similar to: Kernel panic on zfs import (hardware failure)

Hi! I have a problem with ZFS and most likely the SATA PCI-X controllers. I run opensolaris 2008.11 snv_98 and my hardware is Sun Netra x4200 M2 with 3 SIL3124 PCI-X with 4 eSATA ports each connected to 3 1U diskchassis which each hold 4 SATA disks manufactured by Seagate model ES.2 (500 and 750) for a total of 12 disks. Every disk has its own eSATA cable connected to the ports on the PCI-X

Hello zfs-discuss, One of a disk started to behave strangely. Apr 11 16:07:42 thumper-9.srv sata: [ID 801593 kern.notice] NOTICE: /pci at 1,0/pci1022,7458 at 3/pci11ab,11ab at 1: Apr 11 16:07:42 thumper-9.srv port 6: device reset Apr 11 16:07:42 thumper-9.srv scsi: [ID 107833 kern.warning] WARNING: /pci at 1,0/pci1022,7458 at 3/pci11ab,11ab at 1/disk at 6,0 (sd27): Apr 11 16:07:42 thumper-9.srv

Greetings all. I am facing serious problems running ZFS on a storage server assembled out of commodity hardware that is supposed to be Solaris compatible. Although I am quite familiar with Linux distros and other unices, I am new to Solaris so any suggestions are highly appreciated. First I tried SXDE 1/08 creating the following pool: -bash-3.2# zpool status -v tank pool: tank state:

Hi all, Sorry for the newbie question, but I''ve looked at the docs and haven''t been able to find an answer for this. I''m working with a system where the pool has already been configured and want to determine what the configuration is. I had thought that''d be with zpool status -v <poolname>, but it doesn''t seem to agree with the

Hi experts zpool import shows some weird config of an old zpool bash-3.00# zpool import pool: data1 id: 7539031628606861598 state: FAULTED status: One or more devices are missing from the system. action: The pool cannot be imported. Attach the missing devices and try again. see: http://www.sun.com/msg/ZFS-8000-3C config: data1 UNAVAIL insufficient replicas

I''ve got a Thumper running snv_57 and a large ZFS pool. I recently noticed a drive throwing some read errors, so I did the right thing and zfs replaced it with a spare. Everything went well, but the resilvering process seems to be taking an eternity: # zpool status pool: bigpool state: ONLINE status: One or more devices has experienced an unrecoverable error. An attempt was

I have a customer who has implemented the following layout: As you can see, he has mostly raidz zvols but has one raidz2 in the same zpool. What are the implications here? Is this a bad thing to do? Please elaborate. Thanks, Scott Gaspard Scott.J.Gaspard at Sun.COM > NAME STATE READ WRITE CKSUM > > chipool1 ONLINE 0 0 0 > >

So, I was running my full backup last night, backing up my main data pool zp1, and it seems to have hung. Any suggestions for additional data gathering? -bash-3.2$ zpool status zp1 pool: zp1 state: ONLINE status: The pool is formatted using an older on-disk format. The pool can still be used, but some features are unavailable. action: Upgrade the pool using ''zpool

I am curious why zpool status reports a pool to be in the DEGRADED state after a drive in a raidz2 vdev has been successfully replaced. In this particular case drive c0t6d0 was failing so I ran, zpool offline home/c0t6d0 zpool replace home c0t6d0 c8t1d0 and after the resilvering finished the pool reports a degraded state. Hopefully this is incorrect. At this point is the vdev in question now has

http://defect.opensolaris.org/bz/show_bug.cgi?id=752 Summary: zfs set keysource no longer works on existing pools Classification: Development Product: zfs-crypto Version: unspecified Platform: Other OS/Version: Solaris Status: NEW Severity: blocker Priority: P1 Component: other AssignedTo:

Hi, I''ve got an OpenSolaris 2009.06 box that will reliably panic whenever I try to import one of my pools. What''s the best practice for recovering (before I resort to nuking the pool and restoring from backup)? There are two pools on the system: rpool and tank. The rpool seems to be fine, since I can boot from a 2009.06 CD and ''zpool import -f rpool''; I can

Hello... Since there has been much discussion about zpool import failures resulting in loss of an entire pool, I thought I would illustrate a scenario I just went through to recover a faulted pool that wouldn''t import under Solaris 10 U5. While this is a simple scenario, and the data was not terribly important, I think the exercise should at least give some piece of mind to those who

Hi, Experts: A customer has X4500 and the boot drives mirrored (c5t0d0s0 and c5t4d0s0) by SVM, The ZFS uses the two other partitions on these two drives(c5t0d0s3 and c5t4d0s3). If we need to replace the disk drive c5t0d0, do we need to do anything on the ZFS (c5t0d0s3 and c5t4d0s3) first or just follow the regular boot drive replacement procedure? Below is the summary of their current ZFS

Not sure what the best list to send this to is right now, so I have selected a few, apologies in advance. A couple questions. First I have a physical host (call him bob) that was just installed with b134 a few days ago. I upgraded to b145 using the instructions on the Illumos wiki yesterday. The pool has been upgraded (27) and the zfs file systems have been upgraded (5). chris at bob:~# zpool

Not sure what the best list to send this to is right now, so I have selected a few, apologies in advance. A couple questions. First I have a physical host (call him bob) that was just installed with b134 a few days ago. I upgraded to b145 using the instructions on the Illumos wiki yesterday. The pool has been upgraded (27) and the zfs file systems have been upgraded (5). chris at bob:~# zpool

(From the README) # Jeb Campbell <jebc at c4solutions.net> NOTE: This is last resort if you need your data now. This worked for me, and I hope it works for you. If you have any reservations, please wait for Sun to release something official, and don''t blame me if your data is gone. PS -- This worked for me b/c I didn''t try and replace the log on a running system. My

Hello all, I have an oi_148a PC with a single root disk, and since recently it fails to boot - hangs after the copyright message whenever I use any of my GRUB menu options. Booting with an oi_148a LiveUSB I had around since installation, I ran some zdb traversals over the rpool and zpool import attempts. The imports fail by running the kernel out of RAM (as recently discussed in the list with

I have a box running snv_134 that had a little boo-boo. The problem first started a couple of weeks ago with some corruption on two filesystems in a 11 disk 10tb raidz2 set. I ran a couple of scrubs that revealed a handful of corrupt files on my 2 de-duplicated zfs filesystems. No biggie. I thought that my problems had something to do with de-duplication in 134, so I went about the process of

Hi, I have just recovered from a ZFS crash. During the antagonizing time this took, I was surprised to learn how undocumented the tools and options for ZFS recovery we''re. I managed to recover thanks to some great forum posts from Victor Latushkin, however without his posts I would still be crying at night... I think the worst example is the zdb man page, which all it does is to ask you

Sorry for the long post but I know trying to decide on hardware often want to see details about what people are using. I have the following AS-2022G-URF machine running OpenGaryIndiana[1] that I am starting to use. I successfully transferred a deduped zpool with 1.x TB of files and 60 or so zfs filesystems using mbuffer from an old 134 system with 6 drives - it ran at about 50MB/s or