similar to: pciback.hide sundance

I have this cheap "ENCORE 10/100Mbps Fast Ethernet PCI Adapter" which comes with its own driver that compiles to 'sundance.ko' and performs bad (30% packet loss) on a fully updated CentOS 4.4 box. This brand, model and driver have worked OK for me on some other CentOS installations, none of which are 4.4. Short of replacing the board, which you can bet I will do, can anybody

Hi, I have a PC with 3 ethernet interfaces. I am trying to a) assign 2 ethernet interfaces exclusively to one domU by using the late binding method and b) to use a bridge between the third interface and dom0 (that works fine). The goal is to not to have to use bridges for the exclusively assigned interfaces. Is it possible? (If not, no need to read the rest) The problem I have is that I

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Has anyone here had any experience with D-Link's quad-port ethernet NIC, model DFE-580TX ? The people from Mikrotik says it can cause systemwide lockup, but from what I have been reading around, this board seem to work ok. This is the only quad-port NIC I have found with a reasonable price, so I'm seriously considering using it. Comments ?

A Clean Filter is the most important element of clean water, because it filters all the 'dirty-stuff' from the water. Clogged Filters don't work so you need to deep-clean or replace your filter(s) on a regular basis. For more details visit:http://www.spa-daddy.com/

Hello Everyone, I have set up a xen server with 10 physical network devices using the bridge mode of XEN. This is because I want to split and separate the network traffic for security reasons. Maybe the best way is to use pci back hide. But I want to understand what is going on here. For all testings I have only activated eth[0-3]. My first tests were successful. I have created a VM using

Hello everone, I am new to this mailing list. I am regarding problems while trying to load an additional driver module. The module is sundance.o, used for D-Link DFE 550 nics. I downloaded this driver tarball from the D-Links website. I am using Syslinux 1.52 which is based on the 2.4.18 kernel. My syslinux is embedded on three floppy disks and all works pretty well and boots up without any

Hi! I''ve 5 DSL routers and a linux router in a switch. The linux router is doing NAT for a LAN network, but it freezes when I set up load balancing with this command: ip route add default proto static\ nexthop via 192.168.1.10 dev eth1\ nexthop via 192.168.1.20 dev eth1\ nexthop via 192.168.1.30 dev eth1\ nexthop via 192.168.1.40 dev eth1\ nexthop

Is anyone else seeing this: perl @/kern/makeops.pl -h @/opencrypto/crypto_if.m rm -f .depend mkdep -f .depend -a -nostdinc -D_KERNEL -DKLD_MODULE -I- -I. -I@ -I@/../include -I/usr/obj/usr/local/src-STABLE/src/i386/usr/include /usr/local/src-STABLE/src/sys/modules/hifn/../../dev/hifn/hifn7751.c /usr/local/src-STABLE/src/sys/modules/hifn/../../dev/hifn/hifn7751.c:47: opt_hifn.h: No such file or

Hi! >Message: 5 >Date: Thu, 08 Jul 2004 17:00:21 +0530 >From: Sudheer Divakaran <sudheer@svw.com> >To: lartc@mailman.ds9a.nl >Subject: [LARTC] Is Linux based Router feasible > >Hi, > >I''ve a local LAN consisting of about 150 machines. I''m using a Linux >machine as the gateway machine which inturn connects to two different >ISPs. My

Hello I have some problems with 3Com nics, after a upgrade from 5.5-STABLE to 6.4-STABLE. This machine has two 3com nics (one is LAN other is WAN) and i see too much "watchdog timeout" on both cards. This on/off up/down on cards, affect the interrupt to clients that are downloading from apache web server, especially on large files. --------------------------------------------

After updating my kernel from a 4.7-stable to 4.8-stable update, my SB PCI128 is no longer recognized by the pcm driver. Here is my dmesg: FreeBSD 4.8-STABLE #0: Thu Jul 17 14:13:52 CDT 2003 root@hautlos.stout.osu-res.okstate.edu:/usr/obj/usr/src/sys/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: AMD Athlon(tm) Processor (800.03-MHz 686-class CPU) Origin =

Hello, I have this cheap network card which insists on me compiling its own sundance.ko module every time I update my kernel release. I had the poor idea to leave nightly yum service enabled on this remote server, only to find my network was gone at the following reboot. Had to go there, figure out that kernel stuff is carefully avoided by up2date, but not so by yum service, and rebuild. Compiling

On Wed, 2005-12-21 at 15:00 +0100, edd at debian.org wrote: > --CE+1k2dSO48ffgeK > Content-Type: text/plain; charset=us-ascii > Content-Disposition: inline > > Resend after type in mailheader. I have the bug on my system with > yesterday's R 2.2.1. A library mismatch is still a likely cause. > > Dirk <SNIP> > On 21 December 2005 at 01:50, Ethan

I've got a HP dv8000 laptop. Setting up the wpi driver for wireless freezes the system on boot with the following error: wpi0 requested unsupported memory range wpi0: could not allocate memory resource It lists a pcbi device (pcbi4 i think) and an actual memory range, but since I have to reboot using kernel.old the /var/run/dmesg.boot is wiped with the info. Is there anyway to grab the

While doing this on an 80gig ibm ide drive: dd if=/dev/cdrom of=cd.iso I got the following assertian failure Aug 9 14:43:27 budder kernel: Assertion failure in __journal_remove_journal_head() at journal.c:1733: "jh2bh(jh) == bh" Aug 9 14:43:27 budder kernel: kernel BUG at journal.c:1733! Aug 9 14:43:27 budder kernel: invalid operand: 0000 Aug 9 14:43:27 budder kernel: CPU: 0 Aug 9

Hi, It seems that destroying pcifront/pciback always fails on current xen. This patch fixes the problem, making pciback switch to "Closed" state after pcifront switched to "Closing" state. Regards, ------------------- Yosuke Iwamatsu NEC Corporation _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com

--CE+1k2dSO48ffgeK Content-Type: text/plain; charset=us-ascii Content-Disposition: inline Resend after type in mailheader. I have the bug on my system with yesterday's R 2.2.1. A library mismatch is still a likely cause. Dirk -- Hell, there are no rules here - we're trying to accomplish something. -- Thomas A. Edison

I''m using Xen 4.01 and jeremy''s pvops kernel, the kernel version is 2.6.32.18. At first I want to test the performance of pci passthrough when it comes to the network card 82571EB I''m using the Jeremy''s kernel 2.6.32.18 as DomU kernel too. And I found if the interface is not connected, I mean the network card receives no packet, ( the network card

I''m using Xen 4.01 and jeremy''s pvops kernel, the kernel version is 2.6.32.18. At first I want to test the performance of pci passthrough when it comes to the network card 82571EB I''m using the Jeremy''s kernel 2.6.32.18 as DomU kernel too. And I found if the interface is not connected, I mean the network card receives no packet, ( the network card

On Wed, 21 Dec 2005 edd at debian.org wrote: > > --CE+1k2dSO48ffgeK > Content-Type: text/plain; charset=us-ascii > Content-Disposition: inline > > Resend after type in mailheader. I have the bug on my system with > yesterday's R 2.2.1. A library mismatch is still a likely cause. This seems to be a readline 5.1 error. I was unable to reproduce it with 4.3 or 5.0. gdb)