similar to: PCI e Passthrough

Hi: I have two HVM domU ubuntu 10.04 Lts and Window XP running. I have assigned PCIe device to each of this domU. I would like to communicate these two VM. Can anyone give me some idea on how to do. I did some research on IVC but unable to get answer. Anything will be appreciated. Anju _______________________________________________ Xen-users mailing list

Hi:I am stuck here. I want to run two VMs (linux and window) concurrently. When I run them separately one at a time it works fine. But when I do xm create vm1.cfg then the domU starts and again if I do xm create vm2.cfg it just stucked and need to restart it. I am using live cd for vm2. I am guessing I am missing some steps here. I will appreciate your help. Thank you

Hi, I installed 2.0.5 binary release of Xen in my FC3 , and below is my grub.conf ---- part of grub.conf -- title Fedora Core (2.6.10-1.766_FC3) root (hd0,7) kernel /vmlinuz-2.6.10-1.766_FC3 ro root=LABEL=/ rhgb quiet initrd /initrd-2.6.10-1.766_FC3.img title Xen 2.0 / XenLinux 2.6.10 root (hd0,7) kernel /boot/xen.gz dom0_mem=131072 module

I am looking into setting up Xen 4.0 on a simple dual-boot Windows/ubuntu laptop with the following partitions: | Device Boot Start End Blocks Id System | /dev/sda1 * 1 223 1782784 7 HPFS/NTFS | /dev/sda2 223 21713 172624888 7 HPFS/NTFS | /dev/sda3 35854 38914 24576344 7 HPFS/NTFS | /dev/sda4

Hello, I''m having problems with VTD on this board. The board/cpu/bios all support vt-d and I think maybe I''m just missing something? Any feedback would be much appreciated :) Output below: root@vm:~# xm create /etc/xen/vm-nine.cfg Using config file "/etc/xen/vm-nine.cfg". Error: Failed to assign device to IOMMU (0000:05:00.0@100,msitranslate=1,power_mgmt=0)

Hello, I''m having problems with VTD on this board. The board/cpu/bios all support vt-d and I think maybe I''m just missing something? Any feedback would be much appreciated :) Output below: root@vm:~# xm create /etc/xen/vm-nine.cfg Using config file "/etc/xen/vm-nine.cfg". Error: Failed to assign device to IOMMU (0000:05:00.0@100,msitranslate=1,power_mgmt=0)

Hi: recently i am doing fast boot from linux kernel to Xen hypervisor,and vice-versa. it means when linux is running on the real machine, i just want to switch to Xen hypervisor without going through bootloader. both linux and dom0 of Xen using the same filesystem. we boot Xen and the Linux with the following command in grub: title Ubuntu 8.04.2, kernel 2.6.29 root (hd0,7)

Hi! i notice a serious regression with 3.5 as Dom0 kernel (3.4 was rock stable): 1st: only the GPU PCI Passthrough works, the PCI USB Controller is not recognized within the DomU (HVM Win7 64) Dom0 cmdline is: ro root=LABEL=dom0root xen-pciback.hide=(08:00.0)(08:00.1)(00:1d.0)(00:1d.1)(00:1d.2)(00:1d.7) security=apparmor noirqdebug nouveau.msi=1 Only 8:00.0 and 8:00.1 get passed through

With the kernel option ''xen-pciback.hide=(00:14.2) xen-pciback.permissive'', Xen-4.2.0-rc3 is unable to pass through my onboard Intel HDA audio adapter to a Windows7 guest. I tried doing the same in KVM and it worked immediately without issue. On the guest, I get a "High Definition Audio Controller" with the correct vendor/device ID, and an error of "This device

Hello, I am desperately trying to get pci-passthrough to working. I want to pass a tg3 nic to domU. when booting domU I get a lot of messages: pcifront pci-0: pciback not responding!!! in domU, "ifconfig eth... adress up" hangs for 2 minutes, finally ifconfig -a shows a correct setting with no data transmitted rx/tx The IP Adress is being assigned, but there is no data transmission

All, I would like to run the following issue past the list to confirm that my problem analysis makes sense or whether I missed something: We have a HP ML370G6 server with VT-x and VT-d enabled in the BIOS. It is equipped with two Smart Array HBAs - one connected to the HDD array (SmartArray P800) and one connected to an LTO tape drive (SmartArray P212). Both controllers use the same driver

The attached patches allow the pciback module to perform a reset whenever a PCI device is: - attached to the pciback module, as so: echo "0000:01.07.0" > /sys/bus/pci/devices/pciback/bind - detached from the pciback module, as so: echo "0000:01.07.0" > /sys/bus/pci/devices/pciback/unbind - and when the guest is done with (internally when the guest is not using

Hello all, I''m trying to pass my PCI device through to an HVM. I''m following the steps on the xen pci passthrough wiki. First I check my pci devices #lspci - 03:00.0 VGA compatible controller: ATI Technologies Inc Device 671d 03:00.1 Audio device: ATI Technologies Inc Device aa80 04:00.0 Display controller: ATI Technologies Inc Device 671d 04:00.1 Audio device: ATI

So yesterday I got was able to get a domU successfully using a PCI SCSI card. This morning I restarted the host server. When I try to start up the same domU I get this error: Error: pci: improper device assignment specified: pci: 0000:0e:04.0 must be co-assigned to the same guest with 0000:0e:04.0, but it is not owned by pciback. How do I make this card owned by pciback on reboot. Do I need to

testing, uname -ri 2.6.33-rc5-4-xen x86_64 rpm -qa | grep -i Xen-4 xen-4.0.0_20873_01-29.1.x86_64 cat test.cfg name = ''test'' builder = ''linux'' bootloader = ''/usr/lib/xen/boot/domUloader.py'' bootargs = ''--entry=xvda1:vmlinuz-xen,/boot/initrd-xen'' disk = [

Hi, I have successfully start my Win7 x86 domU on my x64 Xen dom0 system. Now I want to give my Win7 full access to my Nvidia card. lspci 01:00.0 VGA compatible controller: NVIDIA Corporation G86 [Quadro NVS 140M] (rev a1) and I added these to my /etc/modprobe.d/xen-pciback.conf options xen-pciback hide=(0000:01:00.0) then I ran modprobe xen-pciback nothing happens on the screen, and my

Hi! I am trying to export a PCI device (an AVM Fritzcard PCI ISDN card...) to a domU but when starting my domU I am getting this error: "pciback pci-4-0: 22 Couldn''t locate PCI device (0000:00:06.0)! perhaps already in-use?" My system is running both debian etch in dom0 and domU... Below you can find (hopefully) all important information... Sincerely, Gaubatz Patrick

Hi All, Please help me. I am now installing the XEN on my PC and trying to config the pci pass through. My motherboard is intel DQ45CB which is vtd enabled. I downloaded the latest xen4.0 source from xen.org which is the latest release. I downloaded stable-2.6.32-x dom0 kernel source from jeremy''s repository. After compiling the xen and dom0 kernel, I could play it. I could create

Hi All, Please help me. I am now installing the XEN on my PC and trying to config the pci pass through. My motherboard is intel DQ45CB which is vtd enabled. I downloaded the latest xen4.0 source from xen.org which is the latest release. I downloaded stable-2.6.32-x dom0 kernel source from jeremy''s repository. After compiling the xen and dom0 kernel, I could play it. I could create

This issue was brought up about a year and a half ago. So I''ll bring it up again and see if anything happens. I''ve got an infiniband network and am attempting to pass the infiniband card through the host and give it to the guest. I''m working with standard CentOS 5.2 on both guest and host with their provided xen (3.0.3 ish). I''ve also attempted to install the