similar to: Supermicro AOC-SAT2-MV8 and 1TB Seagate Barracuda ES.2

I have a supermicro AOC-SAT2-MV8 and am having some issues getting drives to work. From what I can tell, my cables are to long to use with SATA2. I got some drives to work by jumpering them down to sata1, but other drives I can''t jumper without opening the case and voiding the drive warranty. Does anyone know if there is a system setting to drop it back to SATA1? I use zfs on a raid2 if

Bouncing a thread from the device drivers list: http://opensolaris.org/jive/thread.jspa?messageID=357176 Does anybody know if OpenSolaris will support this new Supermicro card, based on the Marvell 88SE6480 chipset? It''s a true PCI Express 8 port JBOD SAS/SATA controller with pricing apparently around $125. If it works with OpenSolaris it sounds pretty much perfect. --------------

I''ve been trying to get either smartctl or sg3_utils to report properly. They both have the same low-level problems which leads me to suspect either I''m doing something wrong OR there is a problem in the marvell88sx / sd / SATA etc framework. I can access drive name/serial number of all drives on the SAT2 card and the temperature is returned from the IE log page on my two

I posted a thread here... http://forums.opensolaris.com/thread.jspa?threadID=596 I am trying to finish building a system and I kind of need to pick working NIC and onboard SATA chipsets (video is not a big deal - I can get a silent PCIe card for that, I already know one which works great) I need 8 onboard SATA. I would prefer Intel CPU. At least one gigabit port. That''s about it. I

On Wed, Jul 9, 2008 at 1:12 PM, Tim <tim at tcsac.net> wrote: > Perfect. Which means good ol'' supermicro would come through :) WOHOO! > > AOC-USAS-L8i > > http://www.supermicro.com/products/accessories/addon/AOC-USAS-L8i.cfm Is this card new? I''m not finding it at the usual places like Newegg, etc. It looks like the LSI SAS3081E-R, but probably at 1/2 the

My test setup of 8 x 2G virtual disks under Virtual Box on top of Mac OS X is running nicely! I haven''t lost a *single* byte of data. ;) A. -- Adam Sherman CTO, Versature Corp. Tel: +1.877.498.3772 x113

Hi all, Sorry for the offtopic question. I hope though that others on this list or reading the archive find the answers useful too. It seems the Adaptec 1405 4port SAS HBA I bought only works with RHEL and SuSE through a closed source driver, and thus is quite useless :-( I was stupid enought to think "Works with RHEL and SuSE" meant "Certified for RHEL and SuSE, but driver in

Hey all, I''m not sure if this is a ZFS bug or a hardware issue I''m having - any pointers would be great! Following contents include: - high-level info about my system - my first thought to debugging this - stack trace - format output - zpool status output - dmesg output High-Level Info About My System --------------------------------------------- - fresh

The standard controller that has been recommended in the past is the AOC-SAT2-MV8 - an 8 port with a marvel chipset. There have been several mentions of LSI based controllers on the mailing lists and I''m wondering about them. One obvious difference is that the Marvel contoller is PCI-X and the LSI controllers are PCI-E. Supermicro have several LSI controllers. AOC-USASLP-L8i with the

Hi all, I am currently planning a new home file server on a gigabit network that will be utilizing ZFS (on SXDE). The files will be shared via samba as I have a mixed OS environment. The controller card I will be using is the SuperMicro SAT2-MV8 133MHz PCI-X card. I have two options for CPUs/motherboards: AMD Athlon64 3000+ (64 bit) DFI LanParty UT 250gb (NForce 3 based) motherboard 32 bit

I have a raidz2 and did a scrub, it took 8h. Then I reconnected some drives to other SATA ports, and now it takes 15h to scrub?? Why is that? -- This message posted from opensolaris.org

I am trying to test a new setup of NV74. I have set up the system with ZFS boot. Everything works fine until I pull a drive. The system locks up when I try to run any command e.g. zpool status. There is no communication with the server from then on. It does not even respond to pings. Setup - Supermicro SC836TQ-R800 Chassis Supermicro X7DB8 Motherboard Supermicro SAT2-MV8 SATA controller

I am bumping this thread because I too have the same question ... can I put modern 3TB disks (hitachi deskstars) into an old x4500 ? If not, would the x4540 accept them ? -- This message posted from opensolaris.org

After having massive problems with a supermicro X7DBE box using AOC-SAT2-MV8 Marvell controllers and opensolaris snv79 (same as described here: http://sunsolve.sun.com/search/document.do?assetkey=1-66-233341-1) we just start over using new hardware and opensolaris 2008.05 upgraded to snv94. We used again a supermicro X7DBE but now with two LSI SAS3081E SAS controllers. And guess what? Now we get

Hello, is there someone who knows if I can use AOC for billing in Asterisk? I mean: let's say I have an external SIP device that produces AOC data. This device connects me to the telco network. Can Asterisk, if connected via SIP with this device, collect AOC data and put it in the CDR records? If not, which is the right way to use AOC for billing? Thanks a lot Stefano Corsi -- Stefano

Hi Firstly apologies for the spam if you got this email via multiple aliases. I''m trying to document a number of common scenarios where ZFS is used as part of the solution such as email server, $homeserver, RDBMS and so forth but taken from real implementations where things worked and equally importantly threw up things that needed to be avoided (even if that was the whole of ZFS!).

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I'd like to know what is the current situation with regard to AOC-E, when Asterisk is inserted between the telco and an existing PBX, using E1 / EuroISDN. Can Asterisk pass the AOC-E information received from the telco to the PBX, so that billing system still works? The system would be for a hotel, so breaking billing system is not possible.

Hello, i have an 8 port sata-controller and i don''t want to spend the money for 8 x 750 GB Sata Disks right now. I''m thinking about an optimal way of building a growing raidz-pool without loosing any data. As far as i know there are two ways to achieve this: - Adding 750 GB Disks from time to time. But this would lead to multiple groups with multiple redundancy/parity disks. I

hi all, I'm trying to send text messages to Snom 300 to show the credit remaining during the call... Sending a MESSAGE directly to the phone via udp i'm able to update the text on the display... but not during the conversation. I read about AOC, but i can't find any documentation about Asterisk + SIP + AOC Have you any experience, docs or workaround to suggest? Thx Ale

> Hello everyone, > > I am trying to find out whether AOC (any of the 3 types) is currently supported by Asterisk and for which hardware combination. > > Does anyone know if? AOC info can be used in the CDR when the interface to the outside world is ISDN BRI (not pri) and the internal counterpart is an analog extension (dahdi, i guess)? What about sip or iax? > > I have found