printer to one of those domU domains. I couldn''t make usb passthrough to work, so I decided that I will pass the whole usb controller to the domU. It didn''t worked either. I have read tons of internet howtos only to find the solutions proposed don''t

Hello, I try to passthrough an usb 1.1 device (floppy drive) to a domU. Dom0 and domU are based on opensuse11.4. I did the follwowing in dom0 --snip-- xenserver:~ # xm usb-list-assignable-devices 3-1 : ID 0644:0000 TEAC TEAC FD-05PUB 3-2 : ID 0644:0000 TEAC TEAC FD-05PUB xenserver:~ # xm usb-hc-create vdrserver 1 2 xenserver:~ # xm usb-list vdrserver Idx BE

Hi : I am trying to do PCIe passthrough on HVM domu. I have window XP as a HVM domu and xen-4.0. dom0 and domU (without device assign) works fine. I have more than one NIC card. I want to passthrough 03:00.0 to domu here are the list of my nic cards: lspci | grep -i eth 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)

On Mar 17, 6:14pm, Howell Tam wrote: } Subject: Re: [Xen-users] Dom0 freeze on HVM DomU Windows reboot with VGA p > Hi all again, Hi, hope the weekend is going well for everyone. > > > have you found a solution for this behaviour? Cause I''m currently > > > seeing a similar result with my installation. > > I''ve been away for a few weeks and

On Mar 17, 6:14pm, Howell Tam wrote: } Subject: Re: [Xen-users] Dom0 freeze on HVM DomU Windows reboot with VGA p > Hi all again, Hi, hope the weekend is going well for everyone. > > > have you found a solution for this behaviour? Cause I''m currently > > > seeing a similar result with my installation. > > I''ve been away for a few weeks and

On Thu, May 12, 2016 at 12:11 PM, Francis Greaves <francis at choughs.net> wrote: > I am running Xen 4.6 on CentOS 7 in a Dell Poweredge T430 > I need PCI Passthrough to get USB working. I am following the Xenproject > Wiki > I have enabled the Virtulasation in the BIOS. > I have xen_pciback as a module > I have issued the command: > > xl pci-assignable-add 00:1a0.0

Florian, I read already here and there that you shall not use shared interrupts in different PV DomUs, although I never found a written statement. But behaviour is exactly as you described, thus I took care that cards that share an IRQ are in the same DomU/Dom0. I also selected my motherboards accordingly. When I lately discussed lately with someone about MSI, I had the hope this could help,